Summary of Contents for Patriot 6500
- Page 1 Wire Winder 6500 Owner’s Manual Manufactured by Patriot Equipment 1302 K Road Minden, NE 68959 1-308-832-0220...
-
Page 2: Table Of Contents
Table of Contents Introduction Safety and Operation Rules Safety Decals Machine Measurements Bolt Torque Table Operation Troubleshooting Service and Maintenance Storage Parts Diagram Proposition 65 Warranty Wire Winder 6500 V2024.1... -
Page 3: Introduction
INTRODUCTION Thank you for purchasing a Patriot Equipment Wire Winder! We hope you will get many years of productive use from it. The Wire Winder has been designed to perform a certain function. All product users must read and understand this manual prior to equipment operation. -
Page 4: Safety And Operation Rules
WARNING: A specific hazard or unsafe practice which could result in severe personal injury or death if proper precautions are not taken. CAUTION: Unsafe practices which could result in personal injury if proper precautions are not taken or a reminder of good safety practices. Wire Winder 6500 V2024.1... - Page 5 5. Comply with all safety warnings and cautions in this manual as well as the operator’s manuals of any tow vehicles that may be used. 6. Do not allow any riders on the machine when in use. 7. In case of any defect or awareness of potential danger, please contact Patriot Equipment at 1-800-264-6587 immediately. Wire Winder 6500 V2024.1...
- Page 6 Winder. An untrained operator exposes themselves and bystanders to possible serious injury or death. Do not modify the equipment in any way. Unauthorized modifications may impair the functions and/or safety and could affect the life of the equipment. Wire Winder 6500 V2024.1...
- Page 7 8. I have the safety lock up pins and know and understand where and when to use them. 9. I understand that any accidents that occur with the Wire Winder are my responsibilities. 10. I understand that Patriot Equipment will not be held responsible for any accidents that involve the Wire Winder.
-
Page 8: Safety Decals
4. Slowly peal back the remaining paper and carefully smooth the remaining portion of the decal in place. 5. Small air pockets can be pierced with a pin and smoothed out using a piece of decal backing paper. Wire Winder 6500 V2024.1... - Page 9 Read Manual Before Use TS2018 P65 California Warning TS2012 Single Pinch Point TS2003 Serial Number Decal TS2013 Machine Operating Warning Minden Machine Shop Inc. TS2004 Patriot Decal 1302 K Road Minden, NE 308-832-0220 CSP152 ROTARY PINCH POINT Wire Winder 6500 V2024.1...
- Page 10 WIRE WINDER DECALS TS2003 TS2004 TS-2017 TS-2018 TS2012 CSP152 TS2013 Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
-
Page 11: Machine Measurements
WIRE WINDER EMPTY WEIGHT: APPROXIMATELY 200 LBS. WIRE SPOOL CAPACITIES: STANDARD WIRE: 2 MILES (10,560 FEET) BARB WIRE: 1.25 MILES (6,600 FEET) CAUTION! FULL SPOOLS OF WIRE WILL BE HEAVY! Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1... -
Page 12: Bolt Torque Table
(N.m) manual. When using manual. When using locking elements, increase locking elements, increase torque values by 5%. torque values by 5%. 1206 Grade or Class value for bolts and capscrews are identified by their head markings. Wire Winder 6500 V2024.1... -
Page 13: Operation
Operation Wire Winder 6500 V2024.1... - Page 14 THE WIRE WINDER WILL HAVE TO BE SECURED SO THAT AS IT IS OPERATING, IT DOESN'T PULL ITSELF OUT OF THE VEHICLE. ALSO, THE WIRE WINDER NEEDS TO BE SECURED FOR SAFE TRANSPORT. THE WIRE WINDER WEIGHS APPROXIMATELY 200 LBS., EMPTY. Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
- Page 15 RETAINING HOLE WITH THE SHAFT HOLE REPLACE THE RETAINING CLIP AND LOCK INTO PLACE TO KEEP THE WIRE SPOOL IN PLACE THE WIRE WINDER IS READY TO WIND MORE WIRE Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
- Page 16 STOP THE WIRE WINDER FROM LOADING WIRE. REDUCE THE RPM ON THE ENGINE AND TURN THE ENGINE OFF. Minden Machine Shop Inc. SECURE THE WIRE ON THE SPOOL TO KEEP IT FROM 1302 K Road Minden, NE UNSPOOLING. 308-832-0220 Wire Winder 6500 V2024.1...
- Page 17 ONLY ONE OPERATOR IS ALLOWED IN THE WORK ZONE! MORE THAN ONE OPERATOR IN THE WORK ZONE CAN LEAD TO ACCIDENTAL CONTACT WITH ROTATING PARTS WHICH COULD LEAD TO SERIOUS INJURY OR DEATH! Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
-
Page 18: Troubleshooting
Engine running? Drive belt engaged? Drive belt need replaced? Chain correctly tensioned? Pulleys and sprockets spinning on shafts? Wire spool connected correctly? Spool shaft not turning true Inspect bearings for wear, replace if needed Shaft bent? Wire Winder 6500 V2024.1... -
Page 19: Service And Maintenance
5. Add stabilizers to the fuel supply to keep the fuel from spoiling or drain the system of fuel. 6. Have the wire spool empty of any wire 7. Store the Wire Winder where it will remain dry Wire Winder 6500 V2024.1... -
Page 20: Parts Diagram
Parts Diagrams Wire Winder 6500 V2024.1... - Page 21 WIRE WINDER PARTS DETAIL A Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
- Page 22 WIRE WINDER PARTS DETAIL B Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
- Page 23 WIRE WINDER PARTS DETAIL C Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
- Page 24 WIRE WINDER PARTS DETAIL D Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
- Page 25 WIRE WINDER PARTS DETAIL E Minden Machine Shop Inc. 1302 K Road Minden, NE 308-832-0220 Wire Winder 6500 V2024.1...
- Page 26 WW-6500-A012 Pulley Tensioner Handle W5/16F Plain Washer Weldment N5/16DL Lock Nut W5/16NYL Nylon Nut WW-6500-P003 Axle for Sprocket and Pulley WW-6500-P046 Rubber Handle Grip CR1901 #50x1"x13 Tooth Sprocket WW-6500-P033 Engine Pulley Retainer Plate 5017 IDLER Sprocket Idler 17 Toother for B5/16X0.75...
- Page 27 Additional information on Proposition 65 can be obtained by visiting the State of California’s Proposition 65 website: https://oehha.ca.gov/proposition-65/about-proposition-65 Summary of Proposition 65 requirements: https://oehha.ca.gov/proposition-65/general-info/proposition-65-plain-language Clear and reasonable notice requirements: https://oehha.ca.gov/proposition-65/crnr/notice-adoption-article-6-clear-and-reasonable-warnings Chemicals and substances regulated by Proposition 65: https://oehha.ca.gov/proposition-65/proposition-65-list Proposition 65 Laws and Regulations: https://oehha.ca.gov/proposition-65/law/proposition-65-law-and-regulations Wire Winder 6500 V2024.1...
- Page 28 Minden Machine Shop, Inc. has placed this decal on our products to alert the user to the possible exposures. Wire Winder 6500 V2024.1...
-
Page 29: Warranty
It is the policy of Minden Machine Shop Inc. to improve its products whenever possible and practical to do so. We reserve the right to make changes, improvements and modifications at any time without incurring the obligation to make such changes, improvements and modifications on any equipment sold previously. Wire Winder 6500 V2024.1... - Page 30 Dealer Information: Not Applicable, check here: [ ] Dealer Name: Address: City: State: Zip Code: Phone #: Email: End User Information: Purchaser: Address: City: State: Zip Code: Phone #: Email: Equipment: Serial #: Date Of Purchase: Wire Winder 6500 V2024.1...