Summary of Contents for Eizo TIP2010-DVI
- Page 1 Instructions for Use IP Transceiver Important Please read the safety information and all information delivered with the product carefully to familiarize yourself with safe and effective usage.
-
Page 2: Legal Information
Use of EIZO products WARNING EIZO products may only be used for the applications described in the catalog and in the relevant tech- nical documentation. If products and components from other manufacturers are used, these must be recommended or approved by EIZO. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. -
Page 3: Table Of Contents
Table of contents Table of contents Legal information ...................... 2 1 Introduction........................ 5 Contents of this document .................. 5 User groups ...................... 5 2 Safety information ...................... 6 General safety instructions .................. 6 Product-specific safety instructions ................ 9 3 Description........................ 10 Scope of delivery .................... 10 Intended use ...................... 11 Features........................ 11 Applications ...................... 13... - Page 4 Table of contents 10.3 Interfaces ........................ 30 10.4 Power supply ...................... 30 10.5 Mechanical design .................... 31 10.6 Climatic conditions.................... 31 10.7 Safety regulations .................... 31 11 Dimension drawings ...................... 32 11.1 View from in front, below, and rear ................. 32 12 Appendix ......................... 35 12.1 Information on electromagnetic compatibility (EMC) .......... 35 12.2 Markings and symbols .................... 38 12.3 Warranty ......................... 39 12.4 Repairs ........................ 39...
-
Page 5: Introduction
This documentation is available in electronic format only. It can be downloaded at www.eizo-or.com, or provided by the sales partner from whom you purchased the product. This document explains the functionality and the intended use of the IP Transceiver. To en- sure clarity, it does not contain all detailed information on this product. -
Page 6: Safety Information
2 Safety information 2.1 General safety instructions Correct and safe operation of EIZO devices assume professional transport, storage, installa- tion, and connection, as well as careful operation and service. The devices may only be used for applications for which they are intended. - Page 7 Safety information 2.1 General safety instructions DANGER Please observe all warning information present on the device and in the instructions for use There is a danger to life if warnings are not obeyed. Severe personal injury or damage to property may occur.
- Page 8 Safety information 2.1 General safety instructions CAUTION Extensive damage to property may result if the device is not connected correctly That is why you should observe the warning information: • Desktop installation: Place the device on a solid and level surface. The attached stand, as well as the installation sur- face, must be suitable for the weight of the device.
-
Page 9: Product-Specific Safety Instructions
Safety information 2.2 Product-specific safety instructions 2.2 Product-specific safety instructions NOTICE Network security • Make sure the network environment is secure. • Follow the information in 60601-1, Chap. 16, ME Systems. TIP0210-DVI Instructions for Use, 12/2022... -
Page 10: Description
Description 3.1 Scope of delivery 3 Description 3.1 Scope of delivery The scope of delivery includes the device, and in some versions various components. After unpacking, check the scope of delivery for correctness and completeness. Note Keep the packaging material for subsequent transport of the device. Device The IP Transceiver is offered in the following versions. -
Page 11: Intended Use
The IP Transceiver is the central element of the CuratOR Alipe system. CuratOR Alipe is an IP-based solution for flexible data transmission in the operating room (OR). With this EIZO system, image and video data can be transmitted without compression, both within and out- side the OR. - Page 12 Description 3.3 Features Two video signals simultaneously With the TIP0210-DVI and TIP0410, up to two video links can be processed in parallel. As such, the video interfaces can be used as input and output at the same time. In addition, a connected FHD signal can be looped through.
-
Page 13: Applications
Description 3.4 Applications 3.4 Applications WARNING Service personnel • The IP Transceiver may only be used by service personnel that perform technical instal- lations either in medical environments or of signal processing systems. • When the IP Transceiver is used with the Large Monitor Manager (LMM), service per- sonnel must also have knowledge of LMM operation. -
Page 14: Setup And Installation
Setup and installation 4.1 Setup and installation location 4 Setup and installation CAUTION Changes to device Do not make any mechanical or electric changes to the device. Otherwise the device war- ranty becomes invalid. The manufacturer is not liable for changes made to the device. 4.1 Setup and installation location CAUTION Overheating of the device... -
Page 15: Positioning As A Desktop Device
Setup and installation 4.2 Positioning as a desktop device NOTICE Condensation If the device is brought into a warm environment from a cold one, condensation may form in the device. This could result in a short circuit when switching on the device, damaging it. •... - Page 16 Setup and installation 4.3 Installation Screw specifications for the rack Thread Strength Screw length 8 mm Maximum tightening torque 3 Nm Procedure 1. Attach the two holders on the back of the IP Transceiver using the four M3 screws pro- vided. CAUTION: Comply with the maximum tightening torque of the screws.
-
Page 17: Connecting
Connecting 5.1 Safety information for connection 5 Connecting 5.1 Safety information for connection Observe all safety information and warnings for the device to ensure danger-free operation. CAUTION Shielding measures Follow all shielding measures in accordance with local EMC directives. If these guidelines are not observed, device malfunction may result. -
Page 18: Device Connectors
Connecting 5.2 Device connectors 5.2 Device connectors Front connectors TIP0210-DVI Audio RS232 USB B USB A DVI-D 0 DVI-D 1 Connector Type Function USB A USB Downstream For connecting external USB HID devices. USB B USB Upstream For connecting to the USB HID host. Audio Jack For connecting analog audio devices. - Page 19 Connecting 5.2 Device connectors Front connectors TIP0810 USB A USB B Audio RS232 HDMI (out) HDMI (in) Connector Type Function USB A USB Downstream For connecting external USB HID devices. USB B USB Upstream For connecting to the USB HID host. Audio Jack For connecting analog audio devices.
-
Page 20: Connection Procedure
Connecting 5.3 Connection procedure Rear connectors TIP0410 and TIP0810 SFP+ Status LED RJ45 Power connector Grounding Connector Type Function SFP+ SFP+ chassis For inserting the SFP+ module (available separately) for optical network connections. CAUTION: To prevent malfunctions, only the SFP+ modules listed in chapter Inputs/Outputs [} 27] may be used. - Page 21 Connecting 5.3 Connection procedure CAUTION Neutral conductor The power supply unit provided is designed for line power with a grounded neutral conduc- tor. • To avoid risk of electric shock, this device must only be connected to line power with a protective conductor.
-
Page 22: Commissioning
Commissioning 5.3 Connection procedure 6 Commissioning Note Service personnel put theIP Transceiver into operation when installing the CuratOR Alipe. TIP0210-DVI Instructions for Use, 12/2022... -
Page 23: Operation
Operation 7.1 Switching on / off 7 Operation After start-up of the IP Transceiver, user operation consists of switching the power on and off. After switching on the IP Transceiver, the Status LED flashes green. In normal mode, the Status LED flashes once per time interval of about 3 seconds. 7.1 Switching on / off The IP Transceiver is connected to line power with a power supply unit. -
Page 24: Cleaning And Check Settings
Cleaning and check settings 8.1 Cleaning 8 Cleaning and check settings 8.1 Cleaning CAUTION Device maintenance, cleaning and disinfecting • The device is sensitive to mechanical influences. Avoid mechanical shocks or similar. • Make sure liquids do not seep into the device. Liquids that seep into the device may re- sult in an electric shock or failure of the device. -
Page 25: Maintenance
Cleaning and check settings 8.2 Maintenance Prohibited cleaning agents and disinfectants The following cleaning agents and disinfectants could lighten the finish and are therefore prohibited. Agent class Tested cleaning agents Further examples and disinfectants Alcohol Ethyl alcohol, 96 % Hospiset cloth Disinfectants Mikrozid liquid Petroleum spirit... -
Page 26: Troubleshooting
Troubleshooting 9.1 Status LED 9 Troubleshooting 9.1 Status LED In IP Transceiver normal mode, the Status LED flashes once per time interval of about three seconds. After each flash there is a brief pause so that the number of flashes can be counted. -
Page 27: Technical Specifications
Technical specifications 10.1 Inputs/Outputs 10 Technical specifications 10.1 Inputs/Outputs Type Network connection SFP+ (10 Gbit/s - Ethernet) CAUTION: To avoid malfunctions, only the fol- lowing SFP+ modules may be used: • Avago AFBR-708SMZ • Avago AFBR-709SMZ • FCI TRX10GVP2010C1 • FCI TRX10GVP2010C2 •... -
Page 28: Supported Video Timing Values
Technical specifications 10.2 Supported video timing values 10.2 Supported video timing values Input Output CEA-861 CEA-861 format VESA format format SXGA UXGA WUXG (p60) (p50) (p30) (p60) TIP0210 TIP0210 TIP0210 TIP0210 TIP0210 TIP0210 TIP0210 TIP0410 TIP0410 TIP0410 TIP0410 ... - Page 29 Technical specifications 10.2 Supported video timing values Input Output VESA format CEA-861 format VESA format SXGA UXGA WUXG (p60) (p50) (p30) (p60) TIP0210 TIP0210 TIP0210 TIP0210 TIP0210 TIP0210 TIP0210 TIP0410 TIP0410 TIP0410 TIP0410 TIP0410 TIP0410 TIP0410 TIP0410 TIP0810 TIP0810 TIP0810...
-
Page 30: Interfaces
Technical specifications 10.3 Interfaces 10.3 Interfaces TIP0210-DVI Type DVI-D (in / out) DVI-D (out / loop through) TIP0410 Type HDMI (in) HDMI (out / loop through) TIP0810 Type HDMI (in) HDMI (out) 10.4 Power supply Power supply External power supply, 230 V AC Rated voltage 12 VDC Consumption... -
Page 31: Mechanical Design
Technical specifications 10.5 Mechanical design 10.5 Mechanical design Housing Aluminum (color: silver) Degree of protection IP20 Dimensions (W x H x D) in mm 164 x 166 x 38.5 mm (height of cooling fins: 6 mm) Weight 1.05 kg 10.6 Climatic conditions In operation Temperature range 0 °C - 40 °C ambient temperature... -
Page 32: Dimension Drawings
Dimension drawings 11.1 View from in front, below, and rear 11 Dimension drawings All dimensions in mm 11.1 View from in front, below, and rear TIP0210-DVI TIP0210-DVI Instructions for Use, 12/2022... - Page 33 Dimension drawings 11.1 View from in front, below, and rear TIP0410 TIP0210-DVI Instructions for Use, 12/2022...
- Page 34 Dimension drawings 11.1 View from in front, below, and rear TIP0810 TIP0210-DVI Instructions for Use, 12/2022...
-
Page 35: Appendix
Appendix 12.1 Information on electromagnetic compatibility (EMC) 12 Appendix 12.1 Information on electromagnetic compatibility (EMC) IP Transceiver were designed to distribute and switch video, audio, and control signals in real time. NOTICE Special EMC provisions are required for use of the IP Transceiver. Installation, assembly, and use must take place in compliance with the following instructions: •... - Page 36 Appendix 12.1 Information on electromagnetic compatibility (EMC) Information and manufacturer’s declaration – electromagnetic radiation The IP Transceiver is intended for use in the electromagnetic environments noted below. The customer or user of the IP Transceiver has to ensure that the device is used in such an environ- ment.
- Page 37 Appendix 12.1 Information on electromagnetic compatibility (EMC) Information and manufacturer’s declaration – electromagnetic radiation The IP Transceiver is intended for use in the electromagnetic environments noted below. The customer or user of the IP Transceiver has to ensure that the device is used in such an environ- ment.
-
Page 38: Markings And Symbols
Appendix 12.2 Markings and symbols Recommended minimum distance between portable and mobile RF communications devices and the IP Transceiver The IP Transceiver is intended for use in an electromagnetic environment in which interference due to electromagnetic radiation is controlled. The customer or user of the LMM can help prevent electromagnetic interference by maintaining the recommended minimum distance between portable and mobile RF communications devices (trans- mitter) and the monitor as shown below. -
Page 39: Warranty
The device is in compliance with directive 2011/65/EU for limiting the use of specific haz- ardous materials in electric and electronic devices. 12.6 Additional devices Connected devices such as network routers must meet the relevant safety standards. 12.7 Contact Support during installation and for technical questions www.eizo-or.com TIP0210-DVI Instructions for Use, 12/2022... -
Page 40: Trademarks
ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United States and other countries. EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, Radi- Force, RadiNET, Raptor and ScreenManager are registered trademarks of EIZO Corpora- tion in Japan and other countries. -
Page 41: Index
Index Index Ambient temperature 31 Cleaning 24 Cleaning staff 5 Connector 18, 19 Contact 39 Disposal 39 General safety instructions 6 Input 18, 19 Output 18, 19 Overheating 14 Power connector 21 Rack 15 Scope of delivery 10 Service personnel 5 Shielding measures 17... - Page 42 Carl-Benz-Straße 3 76761 Rülzheim Germany Instructions for Use, 12/2022 TIP0210-DVI Copyright © 2022 . All rights reserved. 1083173-004...