Related Manuals for TITTLA KMBC100
Summary of Contents for TITTLA KMBC100
- Page 1 INSTRUCTION MANUAL BUILT-IN BEVERAGE COOLER MODEL: KMBC100 E-mail：support@tittla.com Phone：1(510)228-4672 Read this manual and follow all safety rules and operating instructions before the first use of this beverage cooler.
-
Page 2: Table Of Contents
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS PRODUCT DIAGRAM INSTALLATION INSTRUCTIONS Before Using Your Beverage cooler To Install Stainless Steel Handle To Install Your Beverage cooler OPERATION INSTRUCTIONS Controls Storage Door Lock Shelves CARE & MAINTENANCE Cleaning Your Beverage cooler Power Failure Vacation Time Moving Your Beverage cooler Energy Saving Tips... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Your safety and the safety of others are very important. This Beverage cooler complies with the applicable safety requirements and is safe for daily use. However, basic safety precautions should always be followed when using an electrical appliance, to reduce the risk of fire, electric shock, and personal injury. - Page 4 Do not use this beverage cooler for other than its intended purpose. For indoor, household use only. Move this beverage cooler by 2 people. Failure to do so can result in injury. Place this beverage cooler in a well-ventilated area with temperatures above 15°C (60°F) and below 32°C (90°F).
-
Page 5: Product Diagram
CAUTION - To prevent a child from being entrapped, keep out of reach of children and not in the vicinity of the cooler. PRODUCT DIAGRAM Control Panel Shelves Exhaust Window Leveling Legs Top Hinge Glass Door with Handle Basket INSTALLATION INSTRUCTIONS Before Using Your Beverage cooler ... -
Page 6: To Install Stainless Steel Handle
Install the handle on the left side of the door. To Install Stainless Steel Handle 1) Pull away the door gasket in the area where the handle is to be installed, as Illustration #1. The gasket is easily removed by hand, no tools are necessary. 2) Align the handle with the preinstalled screws on the door frame. - Page 7 to perform properly. It is not advisable to install this cooler in moist areas or directly adjacent to a kitchen sink, as moisture could cause premature corrosion to the components of your new cooler. It is recommended you install the Beverage cooler in a place with temperatures above 60°F (15°C) and below 90°F (32°C), and humidity is under 60%.
-
Page 8: Operation Instructions
OPERATION INSTRUCTIONS Controls After plugging the Beverage cooler into a wall outlet, the cooler would turn on automatically and the LCD screen would show the temperature inside of the cooler. After setting your desired serving temperature, allow the cooler to cool down for 3 to 4 hours before placing cans beverage cooler. -
Page 9: Shelves
Remove the key and put it in a secure location. Shelves To remove the shelves from the track, pull each shelf out to the shelf post,as shown in figure A. Lift it up again, then slowly pull the shelf out, as shown in figure B. CARE &... -
Page 10: Power Failure
Power failure Most power failures are corrected within a few hours and should not affect the temperature of your Beverage cooler. If the power is off for an extended period of time, proper steps should be taken to protect your contents. Vacation Time Leave the Beverage cooler operating during vacations of less than three weeks. -
Page 11: Troubleshooting Guide
TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION The Beverage cooler may not be Ensure the Beverage cooler has been plugged in, or plug may be loose. plugged in properly. The Beverage Press to turn on the cooler. cooler does not The Beverage cooler is turned off. run. - Page 12 PROBLEM POSSIBLE CAUSE SOLUTION Not plugged in. Plug the cooler in. The circuit breaker tripped The light does not Check the breaker and fuses. or a blown fuse. work. Press to turn the light ON. The light button is “OFF”. The cooler is not level.
- Page 13 15 days of receipt of the product. 2. Customers are entitled to free repair service from TITTLA for any product proven defective in material or workmanship that results in product failure during normal consumer usage and conditions within the valid warranty period, which is 12 months from the date of selling.
Need help?
Do you have a question about the KMBC100 and is the answer not in the manual?
Questions and answers