Table of Contents
Advertisement
Quick Links
Handbook version no. 20190903
NOEL MACHINERY
Industrial Shed, No.6/5, MSREC Road, Gokula, Mathikere, Bangalore-560054.
1st floor, 220 Zhongxing Road, Dalingshan Town, Dongguan City, Guangdong Province, China
Dongguan Easytech Automation Mechanical and Electrical Equipment Co., Ltd.
Tel: +86 135 3727 1735
Manual of Hydraulic Riveting Machine ETJSTY-818
www.noelmachinery.in
Advertisement
Table of Contents
Summary of Contents for NOEL NM-620
- Page 1 Handbook version no. 20190903 NOEL MACHINERY Industrial Shed, No.6/5, MSREC Road, Gokula, Mathikere, Bangalore-560054. 1st floor, 220 Zhongxing Road, Dalingshan Town, Dongguan City, Guangdong Province, China Dongguan Easytech Automation Mechanical and Electrical Equipment Co., Ltd. Tel: +86 135 3727 1735 Manual of Hydraulic Riveting Machine ETJSTY-818 www.noelmachinery.in...
- Page 2 Handbook version no. 20190903 Model No.: ETJSTY-818 Brief description: Detail parameters and functions: -YY- full hydraulic drive - Maximum output pressure -500C-C frame throat depth 500mm (Standard) -650C-C frame throat depth 650mm (Optional) Detail parameters and functions: * throat high 380 mm * working stroke 110mm, adjustable stroke 60mm * upper die is with guider to prevent the upper die from rotating...
- Page 3 Handbook version no. 20190903 NM-620 NM-826 6 ton 500 mm throat depth 8 ton 650mm throat Main Motor 2.2Kw Main motor 3.7kw www.noelmachinery.in...
-
Page 4: Safety Warning
Handbook version no. 20190903 ===================================== 安全警告 客户如需自制上模时，上模的安装部位尺寸一定要按图纸要求做，否则安全 防护会失效或损坏安全开关。 压铆机上模建议选用材料Cr12加工，加工后需热处理55°-60° Safety Warning If customers make the upper die by themselves, the size of the mounting part of the upper die must be made according to the drawing. Otherwise the safety protection will fail or damage the safety switch. It is recommended to use material Cr12 to process the die on the riveting press. - Page 5 Handbook version no. 20190903 Oil Supplement Open the upper left cover to refuel the tank. Please add 46# anti-wear hydraulic oil. The capacity is 55-60L. The oil level can be seen through the transparent window of the front cover. The minimum oil level is about above the mark 60 (4 small barrels) upper left cover transparent...
-
Page 6: Main Power Connection
Handbook version no. 20190903 ========================================================================== 接总电源说明 本款机型电机功率为3.75KW 请使用(3+1; 三根相线，一根地线)2.5平方线电源线 当相序接错时，旋转总电源开关接通电源，电控箱内的相序控制器工作指示 灯不亮，按下启动按钮设备不能启动，这时需更换相序（更换任意两根相线 就可以调换相序）。 当相序接正确时，旋转总电源开关接通电源，电控箱内的相序控制器工作指 示灯会亮红灯，按下启动按钮设备就可以启动。 Main Power Connection The motor power is 3.75kw -Please use (3 + 1, three phase lines, one ground line)2.5 square power line -If the phase sequence is misconnected, when you turn the main power switch to connect the power, the working indicator light of the phase sequence controller in the electric cabinet won’t be on, and the device cannot start when press the start button. -
Page 7: Power On/Off
Handbook version no. 20190903 Power on/off 1. Turn on the main power switch, and the corresponding power indicator will be lit. 2. Check whether the oil pump stop button is in a reset state. If there is no reset, please reset first. 3. -
Page 8: Pedal Operation
Handbook version no. 20190903 再次一直踩住向下脚踏，整个压铆过程才能完成。 工作时，如果需要模具向上运动，请踩住向上脚踏开关。 二、 点踩模式 工作时，脚只需踩一下向下脚踏，整个压铆过程会自动完成。 工作时，如果需要模具向上运动，请踩住向上脚踏开关。 Pedal Operation There are two tap operation modes, which can be selected on the panel according to the actual operation needs. 1. Continuous pedal mode When working, step on the downward pedal so that the whole process of riveting can be completed. -
Page 9: Safety Protection
Handbook version no. 20190903 Safety Protection (Safety warning: please do not place any part of your body between the upper and lower molds when operating the machine. 1. Conductive mode (please refer to tap operating instruction for pedals) 1). When the workpiece is conductive, turn the switch to conductive mode. 2). - Page 10 Handbook version no. 20190903 Referring to the control panel, turn clockwise to increase the pressure holding time and turn counterclockwise to reduce the pressure holding time. When upper mold and lower mold press the workpiece, 1-5 seconds of pressure holding time can be set according to the need. When the upper mold and lower mold reach the pressure holding time, it will return automatically.
-
Page 11: Pressure Adjustment
Handbook version no. 20190903 cover). At this time, the return position should be reduced appropriately. 压力调整说明 参照压力调整面板，松开锁紧螺母，顺时针加大压力，逆时针减小压力； 压力调整完成后请锁紧螺母。 调压手柄后面的锁紧螺母不能卸下。当压力调整的太小时，有可能会造成调 压手柄掉落，请立即安装上。本机型建议最大使用压力在175以内。 （客户进行抽牙时，压力调到0-50之间，把保压时间尽量调小） Pressure Adjustment Referring to the pressure adjustment panel, loosen the lock nut, turn clockwise increase the pressure, and turn counterclockwise to decrease the pressure. - Page 12 Handbook version no. 20190903 Stroke Limit Adjustment Tip: use only when necessary.(Press rather soft materials or for other use) Note: when using limit, the pressure should be controlled below 100. 1. Loosen the lock nut and the limit nut can be rotated to adjust the downward position.
- Page 13 Handbook version no. 20190903 主电路控制原理图 安全警告：当需检查或维修电路时，请先关闭总电源 Main Circuit Control Schematic Diagram Safety warning: when you check or repair the circuit, please turn off the main power. www.noelmachinery.in...
-
Page 14: Control Panel Instruction
Handbook version no. 20190903 Control panel instruction Press-hand preventing switch (when the equipment is only powered on, not running, the upper mold and lower mold doesn’t contact, the machine will not work when the light is on. Push up the mold with hand, release,and see whether the light will be off.If the light is off, fault can be eliminated.The fault is that the safety switch is not reset.) Solenoid valve upward (mold upward solenoid valve working indicator) - Page 15 Handbook version no. 20190903 Counter Laser switch Conductive/non-conductive switch (Please refer to “Safety protection instruction”) Rhythmic tap/continuous tap (Please refer to “Tap operation mode instruction”) AC 24V input www.noelmachinery.in...