Forte F2412MVD650SS Installation Manual

Forte F2412MVD650SS Installation Manual

24" microwave drawer

Advertisement

Quick Links

SPECIAL WARNING

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord
with the stated clearances and dimensions on pages 2 and 3. See Figure 1.
UNPACKING YOUR MICROWAVE DRAWER
·
Remove all packing materials from inside the
Microwave Drawer.DO NOT REMOVE THE
WAVEGUIDE COVER,which is located on the top
of the Microwave Drawer.
·
Remove the feature sticker, if there is one .Check
the drawer for any damage, such as misaligned or
bent drawer, damaged drawer seals and sealing
surfaces, broken or loose Microwave Drawer
guides and dents inside the cavity or on the front
side of the drawer. If there is any damage, do not
operate the Microwave Drawer and contact your
dealer or a FORTE AUTHORIZED SERVICER.
IMPORTANT NOTES TO THE INSTALLER
·
Read all of the Installation Manual before
installing the Microwave Drawer.
·
Remove all packing material before connecting
the electrical supply.
·
Observe all governing codes and ordinances.
·
Be sure to leave these instructions with the
consumer.
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for
future
reference.
·
As when using any microwave oven generating
heat, there are certain safety precautions you
should follow. These are listed in the Operation
Manual. Read all and follow carefully.
24" Microwave Drawer
F2412MVD650SS
INSTALLATION MANUAL
·
Be sure your Microwave Drawer is installed and
grounded properly by a qualified installer or
service technician.
I
MPORTANT SAFETY INSTRUCTIONS
WARNING
if the information in this manual is not
followed exactly, a fire or electrical shock may result
that could cause property damage, personal injury or
death.
WARNING
To reduce the risk of tipping ,the
Microwave Drawer must be secured by a properly
installed Anti-Tip block.
·
This Microwave Drawer must be electrically
grounded in accordance with local codes.
·
Make sure the wall coverings and the cabinets
around the Microwave Drawer can withstand the heat
generated by the Microwave Drawer.
WARNING
Never leave children alone or
unattended in the area where a Microwave Drawer
is in use. Never leave the drawer open when the
microwave is unattended.
WARNING
Stepping ,leaning or sitting on the drawer
may result in serious injuries and can also cause
damage to the Microwave Drawer.
·
Do not use the Microwave Drawer as a storage
space .This creates a potentially hazardous
situation.
·
Check that the time-of-day is in the display. IF not,
touch Stop/Clear to prevent unintended use.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F2412MVD650SS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Forte F2412MVD650SS

  • Page 1 If there is any damage, do not Microwave Drawer must be secured by a properly operate the Microwave Drawer and contact your dealer or a FORTE AUTHORIZED SERVICER. installed Anti-Tip block. · This Microwave Drawer must be electrically IMPORTANT NOTES TO THE INSTALLER grounded in accordance with local codes.
  • Page 2 CLEARANCES AND DIMENSIONS · · Dimensions that are shown in Figure 1 must be Check location where the Microwave Drawer will used. Given dimensions provide minimum be installed for proper electrical supply · clearance. Locate electrical outlet in the shaded Your oven can be built into a cabinet or wall by area in the upper left-hand corner of the cutout.
  • Page 3 ANTI-TIP BLOCK ELECTRICAL OUTLET Su gge ste d el ect ric al out let loc ati on Anti Tip block 4 '' Figure 4 Figure 3 NORMAL INSTALLATION STEPS The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp. or more protected electrical supply. It is ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS To reduce the risk of tipping of the drawer, the Anti-Tip recommended that a separate circuit serving only this...
  • Page 4 DRAWER INSTALLATION Mounting flange Screws Figure 5 1. Place the drawer adjacent to the wall or cabinet opening.Plug the power supply cord into the electrical outlet. 2. Carefully guide the drawer into the prepared opening. Avoid pinching the cord between the oven and the wall. 3.

Table of Contents