Safe Fleet NH16v2 Quick Installation Manual

Basic NVR configuration (continued)
Step 5. Alarms
From the Configuration menu, select Alarms & I/OAlarms.
Alarm: Alarms 1 and 2 can be triggered by an event/alarm button. AlarmC
is triggered from a hardware input (ALM C on the Video breakout harness).
Alarms 1-4 can also come from Signals or features such as speed or GPS.
Pre Alarm: Optionally, select a time period prior to an alarm being triggered
where recorded video and metadata are included with protected alarm data,
which won't be overwritten. For more information, see Recording Settings
(Advanced) in the NH16v2 Install and Config Guide.
Duration: Set the Duration for how long the NVR will record video flagged as
an alarm for each alarm input.
Input: Applies to Alarm1, Alarm2, and AlarmC only. Choose N.O. (Normally
Open), N.C. (Normally Closed), or N.H. (Normally High) depending on the
switch type used.
Speed (frames/second), Quality, and Resolution: For each alarm, select
higher settings for better video while the alarm is recording.
Important: If Encode Perf. is below 0, adjust Speed, Quality, or Resolution
settings until the value is at or above 0. Note that Speed, Quality, and
Resolution settings are only adjustable for specific camera/device
types. For details, see the NH16v2 Install and Config Guide.
Audio: When audio is normally disabled, set ON to enable audio for the Alarm
Duration period.
Click Back twice to save settings and return to the Configuration menu, then
click Network.
Step 7. System Step 8. Load Config File, Format Drive
Password Enable: Leave OFF unless instructed
otherwise. Store Current Configuration: Select USB Device as the file-saving destination. Plug a USB
memory device into the front of the NVR. Click Store to save the file on the USB memory device.
Password: If enabled, this password is required for non-
Admin users to access the local NVR UI. Load: For details on uploading configurations to the recorder, see "NVR Configuration Uploads"
in the NH16v2 Installation and Configuration Guide.
Audio Output Channel: Select the audio channel that will
be available from the audio RCA port on the front of the Update: Delivers a firmware update to the recorder or a connected IP camera from an image file
NVR. stored on a USB device. Select DVR or IPC, then click Update and navigate to the image file:
Diagnostic Indicator: If installing an RGY Button or RGY
Illuminator, select which one.
Language: Select the language for the NVR UI.
Scheduled Reboot/Reboot Now: Configure a time-of-day
Format: Format the hard drive and SD card (if installed) when the configuration is complete and
for the recorder to reboot, or reboot immediately. tested and before final delivery of the installation to the customer.
Click Program Update.
Click Back twice to save settings and return to the Configuration menus.
Advanced Configuration Options
Alarms & I/OSignals: configure signal inputs and the actions they generate.
Alarms & I/OSpeed: record vehicle speed or trigger notifications for excessive speed.
NetworkUser Levels: create NVR user logon profiles and assign passwords to enable remote access with various permission levels.
For more information about these settings, please see the NH16v2 Installation and Configuration Guide (700-1300) on the Safe Fleet Community Web site.
Warranty and Support
For full warranty information, visit www.seon.com/documents/Seon-Warranty.pdf
Information is subject to change without notice.
Please visit the Safe Safe Fleet Community at https://community.safefleet.net for the latest product details and full installation instructions.
Step 6. Network
From the Configuration menu, select Network  IP Addresses  Front.
Setting Type: Leave at default Static IP setting.
IP address: used to communicate with the NVR over the network via a
laptop for installation and configuration purposes. Leave at default setting
unless instructed by the customer.
HTTP Port: typically, leave set to 80 unless instructed by IT personnel.
Notes:
If Smart-Reach Mobile Wi-Fi equipment or a Smart-Reach Cellular
modem is installed, click Network  IP Addresses  Wifi/Modem to
configure communication parameters. For more information, see the
NH16v2 Install and Config Guide and the Smart-Reach documentation
available on the Safe Fleet Community.
If the IP information is changed and saved in a configuration file
for upload to other NVRs, their settings will have to be updated as
well. For more information, see "NVR Configuration Uploads" in the
NH16v2 Install and Config Guide.
If the system uses Commander or Depot Manager: contact Technical
Support for assistance with setup.
Click Back to save settings and return to the Configuration menu, then
click System.
DVR: The device reboots when updates are done.
IPC: Click a numbered tab at the top of the screen to update firmware on the camera
connected to the selected port, then click Update.
Technical Support phone - 1.844.899.7366
Email - PTsupport@safefleet.net
NH16v2 NVR System Quick Installation Guide
This Quick Installation Guide is a basic install and setup reference for the recorder. Review it completely before proceeding. The NS18POE16
network switch is compatible with NH16v2. Third-party switch gear is not supported. Refer to the 16-Port Network Switch Installation Guide,
(part #700-1156) for more information. Information is subject to change without notice. Please visit the Safe Fleet Community at
https://community.safefleet.net for the latest product details and full installation instructions.
Typical System Setup:
The NH16v2 supports a maximum of 16 channels (12 channels without the network switch):
16 IP Cameras from the
NS18POE16 Network Switch
1x2 Microfit Alarm Input (ALM C)
ALARM2 G-SENSOR
POE04
POE01 MODEM
GPS
POE03
POE02G WIFI USB
Network Switch
4 IP Cameras (if Network Control Cable
060-0656
Switch not installed)
Optionally connect... To...
PoE Injector Kit ACC PWR
RGY Button* Adapter Harness (1x5
2
Microfit Connector)
Smart-Reach (Wi-Fi)* WIFI Input
3
Smart-Reach Cellular Modem* MODEM Input
3
Laptop LAN Input (front)
Portable Video Monitor* VIDEO OUT (front)
4
External G-Sensor G-SENSOR Input
Alarm Switch ALARM 2 Input
SD Card* 5 SD Card Slot (front)
 WARNING: Cable and harness slack
Ensure cables and harnesses have slack and can move
freely with the recorder without being pulled to the side
or away from the connector. A 4-inch diameter loop is
normally sufficient.
 WARNING: Noise suppression
Do not use the output of a noise suppression solenoid
as a recorder ignition or power source. If no true ignition
or power source can be readily found, consult the bus
schematic bus or manufacturer to locate a proper source.
Notes (*)
1. Vehicle speed and location tracking require the GPS antenna
(part # ANT-G6-SM, 19.6ft/6m cable).
2. The RGY Button is optional, and requires the WT2 adapter
harness and the RGY extension harness (part# 060-1197).
3. An optional Smart-Reach Wi-Fi bridge or Smart-Reach Cellular
modem can be connected to the rear panel WIFI/MODEM
© Safe Fleet | 2023
8 Std. Resolution and/or High Definition Cameras
Signal Input (SIG)
Video Breakout Harness
:
VBH-8D-2SA-M
2-conductor
CAMERAS/ALARMS
ACC PWR
Expansion
20 ft./6.1m
POWER
Harness:
060-1059 Power harness: 060-1136
1A
3 wires
Adapter
Harness* 2
20A
2x3 Microfit
Rear Vision System (Optional)
1x4 Microfit
Reserved
Harness WT2 sup-
DIGITAL OUTPUT (Optional)
ports RGY button
and extn. harness
pkg. HEDM20 Blue - Active H (12V 150mA source)/
2 wires
Active L (ground 350mA sink)
Black - Ground
WAKE (Optional)
2 wires
Green - Input: Wake/Signal 6*
Black - Battery Negative
1x5 Microfit
RGY BUTTON
065-1010
(Optional)
20 ft./6.1m RGY extn.
harness: 060-1197
5 wires
 WARNING: Automatic drive formatting
Storage media might not be recognized on recorders running
different firmware. By design, unrecognized media automatically
formats when inserted into a recorder, so recording can
commence. Customers who swap cartridges between recorders
should ensure each recorder has the same firmware version.
4. An optional Video Monitor can be used from the video output
located on the front panel.
5. Use Safe Fleet-approved cards only.
6. Wake/Signal 6 input, active high (5-32V edge-triggered).
ports.
Purple - Signal 7
Blue - Signal 8
GPS RF
*
Antenna 1
ANT-G6-SM
Yellow - Vehicle Ign +12V
Black - Battery Negative
Red - Vehicle +12V
Power harness/fuse pkg.:
PH1X3UM20
6
SIGNALS
S01 - Black
S02 - Green
S03 - Red
S04 - Brown
S05 - White
Part #: 700-1299 R2