Searching For Codes - X10 SoundPower VK59A Owner's Manual

S S S S S F F F F F C C C C C
EARCHING EARCHING EARCHING OR OR OR ODES ODES ODES
EARCHING EARCHING OR OR ODES ODES
1. 1. 1. 1. 1. Turn on the device you want to control.
2. 2. 2. 2. 2. Press and hold SETUP until the LED indicator
lights steadily. Release the Setup button.
3. 3. 3. 3. 3. Press the mode button that matches the equip-
ment you want to control (TV, VCR, Cable, AUX).
The LED blinks once.
4. 4. 4. 4. 4. Press CHANNEL + repeatedly (note 5, page 15)
until the device to be controlled changes
channel.
If you accidentally go past the code, press
CHANNEL - repeatedly until the channel
changes again.
5. 5. 5. 5. 5. Press and release the ENTER button to complete
the setup.
The above assumes that you want to store VCR codes under the VCR
button, Cable codes under CBL, etc. If you want to store a VCR code
under CBL, etc., first follow the procedure on page 15 and try ANY
CBL code from the code tables, e.g. press CBL in step 3, page 15, and
then enter ANY VCR code. Then follow the steps above.
I I I I I C C C C C
DENTIFYING DENTIFYING DENTIFYING DENTIFYING DENTIFYING ODES ODES ODES ODES FOUND ODES FOUND FOUND FOUND FOUND USING USING USING USING USING THE THE THE THE THE
1. 1. 1. 1. 1. Press and hold SETUP until the LED indicator lights steadily. Release the Setup button.
2. 2. 2. 2. 2. Press the mode button that matches the equipment you want to identify (TV, VCR,
CBL). The LED blinks once.
3. 3. 3. 3. 3. Press and release SETUP. The LED blinks once.
4. 4. 4. 4. 4. To find the first digit, press each number button from 0 to 9 until the LED blinks. The
number you pressed is the first digit of the code.
5. 5. 5. 5. 5. Press each number button from 0 to 9 again as above to find the second digit.
6. 6. 6. 6. 6. Press each number button in turn to find the third digit. When the third digit has been
found, the LED goes out.
1 6 1 6
1 6 1 6 1 6
S S S S S P P P P P
EARCH EARCH EARCH EARCH EARCH ROCEDURE ROCEDURE ROCEDURE ROCEDURE ROCEDURE
C C C C C PC F PC F PC F PC F PC F
ONTROLLING ONTROLLING ONTROLLING
ONTROLLING ONTROLLING
The UR78A remote can also control an MP3, DVD, and CD player in
your PC when used with an additional RF receiver and software. You
will need to purchase an MR26A receiver which connects to your
PC's serial port. You then download the software (called Boom) from
X10's Web Site (www.x10.com). You will then be able to control a
DVD or CD player in your PC as well as being able to control MP3
players such as MusicMatch, RealJukeBox, WinAmp, etc., remotely
from anywhere inside or outside your home.
The AUDIO button is also a PC button so to access your PC you just
press AUDIO (PC) followed by button 1 (MP3) or button 2 (DVD) or
button 3 (CD). You can then use buttons such as Play, Stop, Pause, FF,
REW, etc. to control the DVD, CD, or MP3 player in your PC.
When used in conjunction with the VT35A Audio Transmitter, and
VR32A Audio Receiver/Speaker Driver, you will be able to listen to
MP3 files stored in your PC while sitting outside having a barbecue.
1 7 1 7
1 7 1 7 1 7
UNCTIONS UNCTIONS UNCTIONS
UNCTIONS UNCTIONS
Pressing AUDIO (PC) followed by 1
(MP3) or 2 (DVD) or 3 (CD)
accesses your PC, when used with
the optional MR26A receiver and
Boom software.