Download
Share
Print this page
  1. Manuals
  2. Brands
  3. LEGO Manuals
  4. Toy
  5. Star Wars Millennium Falcon 75105 LED Lighting...
  6. Manual

LEGO Star Wars Millennium Falcon 75105 LED Lighting Kit Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Package Contents:
Star_Wars_Millennium_Falcon_75105 LED Lighting Kit
 2 x White 30cm Dot Lights
 2 x Blue 30cm Dot Lights
 4 x Flashing 30cm White Dot Lights
 5 x White Strip Lights
 1 x 12 Port Expansion Board
 1 x AA Battery Pack (Requires 3 x AA Batteries)
 4 x Lego Light Grey 1 x 1 Plate
 3 x Lego 1 x 6 Plate (any colour)
 2 x Lego Trans Red 1 x 1 Round Plate
 2 x Lego Trans Clear 1 x 1 Round Plate
 4 x Lego Light Grey 1 x 1 Round Brick
 2 x Lego 1 x 2 Technic Brick (minimum one light grey)
 4 x Lego Trans Red Lightsaber Bar
 1 x Lego 6 x 8 Plate or 8 x 8 Plate (light or dark grey)
Connecting Cables
 3 x 5cm Connecting Cable
 1 x 15cm Connecting Cable
 1 x 30cm Connecting Cable
Note:
Place wires on the surface or under the LEGO building blocks.
The wire can be place between the building blocks or under the block, but they should be placed between
the studs correctly.
Insert the connectors to the ports.
Be careful when you are operating, there's only one correct way to insert, make sure the expansion board
is upward, find the soldered "=" sign on the left of the port. When you are inserting, the side which the

Advertisement

loading

Related Manuals for LEGO Star Wars Millennium Falcon 75105 LED Lighting Kit

Summary of Contents for LEGO Star Wars Millennium Falcon 75105 LED Lighting Kit

  • Page 1  2 x Lego 1 x 2 Technic Brick (minimum one light grey)  4 x Lego Trans Red Lightsaber Bar  1 x Lego 6 x 8 Plate or 8 x 8 Plate (light or dark grey) Connecting Cables ...
  • Page 2 wires can be seen should be faced to the “=” sign and if you feel hard to insert, please stop, and don’t force it, for that may result in bent pins inside the port or overheating of the expansion board. At this point, use the tweezers to straighten the bentpins.
  • Page 3 down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector. Finally, please pay attention to the positive and negative terminals of the battery when installing the battery case. OK, Let’s Begin!
  • Page 4 Instructions for installing this kit Start with the front of the Millennium Falcon facing you and remove the cone pieces around the cockpit. Remove the front right section by holding it and pulling it to the right, away from the centre of the Millennium Falcon.
  • Page 5 Remove the front left section by holding it and pulling it to the left, away from the centre of the Millennium Falcon. This section is attached with technic pins so give it a wiggle if it isn’t coming ofl easily.
  • Page 6 We are going to install a White Dot Light in the front of each of the sections we just removed. Below are the steps for the right hand side section. Repeat these steps for the left hand side. From the back, gently pry the dark grey wedge plate up and ofl the section. Let the round plate with the hole in it and the red 1 x 2 tile come away with it.
  • Page 7 Working down the right side, remove the light grey wedge plate. Allow the round plate with the hole in it to come away with it. Put these pieces to the side as well. Still working down the right hand side, remove the remaining light grey wedge plate. Let the 1 x 2 grille plate come away with it.
  • Page 8 There is a 1 x 2 dark grey grille brick that is now accessible. Remove it. Remove the front 1 x 2 modified plate with the transparent red piece attached to it. Remove the transparent red piece.
  • Page 9 Grab one of the White Dot Lights and rest it over the stud on the 1 x 2 modified plate. Position it so that the wire comes down from the middle similar to that in the picture above. Gently place the Lego Trans Red 1 x...
  • Page 10 Pick up the plug end of the White Dot Light and feed it through the hole in the 1 x 1 modified brick with headlight (that had the 1 x 2 brick with grille behind it). As you pull the wire through and the modified 1 x 2 plate with the White Dot Light gets closer to the 1 x 1 headlight bricks, keep the wire on the underside of the 1 x 2 modified plate with the White Dot Light on it.
  • Page 11 Feed the plug end of the White Dot Light underneath the 1 x 2 dark grey plate. There is a technic brick under there with a hole in it that the plug fits through. Remove the 2 x 3 tan plate and run the wire across the point where the 1 x 2 black brick and the 1 x 2 dark grey brick corners touch.
  • Page 12 Replace the 2 x 3 tan plate and run the wire straight out along the side of the 2 x 2 dark grey plate that sits on the black brick.
  • Page 13 Replace the dark grey wedge plate with the round plate with the hole in it and the red 1 x 2 tile. Replace the light grey wedge plate with the round piece with the hole in it.
  • Page 14 Replace the 1 x 2 dark grey grille brick with the horizontal grille lines facing towards the wire.
  • Page 15 Replace the last light grey wedge with 1 x 2 grille plate on it. Repeat the above for the left section.
  • Page 16 Find the Lego Trans Clear 1 x 1 Round Plates and have them ready. Grab a Blue Dot Light and position it on top of the stud as seen in the photo above. Keep the wires facing roughly towards the back.
  • Page 17 Grab the other Blue Dot Light and position is over the stud as seen in the picture. Keep the wires pointing out to the right and gently place the Lego Trans Clear 1 x 1 Round Plate over the Blue Dot Light.
  • Page 18 Run the wire from the Blue Dot Light on the left around the back of Rey (or whoever you have in the pilot seat!) so both wires are running out to the right of the cockpit.
  • Page 19 Pick up the left hand side front section. Make sure the wire runs out the back and then down. Reattach the front section. Reattach the right hand side section, also keeping the wire running out the back and then down.
  • Page 20 Replace the cone pieces around the cockpit.
  • Page 21 Flip the Millennium Falcon up and let it rest on it’s end so you can access the bottom of the ship. There are three wires on the left hand side of the ship. Grab the plug end of one of them and feed it through the hole in side of the long light grey technic brick.
  • Page 22 There is one wire on the right hand side of the ship. Grab the plug end and feed it through the hole in side of the long light grey technic brick. Remove the 1 x 12 light grey plate that runs horizontally across the ship, just under where your wires are fed through the holes in the technic brick.
  • Page 23 Grab the 12 Port Expansion Board and connect the plug ends of the four Dot Lights. The 12 Port Expansion Board can rest in the cavity under the ship near where it is or it can hang freely. Just remember that it is there so we don’t damage as we work on other parts of the ship. Place the Millennium Falcon back on its feet in front of you where you can easily access the gun turret on top of the ship.
  • Page 24 Remove the gun turret from the turntable piece on top of the Millennium Falcon. Remove the cone pieces with the technic pin pieces in them from the bracket piece.
  • Page 25 Grab the four Lego Light Grey 1 x 1 Round Bricks. The Lego Light Grey 1 x 1 Round Bricks are going have a Flashing White Dot Light inside each of them and then be placed on the bracket piece where the cone pieces were.
  • Page 26 Place a Flashing White Dot Light just inside the larger end of the Lego Light Grey 1 x 1 Round Brick. Bend the wires similar to that shown in the picture above to make fitting easier.
  • Page 27 Attach the remaining Lego Light Grey 1 x 1 Round Bricks with Flashing White Dot Lights inside them. Find the Lego Light Grey 1 x 2 Technic Brick and feed the plug end of the cables through the hole in the centre of the brick.
  • Page 28 Pull the wires through and then attach the Lego Light Grey 1 x 2 Technic Brick to the piece immediately behind the hinge piece that has bracket piece attached to it. Find the second (any colour) Lego 1 x 2 Technic Brick and feed the plug ends of the wires through the hole in the centre of it.
  • Page 30 Lift the large round Lego piece (hatch) under the gun turret to reveal the gunner’s compartment. Attach the second (any colour) Lego 1 x 2 Technic Brick to the 2 x 6 light grey plate on the underside of the...
  • Page 31 Lower the wires in to the gunner’s compartment and close the top hatch. Flip the Millennium Falcon on to it’s side so that you can access the bottom of the ship. Remove the large round Lego piece (hatch) that the bottom gun turret is mounted to.
  • Page 32 Pull the Flashing White Dot Light wires through the bottom of the gunner’s compartment. There is a square 6 x 8 technic piece surrounding the bottom of the gunner’s compartment. Feed the Flashing White Dot Light wires through the available centre hole in the side of this piece that faces towards the front of the ship.
  • Page 33 Stand the Millennium Falcon upright again. Grab the Lego Trans Red Lightsaber Bars and fit them to the Lego Light Grey 1 x 1 Round Bricks. You don’t need to push them all the way in. Remember, there is a Flashing White Dot Light in each one, so push them in gently.
  • Page 34 Turn the Millennium Falcon around so that the back section is facing you. Remove the blue bricks with the dark grey round plates on top of them at either end of the long transparent light blue hose.
  • Page 36 Remove the 1 x 6 light grey tile and the bricks attached to the tile (they should all come ofl together) from the three sections above where the hose was. Grab two Strip Lights and a 5cm Connecting Cable.
  • Page 37 Connect the two Strip Lights using the 5cm Connecting Cable.
  • Page 38 Peel the backing ofl the Strip Lights and in the middle of the joins of each section that had the 1 x 6 tiles (and joined bricks) prepare to stick the Strip Lights on.
  • Page 39 With the middle of the Strip Light in the centre of the join of each section, there will be enough of the sticky part on the back of the Strip Light to stick to two studs on both sections. Push them against the studs so they stick.
  • Page 40 Grab the 30cm Extension Cable and plug it in to the plug on the right hand side of the Strip Light on the right. Run the cable to the right and then down in between the next section. Replace the two blue bricks attached to either end of the transparent light blue hose. The hose will need to sit a little further down the technic pin because it now needs to go over the Strip Lights.
  • Page 41 Get all the items together from the photo above; three Lego Light Grey 1 x 6 Plates, four Lego Light Grey 1 x 1 Plates, three Strip Lights and two 5cm Connecting Cables. Put one of the Lego Light Grey 1 x 1 Plates on each end of two of the...
  • Page 42 6 Plates. Put the Lego Light Grey 1 x 6 Plates that does not have Lego Light Grey 1 x 1 Plates attached to it in the middle of the other two. Connect the three Strip Lights together with the two 5cm Connecting Cables.
  • Page 43 Open up the Millennium Falcon and give yourself clear access to where Han Solo sits (when he’s not in the cockpit!). Get the Strip Lights ready. We are going to mount the centre one first.
  • Page 44 Follow the round edge of the dark grey round corner plate around to the right. Attach the Lego Light Grey 1 x 1 Plate (that is attached to the Lego Light Grey 1 x 6 Plate) to the corner of the dark grey round corner...
  • Page 45 The Lego Light Grey 1 x 1 Plate on other end of the Lego Light Grey 1 x 6 Plate will attach to the corner of another dark grey round corner plate.
  • Page 46 Attach the Lego Light Grey 1 x 1 Plate (that is attached to the Lego Light Grey 1 x 6 Plate) to the corner of the dark grey round corner plate. The Lego Light Grey 1 x 1 Plate on other end of the Lego Light Grey 1 x 6 Plate will attach to the corner of another dark grey round corner plate.
  • Page 47 Grab the 15cm connecting cable. We are going to use it to connect the Strip Lights to the 12 Port Expansion Board. With the ship facing away from you, locate the Strip Light on the left hand side. The available port on the Strip Light will be sitting above a wrench mounted on the wall.
  • Page 48 Connect the 15cm Connecting Cable to the Strip Light. Run the 15cm Connecting Cable around the back of the wrench clipped to the wall. Run the cable down and inside the hidden compartment. Run the cable down the right hand side of the clip on the right. Reattach the compartment hatch.
  • Page 49 Close up the Millennium Falcon and stand it on its end so that you can access the bottom of the ship.
  • Page 50 On the right hand side of the ship is the bottom panel of the hidden storage compartment. Push the red technic pins with stop bushes out. Pull the hidden compartment down an ofl the plates it is attached to. The 15cm Connecting Cable should now be hanging freely down.
  • Page 51 Remove the 2 x 6 white modified plate. Run the plug end of the 15cm Connecting Cable through the side of the technic brick so that it comes out above the blue 1 x 4 plate.
  • Page 52 Pull the cable through and grab the white 2 x 6 modified plate. Reattach the white 2 x 6 modified plate making sure that the 15cm Connecting Cable runs in between the studs of the white 2 x 6 modified plate that are going to be locked in to place.
  • Page 53 Connect the 15cm Connecting Cable to the 12 Port Expansion Board. Replace the hidden compartment and push the red technic pins with stop bushes back in.
  • Page 54 Look to the bottom left of the ship. The 30cm Connecting Cable should be visible down there. There is a 6 x 6 plate above the bottom left landing gear. Remove the 6 x 6 plate. Feed the 30cm Connecting Cable through the side of the technic brick. The cable runs underneath where the 6 x 6 plate was.
  • Page 55 Continue to feed the 30cm Connecting Cable up through the left most available hole in the top side of the square 6 x 8 technic piece that surrounds the bottom of the gunner’s compartment. Plug the 30cm Connecting Cable into the 12 Port Expansion Board. Replace the 6 x 6 plate above the bottom left landing gear.
  • Page 56 Replace the hatch and bottom guns. Grab the Lego 6 x 8 Plate or 8 x 8 Plate. We are going to put it over the top of the 12 Port Expansion Board and excess wire to ensure they stay up and out of the way.
  • Page 57 Stand the ship upright again with the front facing away from you. Open up the roof sections so you can access the interior of the back of the ship. Locate the available Strip Light port that runs along the right hand side of the ship. Grab the Standard Battery Pack and put three AA batteries in it.
  • Page 58 The last thing to do is plug the Standard Battery Pack plug into the Strip Light. CONGRATULATIONS! You have finished. Turn the Standard Battery Pack on and enjoy the lights!