Summary of Contents for InoTec inoMIX S50 S
- Page 1 Operating Manual inoMIX S50 S continuous mixer Read this entire original operating manual before starting work.
- Page 2 Thank you for trusting INOTEC. By purchasing you have opted for a quality product. If you have any suggestions or any issues, we would be delighted to hear your suggestions for improvement and your feedback. Speak to the sales representative assigned to you or, in urgent cases, contact us directly.
-
Page 3: Table Of Contents
3.7 Mixing shaft ...............................9 3.8 Noise emissions ..............................9 3.9 Operating conditions ............................9 4 Assembly and function ........................... 10 4.1 Scope of delivery inoMIX S50 S (Art.-No. 10044084) ..................10 4.2 Functionality ..............................10 4.3 Components ..............................10 4.3.1 Description of the components ............................10 4.3.1.1 Main frame with material hopper incl. - Page 4 7.2 Commissioning the inoMIX S50 S (processing bagged material) ..............23 7.2.1 Function after commissioning (processing bagged goods) ....................23 7.3 Commissioning the inoMIX S50 S (processing material from a silo) ............24 7.3.1 Function after commissioning. (Processing material from a silo) ..................24 7.4 Changing the material .............................24...
-
Page 5: General Information
In the event of a warranty claim, send the entire machine, along with the invoice, to our headquarters in Waldshut- NOTE NOTICE draws your attention to useful tips for Tiengen. effectively handling the machine. Contact our free INOTEC service hotline beforehand on +49 7741 6805 777. Page 5... -
Page 6: Warranty Claims
Danger due to misuse! Misuse of the inoMIX S50 S can lead to hazardous situations. • Never use the inoMIX S50 S continuous mixer to produce other products – such as food. • Never use the inoMIX S50 S continuous mixer outside the parameters specified in the “Technical data”. -
Page 7: Notices In The Operating Manual
• Do not reach into the rotating shaft. INOTEC GmbH and obtaining its written approval. Oth- • Do not place any objects into the rotating shaft. erwise, the operating license will become void. -
Page 8: Notices On The Machine
The unqualified operation of the • The device may only be operated via a connector protect- inoMIX S50 S may result in danger to the life and limb ed with an RCD (FI) IDh ≤ 30 mA (3). of the operating personnel, as well as damage to the •... -
Page 9: Technical Data
Chapter 3 Technical data 3 Technical data 3.3 Water measuring system 3.1 Rating plate Pressure being too low From 2 to 6 bar Pressure reducer 2.0 bar ex-works setting Solenoid valve 230 V, 50 Hz Supply line ¾ inch water pipe (to be supplied by cus- tomer) 3.4 Material hopper... -
Page 10: Assembly And Function
Chapter 4 Assembly and function 4 Assembly and function 4.3 Components 4.1 Scope of delivery inoMIX S50 S (Art.-No. 10044084) The scope of delivery is generated using the components or- dered and can be checked using the delivery note. • Frame •... -
Page 11: Motor
Chapter 4 Assembly and function 4.3.1.4 Motor The motor is attached to the main frame by a quick-release fastener. The CEE plug of the motor is connected to the top socket on the side of the switching cabinet. The metering WARNING shaft previously pushed into the main frame is connected to Water jet. -
Page 12: Motor
Chapter 4 Assembly and function 4.5 Connections 4.5.1 Power connection (400 V) DANGER Rotating shaft. Danger of death due to being pulled into the ma- chine and crushed. When the motor is running, the metering shaft ro- tates, even if the mixing pipe has been removed with the mixing shaft! •... -
Page 13: Water Fitting Connections
Chapter 4 Assembly and function 4.5.3 Water fitting connections 4.6 Operating modes The ready-mixed material can be filled into any container (bucket, wheelbarrow, etc.), or you can combine the ino- MIX S50 S e.g. with the 400 V feed pump inoBEAM F50. Connection for a water hose for cleaning the mixing pipe and mixing shaft (1), connection of the external water supply (2), connection of the mixing pipe to the water... -
Page 14: Accessories
10044102 Optional transition hood with a flexible rubber transfer bellows and with a flange Item no. (DN 250). The transition hood is attached to the material container of the inoMIX S50 S 10044126 with four eyebolts. This allows the inoMIX S50 S to be connected directly to a silo. -
Page 15: Spare Parts And Diagrams
Chapter 4 Assembly and function 4.8 Spare parts and diagrams The spare parts for the inoMIX S50 S are marked with num- bers in the following images. The individual items are de- scribed in the table under the respective diagrams. -
Page 16: Water Measuring System Spare Parts List
Chapter 4 Assembly and function 4.8.2 Water measuring system spare parts list Item Item no. Installation Name quantity 10006459 Units Needle valve, ¾“ IT 10023112 Units Solenoid valve 1/2”, 230 V, type 6213A 10006477 Units Reduction nipple, 3/4” / 1/2” ET 10006465 Units Pressure reducer D06F-1/2, with brass... -
Page 17: Metering Shaft
Chapter 4 Assembly and function 4.8.3 Metering shaft Metering shaft 30 mm gradient Item no. 10043255 (e.g. bonding and reinforcing compounds) 4.8.4 Mixing pipe inoPOWERMIX “S” with mixing shaft and mixing pipe cover Mixing pipe Item Item no. Installation Name quantity 10044030 Units... -
Page 18: Mixing Pipe Cover For Mixing Pipe Inopowermix "S
Chapter 4 Assembly and function 4.8.5 Mixing pipe cover for mixing pipe inoPOWERMIX “S” Mixing pipe cover for inoPOWERMIX “S” Mixing pipe Item Item no. Installation Name quantity 10044008 Units Mixing pipe cover for mixing pipe inoPOWERMIX “S” 10006175 Units Plastic transfer for the mixing shaft 4.8.6 Mixing shaft for mixing pipe inoPOWERMIX “S”... -
Page 19: Drive Unit
Chapter 5 Transport and storage 4.8.7 Drive unit Motor Item Item no. Installation Name quantity 10044083 Units Complete drive unit 10044080 Units Spur gear motor, 2.6 kW, 400 V 10043829 Units Complete motor flange (incl. items 6, 7, 8 and 9) 10039955 Units Motor flange without attachments... -
Page 20: Transport And Storage
2. Have the transport damage confirmed by means of the driver’s signature. 3. Send copy damage report transport company another Inotec GmbH. 4. And clarify the possible ways in which the damage could be remedied with one of our service centres (see second last page) Page 20... -
Page 21: Installation
6.3 Assembling the mixing pipe and mixing shaft eration. • Only install the inoMIX S50 S on a level, horizontal sur- 1. Assemble the mixing pipe by using both eccentric fas- face. -
Page 22: Installing The Water Measuring System
Chapter 7 Commissioning 2. Use a connection cable with CEE plug 5 x 16 A. 3. Make sure that the cross-section of the supply cable is 2.5 mm 4. Connect the supply cable to the unit plug below the WARNING main switch. -
Page 23: Commissioning
7 Commissioning 7.2 Commissioning the inoMIX S50 S (processing bagged material) 1. Only connect the inoMIX S50 S to a proper power dis- tributor in a building with a 30 mA residual current cir- cuit breaker. 2. Use a connection cable with CEE plug 5 x 16 A. -
Page 24: Commissioning The Inomix S50 S (Processing Material From A Silo)
7.6 Change of location on the construction site The inoMIX S50 S is equipped with two wheels. By lifting the mixing pipe connected to the mixer, the inoMIX S50 S 7.3 Commissioning the inoMIX S50 S (processing ma- can be easily moved around the construction site. -
Page 25: Operation, Use
1. If you notice any deviations in operating behaviour, put NOTE Always carry out this cleaning process be- the inoMIX S50 S out of operation immediately. fore longer breaks in work (> 0.5 hours). Do not oper- 2. Ensure that the damage and/or defects which led to the ate the mixing pipe forcibly from the outside (e.g. -
Page 26: End Of Work
Chapter 9 Cleaning & decommissioning 8.5 End of work 8.5.4 Dismantling the motor and metering shaft 1. Remove the motor by opening the quick-release fasten- er that connects the motor to the main frame. 8.5.1 Switch off the machine (processing bagged 2. -
Page 27: Cleaning & Decommissioning
Chapter 9 Cleaning & decommissioning 9 Cleaning & decommissioning 9.1 Cleaning process 1. Stop filling with bagged goods in sufficient time. DANGER Rotating shaft. 2. Empty the material hopper of the main frame and the Danger of death due to being pulled into the ma- mixing pipe. -
Page 28: Mixing Pipe And Mixing Shaft With Mixing Pipe Cover
Portable ma- 2. Open both eccentric fastenings to separate the mixing chines – such as the inoMIX S50 S – must be subjected pipe from the main frame. to an annual electrotechnical inspection in accordance with the Implementing Regulation for Electrical Installa- tions and Equipment (DGUV V3). -
Page 29: Dirt Trap Sieve In The Water Inlet
Electrical inspection (DGUV Once a year V3) by a qualified electrician or (Mandatory, stipulated 30 mm gradient, e.g. Item no. at an INOTEC service centre by DGUV V3) for bonding and basecoat mortars 10043255 The dirt trap sieve in the water Daily... -
Page 30: Faults, Causes And Solutions
Chapter 11 Faults, causes and solutions 11 Faults, causes and solutions The inoMIX S50 S is designed to ensure its trouble-free op- eration. However, should a fault occur, please follow the instructions below on analysing, checking and remedying the fault or contact the Inotec Service team (see the address list for INOTEC service centres at the end of the document) or call the INOTEC service hotline on: +49 7741 6805 777. - Page 31 Chapter 11 Faults, causes and solutions The faults listed below feature recommendations as to who is authorised to rectify the fault. Symptom Potential cause Check / solution Personnel qualification If the machine will not Power supply is • Check the power supply (power distribution points, socket, Machine operator start.
-
Page 32: Dismantling And Disposal
• Send the metal to a recycling facility. • Dispose of the inoMIX S50 S via a scrap metal dealer or your local scrap metal collection point. Your used INOTEC equipment will be taken back by us and disposed of in an environmentally conscious manner. -
Page 33: Systems
EC Directive 2006/42/EC. This declaration will become void in the event of any modification made to the machine without our approval. Designation of the unit: inoMIX S50 S Machine model: Continuous mixer... -
Page 34: General Terms Of Business Of The Company Inotec Gmbh
In the case of simple negligence on the part of INOTEC GmbH, this is a fixed amount totalling 0.5% for each full week of the IV. The customer hereby assigns to INOTEC GmbH the purchase price, wages... -
Page 35: Circuit Diagram For Inomix S50 S
Chapter 13 Systems 13.3 Circuit diagram for inoMIX S50 S Page 35... - Page 36 Page 36...
-
Page 37: Order Form
Chapter 14 Order form 14 Order form Fax to: +49(0)7741-6805-665 Delivery address Invoice to Name of the ordering party Consultation from Date Number Item no. Item name Our General Terms of Business, Delivery and Payment apply. The customer has been made aware of these terms and agrees to the application of the same. -
Page 38: Index
Responsibility of the operator ...........8 Disclaimer ................5 Dismantling and disposal ..........32 Displays and controls .............11 Safety ................6 Scope of delivery inoMIX S50 S (Art.-No. 10044084) ..10 EC declaration of conformity ..........33 Spare parts and diagrams ..........15 Symbol explanation ............5 End of work ..............26 Exercising claims ..............5... -
Page 39: Locations
Chapter 16 Locations 16 Locations Your sales partner (English language) INOTEC GmbH (Headquarter) Daimlerstraße 9-11 79761 Waldshut-Tiengen Germany Mobile: +49 160 94925237 m.fechtig@inotec-gmbh.com Wherever you are, we’re there, too. Page 39... - Page 40 Accessories & Waste water Floor Compressed air / dehumidifiers / Spare parts systems processing compressors high-pressure cleaners Power tools / electrical appliances INOTEC GmbH • Daimlerstraße 9-11 • D-79761 Waldshut-Tiengen • Tel.: +49 77 41 / 68 05-0 • www.inotec-gmbh.com...
Need help?
Do you have a question about the inoMIX S50 S and is the answer not in the manual?
Questions and answers