Summary of Contents for Zenitel ECP-C1
- Page 1 ECP-C1 Single Button Emergency Call Point with Built in AFIL Hearing Loop Installation and User Guide Document Ref.: U-0769-0001 - ECP-C1_v01 Issue: 01c Complete / Approved Date: 15/01/2024 Product Part Number: 1008195005...
- Page 2 All rights reserved. Information contained in this document is believed to be accurate, however, no representation or warranty is given and Zenitel GB Limited assumes no liability with respect to the accuracy of such information. U-0769-0001 - ECP-C1_v01 – Issue: 01 – Complete / Approved...
-
Page 3: Table Of Contents
All rights reserved. Information contained in this document is believed to be accurate, however, no representation or warranty is given and Zenitel GB Limited assumes no liability with respect to the accuracy of such information. U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved... -
Page 4: Safety And Precautions
The ECP-C1 should not be used in tropical environments. The ECP-C1 must not be installed in an area that is subject to a corrosive atmosphere, or may allow water or other liquids to come into contact with the external connections. -
Page 5: Overview
The light grey back box colour matches products in the Zenitel Public Address and Voice Alarm (PAVA) range which may be mounted in similar environments, including the Zenitel Station Announcement Point (SAP) microphone range. -
Page 6: Preparation
ECP-C1 – Installation and User Guide Preparation Read and observe the safety instructions and guidelines in Section “1 Safety and Precautions” on page 4. Failure to follow these instructions and guidelines may cause personal injury and/or damage to the equipment. -
Page 7: Unpacking And Handling
“Tricle Type A”. These screws and the matching hex screwdriver bits are commercially available if additional screws are required. For reference, an exploded view of the ECP-C1 help point is as below. Exploded view of the ECP-C1, with surface mounting adaptor plate U-0769-0001 - ECP-C1_v01 –... - Page 8 ECP-C1 – Installation and User Guide It is advisable to retain the original equipment packing (containers and materials) in the event that the equipment ever needs returning for service. If the packing is not to be retained, the packing materials should be either recycled or disposed of according to local regulations.
-
Page 9: Installation
Rear view of the ECP-C1 back box, showing the rear and bottom panel cable gland points. The image also shows the four rear panel screw mounting holes, as well as showing a flush mount adaptor plate fitted to the back box. -
Page 10: Connectivity
The splitter provides the power supply for the built-in AFIL, plus the Ethernet data connection and PoE+ power to the internal intercom module. Internal view of the ECP-C1 front panel assembly, showing the internal modules and the RJ45 Ethernet cable connection point. -
Page 11: Mounting
Surface Mounting The ECP-C1’s back box provides four off 5.5mm mounting holes in its rear, for mounting onto a surface. The first stage of surface mounting the unit is to remove the front panel from the back box and to store it in a safe protected location. - Page 12 ECP-C1 – Installation and User Guide Front and side views of the ECP-C1 front assembly and back box, assembled as for surface mounting. U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 12 of 29...
- Page 13 ECP-C1 – Installation and User Guide ECP-C1 back box dimensions showing four off 5.5mm rear mounting holes. The image also shows the four off optional positions for fitment of 25mm cable glands or conduit. Unused cable entry holes to be sealed with supplied blanking plugs.
-
Page 14: Flush Mounting
Depending on the environment behind the flush mounting surface it may also be necessary to seal the four off 5.5mm surface mounting holes located in the rear of the ECP-C1’s back box,. This could be done with four suitable screws and associated sealing washers. - Page 15 ECP-C1 – Installation and User Guide Oblique front view of the ECP-C1 front assembly and back box with mounting adaptor plate fitted. U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 15 of 29...
- Page 16 ECP-C1 – Installation and User Guide ECP-C1 flush mount adaptor plate dimensions showing the six off 4.5mm countersunk mounting holes. The image also shows the four off countersunk holes for the screws which mount the adaptor plate to the back box.
-
Page 17: Configuration
ECP-C1 – Installation and User Guide Configuration See the Zenitel “Turbine” series intercom information in the Turbine IP Intercom’s technical manual (A100K11194) for configuration details. U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 17 of 29... -
Page 18: Operation
ECP-C1 – Installation and User Guide Operation Front Panel Loudspeaker LED Indication (From left to right) 1- Calling 2- In Call 3- AFIL Hearing Loop Active Call Button with Braille text ECP-C1 front panel. U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved... -
Page 19: Standard Emergency Call Mode
ECP-C1 – Installation and User Guide Standard Emergency Call Mode In its standard method of operation for emergency call use, the ECP-C1 Help point is operated to make a help call by means of its single red coloured “Alarm” call button. -
Page 20: Connections
ECP-C1 – Installation and User Guide Connections ETH1: 100 / 1000BASE-T Ethernet Port Cabling Type Standard LAN cable CAT5e (minimum) Power POE+ Termination RJ45 Suggested type CAT5e FTP or STP U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 20 of 29... -
Page 21: Technical Specification
ECP-C1 – Installation and User Guide Technical Specification Mechanical Dimensions (Assembled for Surface Mounting) ........320.5mm (h) x 160.5mm (w) x 115mm (d) Depth (d) is plus the front panel button Dimensions (Flush Mounting Adaptor Plate) ..............360.5mm (h) x 200.5mm (w) Overall product depth (d) increased by 3mm Material (Front Plate) ........................ - Page 22 ECP-C1 – Installation and User Guide Management and Operation) HTTP/HTTPS (Web configuration) DHCP and static IP + IC-EDGE. Remote automatic software upgrade. Centralized monitoring LAN Control ......................... Network Access Control (IEEE 802.1x) Protocols ..IPv4 (with DiffServ), SIP, TCP, UDP, HTTPS, TFTP, RTP, DHCP, SNMP, ONVIF, CCoIP® , NTP Other EMC ..................................
-
Page 23: Mechanical Dimensions - Back Box
ECP-C1 – Installation and User Guide Mechanical Dimensions – Back Box U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 23 of 29... -
Page 24: Storage And Preservation
ECP-C1 – Installation and User Guide Storage and Preservation This product should be packed for storage in the original packing as described in the Section “10 Packing for Return” below and stored in the following environmental conditions: Away from harsh environmental conditions, such as areas that are subject to corrosive ... -
Page 25: Appendix
ECP-C1 – Installation and User Guide Appendix 13.1 Internal Wiring Diagram U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 25 of 29... - Page 26 ECP-C1 – Installation and User Guide Notes U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 26 of 29...
- Page 27 ECP-C1 – Installation and User Guide Notes U-0769-0001 - ECP-C1_v01 – Issue: 01 Complete / Approved Page 27 of 29...
- Page 28 Should any of the above apply, Zenitel reserves the right to raise any relevant charges to the customer. Zenitel shall not be liable for any indirect, special or consequential loss or damage (including without limitation any loss of profits) arising from the use of this product or for any breach of this warranty.