Advertisement
Quick Links
TRANSI T VAN RE AR TIRE CARR IE R AN D L ADD ER
TR110 6B
INSTALLATION
GUIDE
F L AT L I N E VA N C O • S U P P O R T @ F L AT L I N EVA N C O . C O M • 8 8 8 - 6 6 7- 5 5 7 6
TOOLS REQUIRED
(NOT INCLUDED)
+
5/32" ALLEN WRENCH
+
6MM ALLEN WRENCH
+
POWER DRILL
+
13MM SOCKET
+
3/16" DRILL BIT
+
13/16" SOCKET
+
27/64" DRILL BIT
+
9/16" WRENCH
+
3/4" WRENCH
+
7/16" WRENCH
+
AUTO PANEL REMOVAL TOOL
+
7/32" ALLEN WRENCH
INSTALL INFO
TIME TO INSTALL THIS PRODUCT: 1-2 HOURS
Additional help is suggested for a few of the install
steps.
BEFORE YOU START
Please inspect the product and packaging upon
delivery to ensure there are no issues and that all
parts and hardware are accounted for.
Contact us ASAP if anything is missing at:
support@flatlinevanco.com
0 1
Advertisement
Summary of Contents for FVC TR1106B
- Page 1 INSTALLATION GUIDE TRANSI T VAN RE AR TIRE CARR IE R AN D L ADD ER TR110 6B TOOLS REQUIRED (NOT INCLUDED) 5/32” ALLEN WRENCH 6MM ALLEN WRENCH POWER DRILL 13MM SOCKET 3/16” DRILL BIT 13/16” SOCKET 27/64” DRILL BIT 9/16”...
-
Page 2: Before You Start
BEFORE YOU START All Flatline Van Co products must be properly assembled and secured before attaching to your vehicle. Improper attachment could result in an automobile accident, and could cause serious bodily injury or death to you or to others involved. You are responsible for assembling and securing Flatline Van Co products to your vehicle, checking the mounting points and attachments prior to use, and regularly inspecting the products for wear and or damage. -
Page 3: Package Contents
PACKAGE CONTENTS WHEEL BRACKET BACKER PLATES FRONT DRILL TEMPLATE SIDE DRILL TEMPLATE QTY: 1 QTY: 2 QTY: 1 QTY: 1 TIRE CARRIER QTY: 1 LOWER HINGE BRACKET UPPER HINGE BRACKET INTERNAL BRACE LOCK ROD QTY: 1 QTY: 1 QTY: 1 QTY: 1 FRAME BRACE QTY: 1... - Page 4 HARDWARE 3/8-16 X 1 FLANGED HEX 3/8-16 X 3 BUTTON HEAD 1/2-13 X 1.5 SQUARE NECK 1/4-20 X 1.0 FLANGED HEAD SCREW HEX DRIVE SCREW M14-1.5 LUG NUT CARRIAGE BOLT BUTTON HEAD HEX DRIVE QTY: 1 QTY: 8 QTY: 3 QTY: 4 QTY: 1 M14-1.5 X 65 WHEEL STUD...
- Page 5 INSTALL TOOLS REQUIRED FOR THIS STEP: AUTO PANEL REMOVAL TOOL STEP | 01 LAYOUT AND INSTALL PREP 1.1 Door Panel Removal: Remove the Lower Panel Trim (FIG 1) using plastic panel removal tools. Be gentle to avoid breaking the factory panel clips. If clips get stuck in the door, pop them out and slide them back into place on the trim panel.
- Page 6 TOOLS REQUIRED FOR THIS STEP: MARKER MEASURING TAPE POWER DRILL 3/16” DRILL BIT 27/64” DRILL BIT STEP | 02 DRILL FOR THIRD MOUNT 2.1 Marking Front Drill Location: Use the Front Drill Template to mark the outside of the rear driver door. The arrows should align with the edge of the sheet metal under the window and the right side of the door as shown in FIG 3.
-
Page 7: Step | 03 Bracket Assembly
3/4” WRENCH OR SOCKET TOOLS REQUIRED FOR THIS STEP: 9/16” WRENCH OR SOCKET STEP | 03 BRACKET ASSEMBLY 3.1 Assemble the Tire Carrier: Attach the Wheel Bracket to the Tire Carrier Frame using: (2) Backer Plates, (4) 1/2-13 X 1.5 Square Neck Carriage Bolts, (4) 1/2 Screw Flat Washers, And (4) 1/2-13 Nylon Insert Locknuts and a 3/4”... - Page 8 TOOLS REQUIRED FOR THIS STEP: MARKER RATCHET 13MM SOCKET STEP | 04 HINGE BRACKET INSTALL 4.1 Bottom Hinge Alignment Marks: Begin by marking align- ment points at the bottom hinge of the driver-side door (FIG 9). 4.2 Release Bottom Hinge: Remove the three factory bolts of the lower hinge using a 13MM Socket (FIG 10).
- Page 9 TOOLS REQUIRED FOR THIS STEP: STEP | 05 SECURE CARRIER 5.1 Hinge Mounts: With assistance, raise the carrier up to the door and insert (2ea) 3/8” Flanged Hex Head Screws through the Upper (FIG 13) and Lower (FIG 14) Hinge Brackets. Loosely thread on (2ea) 3/8”...
- Page 10 RATCHET TOOLS REQUIRED FOR THIS STEP: 9/16” WRENCH 7/16” WRENCH 5/32” ALLEN WRENCH 7/32” ALLEN WRENCH STEP | 05 SECURE CARRIER 5.3 Internal Brace: Install the Internal Door Brace over the inserted 3/8” Bushing Assembly Bolt, keeping it in place by loosely threading on a 3/8”...
- Page 11 TOOLS REQUIRED FOR THIS STEP: 6MM ALLEN WRENCH 13/16” SOCKET STEP | 06 ATTACH WHEEL LOCTITE HERE 6.1 Wheel Studs and Lug Nuts: Apply Loctite to the Wheel Studs on the short end and screw them into the notched locations on the Wheel Bracket. Tighten with a 6MM Allen Wrench (FIG 20).
-
Page 12: Step | 07 Foot Pegs
TOOLS REQUIRED FOR THIS STEP: FOOT PEG WRENCH STEP | 07 FOOT PEGS 7.1 Foot Pegs: Thread on Foot Pegs to locations shown in FIG 22 and use the provided Foot Peg Wrench to tighten foot pegs to carrier (FIG 23). FOOT PEGS F I G 2 2 F I G 23... - Page 13 FVC (and see) from you! Head to the products and following along and we will make it right. FVC is product page and click “Leave a company of van and outdoor with your adventures. Tag us Review.”...
Need help?
Do you have a question about the TR1106B and is the answer not in the manual?
Questions and answers