Do you have a question about the R2DSPOT150 and is the answer not in the manual?
Questions and answers
Summary of Contents for LeuchtKraft R2DSPOT150
Page 1
R2DSPOT150 150w led moving head spot User Manual...
Page 2
SAFETY INSTRUCTIONS This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately.
Page 3
avoid a hazard. UNPACKING Thank you for choosing our LED 150W moving head light. For your own safety, please read this manual before installing the device. This manual covers the important information on installation and applications. Please install and operate the fixture with following instructions. Meanwhile, please keep this manual well for future needs.
Page 4
FEATURES & SPECIFICATIONS Features · 150W High Output White LED · 50,000 hours lifespan and low power consumption · Beam Angle 15°, focus function · Color Wheel: 7 colors +white, rotation with variable direction and speed · 1 static Gobo Wheel: 8 gobos +white, wheel rotation and shake ·...
Page 5
Dimensions PHOTOMETRIC DATA OPERATION INSTRUCTIONS The moving head is for spot effect for on-site decoration purpose. ∙ Don’t turn on the fixture if it’s been through severe temperature difference like after ∙ transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.
Page 6
This light should be keep away from strong shaking during any transportation or ∙ movement. Don’t pull up the light by only the head, or it might cause damages to the mechanical ∙ parts. Don’t expose the fixture in overheat, moisture or environment with too much dust when ∙...
Page 7
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at least 0.5m (1.5ft) away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails.
Page 8
Regardless of the rigging option you choose for your LED moving head, always be sure to secure your fixture with a safety cable. The fixture providers a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.
Page 9
For installations where the DMX cable has to run a long distance or is in an electrically noisy enviroment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω...
Page 10
MENU Address Set Set Address Numbers] [DMX] Run Mode [AUTO] Auto 1- Auto2 [SOUND] [MANUAL] Manual Test Function and Operation Pan reverse Tilt reverse Display Screen Reverse Setup [ Advanced Setting] Channel (16/14/12/10CH Select) Sensitivity (01-100) Motor zero Reset Factory Set Ver V1 System Information DMX Address...
Page 11
Tilt 0-255 0-270° Tilt Fine 0-255 Tilt Fine X, Y speed 0-255 From fast to slow LED Dimmer 0-255 0 – 100% Strobe open LED Strobe 8-250 Strobe from slow to fast 251-255 Strobe open 0-15 White Lighting 16-31 Color 1 32-47 Color 2 48-63...
Page 12
49-55 Gobo 7 56-63 Gobo 8 64-70 Gobo 8 shake speed from slow to fast 71-77 Gobo 7 shake speed from slow to fast 78-84 Gobo 6 shake speed from slow to fast 85-91 Gobo 5 shake speed from slow to fast 92-98 Gobo 4 shake speed from slow to fast 99-105...
Page 13
Gobo Rotating 0-90 96-135 136-155 Gobo Rotating 0-180 Gobo Rotating 0-720 156-175 Gobo self-rotating CW from slow to 176-215 fast Gobo self-rotating CCW rotating from 216-255 slow to fast CH10 CH10 CH12 Focus 0-255 0 – 100% 0-63 Open CH11 CH11 CH13 Prism 64-255 Prism In 0-15...
Page 14
spots (ceiling, suspension, trussing). 3) Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances. 4) The electric power supply cables must not show any damage, material fatigue or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.
Need help?
Do you have a question about the R2DSPOT150 and is the answer not in the manual?
Questions and answers