Subscribe to Our Youtube Channel
Summary of Contents for Scott CR30X30SS
- Page 1 SCOTT EQUIPMENT COMPANY Dominator Crusher Instruction Manual NEPTUNE TECHNOLOGIES 4141 Comtois Sherbrooke, Quebec Canada J1L 1R7 Job No.: 13-071 Engineer: A.MANAEN Model No.: CR30X30SS Serial No.: 1304071 Page 1 of 17...
- Page 2 Dominator Crusher Operational Manual Manufactured by - SCOTT EQUIPMENT COMPANY 605 4th Ave. N. W. New Prague, MN. 56071 Phone: #952-758-2591 Toll Free: #1-800-264-9519 Fax: #952-758-4377 Web address: http://www.scottequipment.com/scotte MARKETS SERVED ♦ Agriculture ♦ Industrial ♦ Plastic ♦ Chemical ♦ Lumber ♦...
-
Page 3: Table Of Contents
Table Of Contents Introduction ........................Pre-start up Check List ....................Safety ..........................Installation ........................General considerations Mounting considerations Electrical considerations Tips for Operation ......................Troubleshooting General Maintenance ...................... Warranty and Terms ......................Conditions of Sale ......................Guarantee ........................Parts List .......................... Page 3 of 17... -
Page 4: Introduction
Introduction On behalf of Scott Equipment Company, thank you for your recent investment in the Scott product line. Superior quality and service are the backbone of Scott Equipment and we are committed to providing you with durable equipment that is built for today to last for tomorrow. -
Page 5: Pre-Start Up Check List
Pre-start Up Check List 1) If your equipment is supplied with gear speed reducer make sure it is filled with the proper weight and amount of oil. (Gear boxes are shipped without oil from the factory.)The recommended level and types of lubricants are listed in the factory manual included in this manual. -
Page 6: Safety
2. Always disconnect and lockout the power before any physical inspection or work is performed. 3. Should one of the safety decals become damaged or illegible, contact Scott Equipment immediately for replacement. 4. Under no circumstances should any attempt be made to override the safety equipment that is supplied on this mixer. -
Page 7: Installation
1. All wiring must be performed by a qualified electrician. If problems develop with electrical components supplied by Scott Equipment contact service personnel immediately. Repairs are not to be made without written authorization from Scott Equipment. Failure to comply to this could void the manufacturer's warranty. You will be contacted by the component manufacturer with a recommended action. - Page 8 If either occur, stop the machine immediately. A damaged bearing could seize, causing serious damage to the shaft. Call your local bearing representative or Scott Equipment for replacement or service.
- Page 9 2. Tighten seals slowly until product leaking subsides. CAUTION: Do not over-tighten the seals, as this will cause undue wear and excessive friction on the main shaft. If excessive heat is noticed on the shaft or bearing, loosen the push ring and call Scott Equipment for further discussion.
-
Page 10: Tips For Operation
Tips For Operation ADJUSTABLE SCREEN CARRIAGE: Most screen carriages should be set by SCOTT EQUIPMENT and should not need any further adjustment, but if you purchased a spare screen or replacement and need to adjust, here is the procedure to follow. -
Page 11: Troubleshooting
Trouble Shooting: Problem: Production is Inadequate Possible Solutions: 1. Screen size may be too small. 2. Feed supply to the crusher is not constant. 3. Material may not be taken away from the discharge of the crusher. 4. RPM of the crusher may be increased to speed production. 5. -
Page 12: General Maintenance
Before cleaning, DISCONNECT POWER AND LOCKOUT. Remove covers where applicable for easy access. When complete, replace and properly secure covers 5. Unusual noises coming from the machine should be investigated immediately. SCOTT EQUIPMENT IS NOT LIABLE FOR DAMAGE DUE TO NEGLECT ON THE PART OF THE OPERATOR. -
Page 13: Warranty And Terms
Warranty and Terms Should any parts furnished, but not manufactured by, Scott Equipment Company fail while covered under warranty, the following should be followed: 1. Call Scott Equipment service personnel immediately. Your problem will receive prompt attention. You will be notified on what action to take. -
Page 14: Conditions Of Sale
Conditions of Sale “HAZARD CONTROL DEVICES AND EQUIPMENT: Seller furnishes those Hazard Control Devices which are listed on our quotation, acknowledgement, drawings and invoice and which may be further listed in our instruction manuals and other publications. Buyer agrees not to remove or materially alter any of these hazard control devices which are attached to or included with the equipment. - Page 15 This guarantee does not pertain to products, parts, accessories or attachments which were not manufactured by SCOTT EQUIPMENT COMPANY except to the extent of the guarantee given by the manufacturer.
- Page 16 Guarantee – Scott Equipment Company CANCELLATION: Suspension or cancellation of orders may be made only upon our written approval and on terms that will indemnify against all loss. TAXES: The amount of any sales, excise or other taxes, if any, applicable to the...
- Page 17 DOMINATOR CRUSHER PARTS LIST CUSTOMER: NEPTUNE TECHNOLOGIES MACHINE TYPE: 30x30 CRUSHER SCOTT JOB #: 13-071 MODEL #: CR30X30 CONTRACTOR: SERIAL #: 1304071 ITEM: MFG: DESCRIPTION: PART NUMBER: SUGG.* STOCK Drive assembly: Motor: MARATHON 20HP TEFC 3ph/575v/60hz W554 Reducer: DODGE Shaft mount reducer...
Need help?
Do you have a question about the CR30X30SS and is the answer not in the manual?
Questions and answers