Advertisement
PROBLEM SOLVING
If a particular Module won't go on or
off from the buttons on the Touch Tone
Controller:
Check that you have power to the outlet
controlling the Module and that the switch
on the light or appliance is on.
Check that the Unit Code on the Module is
set to the correct number. Check that the
Housecode on the Module and the Touch
Tone Controller are set to the same letter.
Try plugging the Module and the Touch
Tone Controller into the same outlet (top
and bottom). If the Module doesn't work in
ANY outlet, replace the Module. If the
Module works in some outlets but not
others, visit: www.x10.com/support for
help.
If you can't control ANY modules from
the Touch Tone Controller:
Check that you have power to the outlet for
the Touch Tone Controller. Check that the
Housecode on the Touch Tone Controller
is set correctly. Try plugging the Module
and the Touch Tone Controller into the
same outlet (top and bottom). If you can't
control ANY of your Modules, replace the
Touch Tone Controller. If the Touch Tone
Controller works in some outlets but not
others, visit: www.x10.com/support for
help.
If the Touch Tone Controller answers
the phone too soon and prevents your
answering machine from picking up:
Set the MIN MAX Delay Switch on the
Touch Tone Controller to MAX (35
seconds).
6
INTERCOM SYSTEMS
Intercom systems that send voice signals
over existing house wiring can interfere with
the operation of the Touch Tone
Controller when the intercom is in use. If
the intercom has its own separate wiring
or uses wireless Radio Frequency (RF)
transmissions it will not cause a problem.
POWER INTERRUPTIONS
When power is restored after a power
outage, Lamp Modules and Wall Switch
Modules will normally be off. Appliance
Modules stay in the state they were in before
the power interruption.
MANUAL (LOCAL) CONTROL
Lights and appliances connected to plug-in
Modules can be turned ON with their own
power switch. Simply turn the switch off
and on once or twice to activate the Module.
For lamps with three way bulbs you might
have to operate the switch a few times. Wall
Switch Modules can be turned on and off
from their own push button. The slide
switch under the push button is to remove
the power when changing a light bulb.
SAFETY PRECAUTIONS
Don't exceed the ratings of the Modules
(see back of Modules for details).
Don't use an Appliance Module for
anything that could be dangerous if turned
on remotely while unattended (a portable
heater for example).
Don't use the Wall Switch Module for
fluorescent lamps, ceiling fans, low voltage
lights, or any kind of appliance. Use for
Incandescent lamps up to 500 watts only.
Don't use to control an outlet.
EXPAND YOUR SYSTEM
Mini Timer MT10A
A Controller, Timer and Alarm Clock all
in one! Programs up to 4 modules to go on
and off at specific times, twice a day.
Controls 8 modules instantly. Dims lights
too.
Maxi Controller SC503
Lets you control up to 16 X10 Modules at
the touch of a button from anywhere in the
house. Dims lights too!
Mini Controller MC460
Lets you control up to 8 X10 Modules at
the touch of a button from anywhere in the
house. Dims lights too!
2-Way Home Control Interface CM11A
Set up from an IBM compatible PC to
control up to 256 X10 Modules.
ActiveHome software & cable included.
Thermostat Set-Back TH2807
Automatically sets-back your central
heating/air conditioning. Mounts on the
wall under your existing thermostat and
plugs into an Appliance Module.
Wireless Remote Control System RC5000
Lets you control 16 X10 modules from
inside or outside your home. Can also dim
and brighten Lamp Modules and Wall
Switch Modules. Works with the HR12A
PalmPad Remote and X10 RF Wall
Switches (SS13A and SS15A).
7
Lamp Module LM465
Can be Dimmed and Brightened from any
X10 Controller. Responds to "All lights
on". Rated for 300 W. Incandescent only.
2-Way version LM14A.
Appliance Module - AM486/AM466
Two pin polarized (AM486) or 3 pin
grounded (AM466). For controlling an air
conditioner, stereo, etc. anywhere in the
home. Rated 15A for heaters, coffee pots
etc.; 1/3 H.P. for motors; 400W for TVs;
500W for lamps. 2-Way versions available
AM14A (2 pin), AM15A (3 pin).
Wall Switch Module WS467
For controlling important indoor and outdoor
security lights. Replaces your existing wall
switch and installs like a regular dimmer.
Dimmed/brightened from any X10
Controller. Rated 500W incandescent only.
3 - Way Wall Switch Module WS4777
For controlling a light which is controlled
by two switches. Same features as WS467.
Split Receptacle Module SR227
Replaces existing wall outlet. The top outlet
functions like an Appliance Module, the
bottom one is a regular outlet. Rated 15A.
Controls ANYTHING which normally
plugs into a regular AC outlet.
Universal Module UM506
Isolated contact relay and beeper. Can be
set for momentary or continuous operation.
Not compatible with DS7000 and DC8700
security systems.
Advertisement
