Advertisement
Quick Links
READ CAREFULLY
BEFORE INSTALLATION
WARNING!! Do not install Hood Scoops or other Body Parts directly Over Wrapped
areas. Before installation of the parts , you must leave at least a 1/4" (6mm) perimetral
clearance "Free from Vinyl" surrounding the part, before Part installation.
WARNING!! Do not install Hood Scoops Over Vinyl or Over Plastic Stripes on the Hood: 3M
Adhesive Tape and PUR Adhesive must always be in contact with the Sheet Metal of the vehicle.
WARNING!! Rust Prevention Oils and other Petrol Based Anti Rust Treatments for Vehicles
may affect 3M´s Double Adhesive Tape and Polyurethane Adhesive performance!
DATE: 07.01.20
VERSION 0
WASH BEFORE
INSTALLING
WE RECOMMEND
2 PERSONS FOR
INSTALLATION
www.airdesignusa.com
Tacoma 2016 - 2022
INSTALLATION MANUAL
SUPER-BOLT FENDER FLARES SET
PART # : 1109NNTJTO02A10
AFTER INSTALLING
DOT NOT WASH CAR
24 hrs
PG. 1
Advertisement
Related Manuals for Air Design 1109NNTJTO02A10
Summary of Contents for Air Design 1109NNTJTO02A10
- Page 1 Tacoma 2016 - 2022 INSTALLATION MANUAL SUPER-BOLT FENDER FLARES SET PART # : 1109NNTJTO02A10 WASH BEFORE READ CAREFULLY INSTALLING BEFORE INSTALLATION WARNING!! Do not install Hood Scoops or other Body Parts directly Over Wrapped areas. Before installation of the parts , you must leave at least a 1/4” (6mm) perimetral clearance “Free from Vinyl”...
- Page 2 Tacoma 2016 - 2022 INSTALLATION MANUAL TOOLS ¼” 10mm CHECK LIST Already installed in the part ITEM DESCRIPTION DRAWING AMOUNT 36 PCS *SUPER-BOLTS RUBBER STUDS 36 PCS *STAINLESS SUPER-BOLT M6x14 8 PCS *STAINLESS LOCKNUT M6 PHILLIPS - HEX HEAD SEMS TAPPING SCREW M 6.3 X 25 M 16 M 4 PCS WASHER / 10 M 33 FT...
- Page 3 Tacoma 2016 - 2022 INSTALLATION MANUAL The ideal temperature range of the part and the vehicle when installing must be 16ºC (60ºF) to 40ºC (104ºF), this guarantees a correct assembly. WASH WITH WATER, DETERGENT AND FRONT RIGHT & LEFT FLARE SOFT CLOTH OR SPONGE ONLY IF YOUR TACOMA HAS OE FENDER FLARES INSTALLED REMOVE SCREWS...
- Page 4 Tacoma 2016 - 2022 INSTALLATION MANUAL SECURE THE PART 10mm MARK SILHOUETTE AND SUPER-BOLTS POSITIONS HASH MARKS DRAW CENTER HASH MARK WITH GREASE PENCIL AT CENTER, BOTH SIDES, ON EACH SUPER-BOLT AND SHEET METAL. THIS WILL ENSURE WHEEL FLARE WILL BE CENTERED TO GREASE PENCIL OUTLINE.
-
Page 5: Application Area
Tacoma 2016 - 2022 INSTALLATION MANUAL UNSCREW REMOVE 10mm APPLICATION AREA INNER VIEW WARM SURFACES WITH HEAT GUN IF SURFACE TEMPERATURE IS TOO COLD. ALIGN WHEEL FLARE TOP EDGE WITH THE GREASE PENCIL HASH MARKS AND PLACE. DATE: 07.01.20 PG. 5 www.airdesignusa.com... - Page 6 Tacoma 2016 - 2022 INSTALLATION MANUAL WE RECOMMEND SECURE THE PART 2 PERSONS FOR 10mm INSTALLATION APPLY PRESSURE ON EACH SUPER-BOLT UNSCREW 10mm REMOVE SUPER-BOLTS (B) REMOVE ONLY THE ONES WITH RUBBER STUD PG. 6 Mexico (+52) 55 5393 6636 / USA +1 (760) 435 0095...
- Page 7 Tacoma 2016 - 2022 INSTALLATION MANUAL SUPER-BOLT INSTALLATION PRESS SUPER-BOLTS STUDS (A) ATTENTION FULL SURFACE CONTACT IS CRITICAL FOR GOOD ADHESION PERFORMANCE. ALWAYS APPLY FIRM PRESSURE WHEN MOUNTING ADD ON PARTS AND TAPES. 58 - 72 PSI SUPER-BOLT STUDS PRESSURE POINTS DATE: 07.01.20 PG.
- Page 8 Tacoma 2016 - 2022 INSTALLATION MANUAL SECURE THE PART PLACE SUPER-BOLTS STUDS 10mm PLACE SUPER-BOLTS APPLY LOCTITE THREADLOCKER TO SUPER-BOLTS THREAD DON’T FORCE ATTENTION THE TURN ONCE IT HAS STOPPED ¼” CLEAN OFF GREASE PENCIL MARK PG. 8 Mexico (+52) 55 5393 6636 / USA +1 (760) 435 0095...
- Page 9 Tacoma 2016 - 2022 INSTALLATION MANUAL ONLY IF YOUR TACOMA HAS OE REAR LEFT & RIGHT FENDER EXTENSION FENDER FLARES INSTALLED REMOVE SCREWS REMOVE MUD GUARDS 10mm REMOVE SCREWS REMOVE ORIGINAL FLARES 10mm DATE: 07.01.20 PG. 9 www.airdesignusa.com...
- Page 10 Tacoma 2016 - 2022 INSTALLATION MANUAL SECURE THE PART 10mm MARK SILHOUETTE AND SUPER-BOLTS POSITIONS HASH MARKS DRAW CENTER HASH MARK WITH GREASE PENCIL AT CENTER, BOTH SIDES, ON EACH SUPER-BOLT AND SHEET METAL. THIS WILL ENSURE WHEEL FLARE WILL BE CENTERED TO GREASE PENCIL OUTLINE.
- Page 11 Tacoma 2016 - 2022 INSTALLATION MANUAL UNSCREW REMOVE 10mm APPLICATION AREA INNER VIEW ALIGN WHEEL FLARE TOP EDGE WITH THE GREASE PENCIL HASH MARKS AND PLACE. DATE: 07.01.20 PG. 11 www.airdesignusa.com...
- Page 12 Tacoma 2016 - 2022 INSTALLATION MANUAL SECURE THE PART WE RECOMMEND 2 PERSONS FOR INSTALLATION 10mm UNSCREW APPLY PRESSURE ON EACH SUPER-BOLT 10mm REMOVE REMOVE SUPER-BOLTS (B) ONLY THE ONES WITH RUBBER STUD ¼” PG. 12 Mexico (+52) 55 5393 6636 / USA +1 (760) 435 0095...
- Page 13 Tacoma 2016 - 2022 INSTALLATION MANUAL SUPER-BOLT INSTALLATION PRESS SUPER-BOLTS STUDS (A) ATTENTION FULL SURFACE CONTACT IS CRITICAL FOR GOOD ADHESION PERFORMANCE. ALWAYS APPLY FIRM PRESSURE WHEN MOUNTING ADD ON PARTS AND TAPES. 58 - 72 PSI SUPER-BOLT STUDS PRESSURE POINTS DATE: 07.01.20 PG.
- Page 14 Tacoma 2016 - 2022 INSTALLATION MANUAL SECURE THE PART PLACE SUPER-BOLTS STUDS (A) 10mm PLACE SUPER-BOLTS (B) APPLY LOCTITE THREADLOCKER TO SUPER-BOLTS THREAD ATTENTION DON’T FORCE THE TURN ONCE IT HAS STOPPED ¼” CLEAN OFF GREASE PENCIL MARK INSTALLED PARTS PG.