Care should be taken in mounting or dismounting the ergometer. Be aware of feet when replacing the ergometer. M960906 / VERSION: 1.0 - 2019-03-26 3/22...
Page 4
Inspect the device for worn or loose components prior to use. Tighten / replace any loose or worn components prior to use. Do not place any loose parts or objects on the device before and during use. M960906 / VERSION: 1.0 - 2019-03-26 4/22...
Page 5
If the test person feels faint stop exercising immediately. The installation should only be done by authorized persons who follow the installation instructions. Do not spill any liquid over the device. M960906 / VERSION: 1.0 - 2019-03-26 5/22...
Page 6
Otherwise, degradation of the performance of this equipment could result. The operator should have knowledge about absolute and relative contraindications. The operator should have knowledge about the Warnings and Cautions before using the device. M960906 / VERSION: 1.0 - 2019-03-26 6/22...
During the intended use the test subject will deliver energy. Application of the wrong dosis of energy could lead to permanent damage of the test subject health. Only use this device under supervision of a medical physician. M960906 / VERSION: 1.0 - 2019-03-26 7/22...
Note that a A USB A-B cable is standard supplied. For rehab products this cable can only be used for service purposes. For cpet products, it can be used for connection to ECG and pulmonary testing devices as well. M960906 / VERSION: 1.0 - 2019-03-26 8/22...
Tilt the device carefully to the side and leave it resting on the handlebar. You can now connect the cables and guide them through the cable guide. Place the device upright carefully again. M960906 / VERSION: 1.0 - 2019-03-26 9/22...
To connect cables to the ergometer: tilt the device carefully to the side and leave it resting on the handlebar. Place both hands on the handle bar and step aside to prevent trapping of fingers and toes when putting it back upright. M960906 / VERSION: 1.0 - 2019-03-26 10/22...
Lift the lever under the saddle. The saddle can now be moved up and down. Release the lever to lock the saddle in position. Note: the patient should not sit on the saddle while adjusting it. M960906 / VERSION: 1.0 - 2019-03-26 11/22...
Note: the patient should not lean on the handlebar while adjusting it. 7 - List of symbols used Read manufacturer’s guide, advises and instructions and manual Potential Equalization Conductor CE and notified body M960906 / VERSION: 1.0 - 2019-03-26 12/22...
Page 13
The equipment has a safety earth (ground) connection and must be connected to an earthed (grounded) wall socket. External Input External Control Connector Class I MEDICAL EQUIPMENT Type B Electrical Safety IEC 60601-1 General warning M960906 / VERSION: 1.0 - 2019-03-26 13/22...
Opening of the equipment by unauthorized agencies is not allowed and will terminate any claim to warranty. Lode will make available on request circuit diagrams, component part lists, descriptions, calibration instructions, or other information that will assist authorized service personnel to repair those parts of the ergometer that are designated by Lode as repairable by authorized service personnel.
The ergometer should be calibrated once a year. In case any damage is observed of the ergometer Lode B.V. or his representative should be informed in order to execute the necessary repair(s). Service of the ergometer is restricted to factory-trained personnel only.
12.1 - Emissions test The Lode equipment is intended for use in the electromagnetic environment specified below. It is the responsibility of the customer or user to ensure that the Lode equipment is used in such an environment. Emissions test: RF emissions CISPR11...
12.2 - Immunity test The Lode equipment is intended for use in the electromagnetic environment specified below. It is the responsibility of the customer or user to ensure that the Lode equipment is used in such an environment. Immunity Test: Electrostatic discharge (ESD) EN 61000-4-2 Immunity Test: IEC 60601-Test Level: ±...
Page 18
Interference The Lode equipment is intended for use in the electromagnetic environment specified below. It is the responsibility of the customer or user to ensure that the Lode equipment is used in such an environment. Immunity test: Conducted RF 61000-4-6...
Recommended Separation Distances between Portable and Mobile RF Communication Equipment and the Lode equipment The Lode equipment is intended for use in the electromagnetic environment on which radiated RF disturbances are controlled. The customer or the user of the Lode equipment can help prevent...
Accessories Electric adjustable Suunto Belt HR Smart saddle height Bluetooth Partnumber: 960810 Partnumber: 960810 Partnumber: 928639 Partnumber: 928639 Easy and accurate Smart connection positioning Electric adjustable saddle Suunto Belt HR Smart height Bluetooth M960906 / VERSION: 1.0 - 2019-03-26 20/22...
7 inch Touchscreen Connectivity Lode interface protocol Dimensions Product length (cm) 105 cm 41.3 inch Product width (cm) 46 cm 18.1 inch Product height 114 cm 44.9 inch Product weight 65 kg 143.3 lbs M960906 / VERSION: 1.0 - 2019-03-26 21/22...
Page 22
Maximum storage & transport air pressure 106 kPa Minimum air pressure storage & transport 50 kPa Max. humidity storage & transport 95 % Order info Min. humidity storage & transport 10 % Partnumber 960906 M960906 / VERSION: 1.0 - 2019-03-26 22/22...