Advertisement
Available languages
Available languages
•
Always release the bail handle to turn mower off, remove
safety key and battery pack when leaving it unattended
even for a short period of time.
The following suggestions will help you to obtain
optimum runtime from your cordless mower:
•
Slow down your cutting pace in areas where the grass is
especially long or thick.
•
Avoid mowing when the grass is wet from rain or
dew-soaked.
•
Cut your lawn frequently, especially during high
growth periods.
nOTE: It is recommended that your battery pack be recharged
after each use to prolong the battery pack life. Frequent charging
will not harm your battery pack, and will ensure that the battery
pack is fully charged and ready for its next use.
nOTE: Storing the battery pack not fully charged will
shorten its life.
MAINTENANCE
This product has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper care and regular cleaning.
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
The charger and battery pack are not serviceable.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Removing and Installing Blades
(Fig. X–DD)
DANGER: RISK OF INJURY. WHEN REASSEMBLING THE
BLADE SYSTEM, ENSURE EACH PART IS REINSTALLED
CORRECTLY, AS DESCRIBED BELOW. IMPROPER ASSEMBLY
OF THE BLADES OR OTHER PARTS OF THE BLADE SYSTEM
MAY CAUSE SERIOUS INJURY.
DANGER: To reduce the risk of serious personal
injury, turn unit off, remove safety key and battery
packs before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Replacement blades are available from your
nearest authorized service center. This mower requires
replacement blades: DT20902.
WALT-recommended
e
Cut a piece of 38 mm x 89 mm timber
to keep blades from turning when removing the blade
assembly bolt
43
.
WARNING: Use gloves and proper eye protection. Turn the
mower on its side. Be careful of sharp edges of blades.
1. Position the mower on its side, with two wheels flat on
the ground.
2. Position the 38 mm x 89 mm timber
assembly
47
and outer lip of deck as shown in Fig. X to
keep the blades from turning.
3. Unscrew and remove the blade assembly bolt
counterclockwise with a 14 mm (9/16") wrench
included) as shown in Fig. X, Y.
4. Remove the keyed spacer
the blade shaft
49
.
5. Secure the blade assembly
6. Unscrew the four blade nuts
with a 14 mm (9/16") wrench
shown in Fig. Z. First unscrew the two blade nuts
blade 1
52
and remove blade 1. Then unscrew the two
blade nuts
for blade 2
51
blade hub
.
48
nOTE: The mower blades
mounting holes
55
permitting them to only be installed
onto the blade hub
48
7. Examine all pieces for damage and replace if necessary.
8. Install sharpened or new blades onto the blade hub
shown in Fig. AA, BB.
9. Blade 2
is installed first, the bolt holes being aligned
53
with the outer blade studs
hole
55
on the blade hub
nOTE: Ensure the keyed mounting hole
key
on the blade hub
57
key
should be proud of blade 2
57
10. Blade 1
52
is installed second, the bolt holes being aligned
with the inner blade studs
on the blade hub
as shown in Fig. BB.
48
nOTE: Ensure the keyed mounting hole
the key
57
on the blade hub
in Fig. BB.
nOTE: If blade 1
52
is not flush with the key
blade hub
48
, then the blades have been mounted in the
incorrect order and must be reversed.
11. Thread the four blade nuts
and
as shown in Fig. AA, BB. Hand tighten the four
58
blade nuts
51
.
nOTE: When replacing sharpened or new blades on blade
hub
48
make sure the bottom of the blade as marked
Grass Side will be facing the ground when the mower is
returned to its normal upright position.
12. Secure the blade assembly
blade nuts
51
clockwise with a 14 mm (9/16") wrench
(not included). Torque the four blade nuts
(13-20 ft-lbs).
42
(about 61 cm long)
42
between the blade
43
44
and blade assembly
45
47
in a vise
34
as shown in Fig. Z.
counterclockwise
51
44
(not included) as
51
and pull blade 2 from the
53
52
and
53
have keyed
in the correct orientation.
56
and keyed mounting
48
as shown in Fig. AA.
55
engages the
as shown in Fig. AA. The
48
.
53
58
and keyed mounting hole
engages
55
48
and sits flush as shown
57
on the
51
onto the blade studs
47
in a vise
34
. Tighten the four
to 18-27 Nm
51
EnGLIsh
(not
from
47
for
48
as
55
56
44
59
Advertisement
