Summary of Contents for MRS MST 1200
- Page 1 USER MANUAL TECHNICAL AND OPERATING DOCUMENTATION WORKSHOP WASHERS TYPE: MST 1200 Manufacturer: P.W Marwis Ul. Przylep – Zakładowa 17 66-015 Zielona Góra Tel: 669-100-666 E-mail:marwis@marwis.pl...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1.0. Introduction………………………………………………………………………………………………………. 2.0. Important information ………………………………………………………………………………………. 3.0. Intended use of the device …………………………………………………………… ………………….. 4.0. Transport and storage ……………………………………………………………………………………….. 5.0. Construction and operation ……………………………………………………………………… ………. 5.1. Building………………………………………………………………………………………………………………. 5.2. Action…………………………………………………………………………………………………………………. 6.0. Technical characteristics ………………………………………………………… ………………………… 7.0. User manual………………………………………………………………………………………………………. 7.1. -
Page 3: Introduction
The purpose of this documentation is to acquaint the user with the construction, operation and maintenance of the MST 1200 WORKSHOP WASHER. This documentation should be read by all persons authorized to operate these devices, including maintenance personnel and management supervision. -
Page 4: Construction And Operation
5.0. Construction and operation 5.1. Building MST 1200 workshop washers have a rigid, welded load-bearing structure made of steel sections and sheets. The entire structure is covered with an aesthetic varnish coat. MST 1200 washers are stationary devices. The design of the washers includes the following design and functional units:... -
Page 5: Action
5.2. Action The operation of the MST 1200 washers is based on the removal of greasy impurities from the products using a flow brush through which the washing liquid flows. It is a fluid with the trade name "Clean Professional". It has special cleaning and degreasing properties, in accordance with the fluid safety data sheet. -
Page 6: User Manual
7.0. User manual The task of this manual is to familiarize the user with the correct and safe operation of the MST 1200 stationary washers throughout their lifetime. Both during the manufacturer's warranty period and in the post-warranty period. We remind you that compliance with the basic obligations of the user, required and controlled during the... -
Page 7: Preparation For Commissioning
- create a "Operation book of the device", where you should note all faults and disruptions in the washer's operation, leaving important information for other employees, affecting the safety of operation. 7.2. Warning signage - pictograms All washers have full information and warning signs (stickers, inscriptions). The purpose of this marking is to graphically highlight the most important recommendations and warnings in the most important places for the safe and proper operation of the device. -
Page 8: Commissioning And Operation
7.5. Operating notes MST 1200 washers are devices that are easy to use and do not pose any operating problems. It is sufficient to comply with the general requirements contained in this documentation and to exercise due care in the performance of the required technical inspections. -
Page 9: Current Service And Periodic Inspections
- it is strictly forbidden to arbitrarily mix the “CLEAN PROFESSIONAL” liquid with other additives, - it is forbidden to use the washer when there is no fluid in the circulation system. This can lead to irreversible damage to the pump, - the degree of contamination of the washing fluid should be checked on an ongoing basis. -
Page 10: Environmental Protection Guidelines
8.1. Current maintenance and operating activities Attention! The term “current activities” means their realization according to the identified needs resulting from the daily control and assessment of the technical condition of the device and installed accessories. Part name Quantity Comments Pump Pneumatic cylinder 1(2) -
Page 11: List Of Spare Parts
10.0 List of spare parts During the warranty period, the manufacturer of the device is obliged to replace the defective parts according to the needs identified by its service. After the warranty period expires, the parts can be manufactured according to the customer's needs, in accordance with the device documentation. - Page 12 Workshop washer stand manual - model: MST 1200 WASHING PARTS ! ATTENTION ! Only one person is required to operate the machine - during the entire work cycle, only that person can and should be in the immediate vicinity of the machine.
- Page 13 turn off the pump on the device switch, switch off the power supply at the main switch, remove the product and clean the worktop, lift the worktop and remove all remaining impurities from the bathtub, close the washer cover (additional option), ATTENTION.
- Page 14 Use protective gloves Use respiratory protection Use protective glasses Use protective clothing Use safety shoes...
Need help?
Do you have a question about the MST 1200 and is the answer not in the manual?
Questions and answers