Summary of Contents for Lumber Jack DHB1700
- Page 1 SAFETY AND OPERATING MANUAL DEMOLITION HAMMER BREAKER DHB1700 O RIGINAL INSTRUCTIONS DHB1700...
-
Page 2: Table Of Contents
Closely observe all safety information in these instructions! General Power Tool Safety Warnings………………………………….…..01 Sy mbols & Tech Data.....……….…………………………………….………05 Machine Details ........……….…………………………….….06 Op eration…………………………………………………………………………………..07 Maintenance ....……………………………..……………………………..08 Lum berjack Guarantee………….…………………………………………………….10 De claration of Conformity……………………………………………………………12 Pa rts List…………..………………………………………………………………………...13 Pa rts Diagram………………………………………………………………………………15 DHB1700... -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. DHB1700... - Page 4 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. DHB1700...
- Page 5 J) Do not leave the tool unattended when it is SEATED IN THE HEX CHUCK before starting the job plugged into an electrical outlet. Turn off the in hand. tool, and unplug it from its electrical outlet before leaving. DHB1700...
- Page 6 To red uce vibration, maintain the tool as greater the capacity of the cord. explaine d in this manual. If any abnormal e) When using a cable reel, always unwind the vibration occurs, stop use immediately. cable completely. DHB1700...
-
Page 7: Sy Mbols & Tech Data
SYMBOLS AND TECH SPEC Danger! – Read the operating Caution! Wear safety goggles. instructions to reduce the risk of injury. Caution! Wear ear defenders. The impact of noise can cause damage to hearing. Caution! Wear a dust mask. 0 - 1900bpm DHB1700... -
Page 8: Machine Details
MACHINE DETAILS Fig. 1 30MM HEX CHUCK ON/OFF TRIGGER LOCK-ON BUTTON AUXILIARY HANDLE OIL CAP POWER CABLE 6a/6b. ANTIVIBRATION CONTROL DEVICE Fig. 2 Fig. 3 Fig. 4 DHB1700 01 01 01 01... -
Page 9: Op Eration
Insert the chisel into the chuck and push it in > as far as possible. Pull out the locking bolt (a) as far as possible, > turn it through 180° and release it to lock the chisel into the chuck. DHB1700... -
Page 10: Maintenance
OPERATING / MAINTENANCE Maintenance WARNING! WARNING! Hold electric tools by their insulated handles whenever there is the possibility of touching Switch off the tool and disconnect the power hidden wires or the tools own power cord while before cleaning and maintenance – risk of using them. - Page 11 3. Eliminate use of extension cord. If an extension cord. extension cord is needed, use one with the proper diameter for its length and load. See Extension Cords in GROUNDING section. DHB1700...
-
Page 12: Lumberjack Guarantee
This letter should be then sent with proof DHB1700... - Page 13 This Guarantee is offered as an extra benefit and does not affect your statutory rights as a consumer. 4. Notice This Guarantee applies to all product purchased from an Authorised Dealer of Lumberjack within the United Kingdom. Terms of Guarantee may vary in other countries. DHB1700...
-
Page 14: Declaration Of Conformity
Old Heat h Road, Wolverhampton, WV1 2RP. Declare that the product: Designation: DEMILITION HAMMER BREAKER Model: DHB1700 Complies with the following Directives: 2008 No. 1597 The Supply of Machinery (Safety) Regulations 2008 2016 No. 1091 The Electromagnetic Compatibility Regulations 2016 2012 No. -
Page 15: Parts List
Parts List DHB1700... - Page 16 Parts List DHB1700...
-
Page 17: Parts Diagram
Parts Diagram DHB1700...
Need help?
Do you have a question about the DHB1700 and is the answer not in the manual?
Questions and answers