Table of Contents
Advertisement
Controller (B-ACS-SDC-E)
I
Introduction
II
Pre-Installation
III
General Assembly
IV
Wiring
V
Configuration
Brivo Single Door
Installation Manual
Legal Disclaimers ............................................................................ 2
Introduction ..................................................................................... 4
Understand the function of the ACS-SDC-E ................................. 6
Understand ACS-SDC-E product compatibility ............................ 6
Verify client site is ready for installation ...................................... 6
Verify shipping contents ................................................................ 7
Planning the installation ................................................................ 7
Follow safety precautions .............................................................. 8
Assemble and mount ACS-SDC-E .................................................. 9
If not using PoE ............................................................................. 10
Wiring the ACS-SDC-E ................................................................... 11
Grounding the ACS-SDC-E ............................................................ 13
Powering the ACS-SDC-E .............................................................. 13
LED behavior for the ACS-SDC-E ................................................. 15
Resetting the ACS-SDC-E to factory default ............................... 15
Connecting to the ACS-SDC-E via local area network ............... 16
Verify connection of ACS-SDC-E to local area network ............ 16
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Brivo B-ACS-SDC-E
Summary of Contents for Brivo B-ACS-SDC-E
-
Page 1: Table Of Contents
Brivo Single Door Controller (B-ACS-SDC-E) Installation Manual Legal Disclaimers ................2 Introduction Introduction ..................4 Understand the function of the ACS-SDC-E ......... 6 Understand ACS-SDC-E product compatibility ......6 Verify client site is ready for installation ........6 Pre-Installation Verify shipping contents ..............7 Planning the installation .............. -
Page 2: Legal Disclaimers
The ACS-SDC-E complies with the UL294 Standard for access control units. Canada-Underwriters Laboratories (C-UL) Compliancy (CSA C22.2 No. 205) For C-UL Listed applications, the unit shall be installed in accordance with Part 1 of the Canadian Electrical Code. © 2023 Brivo Systems LLC. All rights reserved. PUB-Brivo ACS-SDC-E Installation Manual_v1.2... - Page 3 Brivo Systems LLC. The information contained within this document or within the product itself is considered the exclusive property of Brivo Systems LLC. All information in this document or within the hardware and software product themselves is protected by the copyright and/or other intellectual property laws of the United States.
-
Page 4: Introduction
Reader: The ACS-SDC-E includes the connection for one access control card reader with an optional second reader for in/out antipassback situations. Brivo Access: Brivo’s cloud based software application which enables the end user to manage his or her Brivo account. - Page 5 The following additional resources are available for the installer as well as the client. · ACS-SDC-E Data Sheet · Panel Networking Guide · Brivo ACS-SDC-E Quick Start Guide · Technical Support: 1-866-BRIVO-4-U · www.brivo.com · support.brivo.com (for non-hardware specific help) © 2023 Brivo Systems LLC. All rights reserved. PUB-Brivo ACS-SDC-E Installation Manual_v1.2...
-
Page 6: Understand Acs-Sdc-E Product Compatibility
Brivo ACS-SDC-E Installation Manual Pre-Installation Procedures Before you begin installing the Brivo control panel, perform the following tasks to ensure a safe, speedy, and suc- cessful installation. Understand the function of the Brivo ACS-SDC-E control panel The ACS-SDC-E is a one door control panel with a single access point. This control panel is considered a standalone system with internet connectivity to Brivo Access. -
Page 7: Verify Shipping Contents
Locate and check the contents of the Control Panel kit. The ACS-SDC-E kit should contain the following parts: 1 cardboard box containing the following: · The B-ACS-SDC-E unit, with its identification label on the back · An additional loose label for reference ·... -
Page 8: Follow Safety Precautions
If powered by 12V DC, the power supply must be a UL294 listed or UL 603 listed power supply. Battery capacity for loss of primary power at least zero (0) hours. © 2023 Brivo Systems LLC. All rights reserved. PUB-Brivo ACS-SDC-E Installation Manual_v1.2... -
Page 9: Assemble And Mount Acs-Sdc-E
CAT5 or greater cable strain relief. Push the ACS-SDC-E into the junction box facing inwards. iii) Attach the provided cover plate. ACS-SDC-E Mounting Diagram © 2023 Brivo Systems LLC. All rights reserved. PUB-Brivo ACS-SDC-E Installation Manual_v1.2... - Page 10 800mA Tamper When triggered, the ACS-SDC-E will generate a tamper event to Brivo Access. It will be visible in the real time event interface and can be configured to generate email notifications. Tamper for ACS-SDC-E is motion triggered. Once triggered, the ACS-SDC-E will stop after a period of time (10 to 15 seconds) with the reader at rest. In order for the tamper alarm to be audible, an OSDP reader must be attached to the ACS-SDC-E unit and the tamper alarm will sound through the attached OSDP reader.
- Page 11 WARNING: Use of 24V DC The Brivo ACS-SDC-E Single Door Controller should be powered from Power over Ethernet (PoE) or a 12V DC power supply. Do NOT use 24V as input power to the ACS-SDC-E. The only place on the ACS-SDC-E that you can connect 24V is the Normally Open or Normally Closed relay contacts.
- Page 12 The ACS-SDC-E lock relay output has both Normally Open and Normally Closed contacts for wiring depending upon your application. Lock Wiring using onboard 12V DC (normally open shown) © 2023 Brivo Systems LLC. All rights reserved. PUB-Brivo ACS-SDC-E Installation Manual_v1.2...
- Page 13 Switched Ground (Aux Output) Switched Ground output enables or disables a Ground connection. This acts as a electronic relay switch to Ground. Configure the default power as either Power-On or Default Power-Off through the Brivo Access Account Config Tool. Supervised Inputs There are three (3) Supervised Inputs: ·...
-
Page 14: If Not Using Poe
NOTE: When wiring the RS485 bus, use only twisted pair shielded wire. NOTE: Input reader must be OSDP Address 1 and output antipassback reader must be OSDP Address 2. NOTE: If needed, OSDP addressing can be performed using the Brivo programing interface (WebCLI). Ground the ACS-SDC-E When grounding the ACS-SDC-E unit, use 18 AWG or larger wire to connect the ACS-SDC-E to a suitable earth ground. -
Page 15: Led Behavior For The Acs-Sdc-E
NOTE: If the Factory Default Reset (FDR) button is released after 13 seconds or more than three seconds after the red LED is solid, a factory reset will not occur. © 2023 Brivo Systems LLC. All rights reserved. PUB-Brivo ACS-SDC-E Installation Manual_v1.2... - Page 16 Interface, you should see a recent time/date stamp in the Last Contact with Central field. NOTE: Firmware Upgrade - When first registered and connected to the Brivo cloud service, your ACS-SDC-E will automatically download and install the latest firmware. This process may take several minutes, so do not disconnect or cut power to your ACS-SDC-E during this process.
Need help?
Do you have a question about the B-ACS-SDC-E and is the answer not in the manual?
Questions and answers