Related Manuals for NCR VOYIX 7772-K168
Summary of Contents for NCR VOYIX 7772-K168
- Page 1 Wireless Card and Antenna (Port C) Kit Instructions 7772-K168 Issue B Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
- Page 3 Table of Contents Copyright Wireless Card and Antenna (Port C) Kit Contents Installation Procedure Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 4 Revision Record Issue Date Remarks Jun 2020 First Issue Dec 2021 Added Warning statement Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 5 Wireless Card and Antenna (Port C) This kit provides a Wireless Card and Antenna for Port C of the NCR CX7 All-in-One POS (7772) or NCR CX5 All-in-One POS (7773). Kit Contents Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 6 Remove the two (2) screws that secure the Cable Cover to the Back Cover. b. Rotate and unhook the Cable Cover from the Back Cover. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 7 Remove the Ethernet Cable from the Cable Management Hook then disconnect the Cable. 4. Loosen the two (2) captive screws that secure the Back Cover to the Display. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 8 5. Rotate the Back Cover away from the Display and unhook the Back Cover Tabs. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 9 6. Insert a flat screw driver in the slot to unsnap the Peripheral Filler Plate from Port C of the display housing. 7. Insert the Wireless Card into the connector. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 10 8. Secure the Card with a screw. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 11 9. Route the first Antenna Cable through the port opening located as shown and pull the Cable completely through. Note If present, remove the protective cover from the Micro Coax Connector. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 12 10. Remove the adhesive liner from the Antenna and place the Antenna on the location marked “1” on the display housing. Ensure the solder joint of the Antenna is within the opening. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 13 11. Route and secure the Antenna Cable under the Cable Management Hooks as shown. Note Route the Cable above the upper edge of the Speaker. 12. Connect the first Antenna Cable to Connector 1 (Aux) of the Wireless Card. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 14 13. Route the second Antenna Cable through the port opening located as shown and pull the Cable completely through. Note If present, remove the protective cover from the Micro Coax Connector. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 15 14. Remove the adhesive liner from the Antenna and place the Antenna on the location marked “2” on the display housing. Ensure the solder joint of the Antenna is within the opening. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 16 15. Route and secure the Antenna Cable under the Cable Management Hooks as shown. Note Route the second Cable below the bottom edge of the Speaker. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.
- Page 17 17. Hook the Peripheral Filler Plate into the display housing and snap into place. 18. Reinstall the Display Back Cover. 19. Reconnect the 180-degree USB-C Cable and Ethernet Cable. 20. Reinstall the Cable Cover. Confidential and proprietary information of NCR Corporation. Unauthorized use, reproduction and/or distribution is strictly prohibited.