Viking VIDAR II User Manual page 5

EN
VIKING VIDAR II - User manual
Thank you for choosing a VIKING product.
Please refer to the technical specifica�ons of each model in the user manual
or on the website www.best-power.cz
Method of use:
1. Please check that the device is fully charged before each use of the power
bank. The capacity and charging status are indicated by the LEDs near the
ON/OFF bu�on.
2. The power bank has an auto-start func�on when plugged in, or you can
manually turn it on using the ON/OFF bu�on. The power bank will automa�cally
turn off when idle if no charged device is connected. The power bank can also
be switched off manually using the ON/OFF bu�on or by disconnec�ng a
charged device.
3. The power bank can be fully recharged in about 3-4 hours. The charging �me
is only informa�ve and may vary depending on the power of the charging
source.
4. Specifica�ons, appearance and descrip�on are subject to change due to
product improvements and updates.
5. Always use a suitable charging cable.
6. Slight hea�ng of the product is normal with prolonged use.
7. Keep away from heat and dry.
Charging other devices - USB-C and USB-A:
- Connect the device to be charged with a cable with a suitable connector to the
output port on the powerbank (1 x USB-A, 2 x USB-C).
Mul�ple devices can be charged using all ports simultaneously, but in this case
fast charging is not supported for any of the outputs.
- Charging starts automa�cally.
- Using a suitable cable with Apple Lightning connector, you can also charge Apple products.
- The power bank supports fast charging
- If the device does not start charging, check the cables for proper connec�on. Try disconnec�ng and reconnec�ng the charging cable, then manually switching on the power
bank.
- When using the DC jack output and USB-C input/output, the power bank does not support pass-through. These two ports cannot be used at the same �me.
Charging other devices - DC jack (laptops, notebooks, etc.):
- Before using the DC jack output, set the appropriate power supply voltage for your device:
- Turn on the power bank by briefly pressing the ON/OFF bu�on.
- long press and hold the Voltage bu�on (approx. 3s) un�l the first voltage indica�on LED flashes (see descrip�on)
- Switch between 12V,16.5V,20V and 24V by pressing the Voltage bu�on briefly.
- when you have selected the correct value, wait un�l the LED stops flashing. If the LED is steady (not flashing), the power bank is ready to power the device with this output
voltage.
- Connect the device to be charged with a cable with a suitable connector (choice of 8 reducers) to the output port of the powerbank (1 x DC jack).
- Charging starts automa�cally.
- If the device does not start charging, check that the cables are connected correctly. Try disconnec�ng and reconnec�ng the charging cable and then manually switching on
the powerbank.
- To turn off the DC output, long press the Voltage bu�on (approx. 3s) un�l the output voltage value goes off.
Charging other devices - 12V cigare�e port:
ATTENTION: The supply voltage for the 12V cigare�e port is 12V and can charge devices up to 180W
- Connect the device to be charged with a cable with a suitable connector to the output port in the powerbank (1 x 12V cigare�e port).
- Charging starts automa�cally.
- Charging is terminated by disconnec�ng the device from the powerbank
- If the device does not start charging, check that the cables are connected correctly. Try disconnec�ng and reconnec�ng the charging cable, then manually switching on the
power bank.
Charging the power bank from an external power source:
- Connect the included DC jack adapter, DC jack connec�on cable (solar charging or car charging) or USB-C charging cable to the power source. Always follow the technical
specifica�ons of the power bank when charging. Charging starts automa�cally (LEDs flash according to the charge status, see descrip�on). The power bank supports the
pass-through func�on (discharging and charging at the same �me). When using the DC jack output and USB-C input/output, the power bank does not support pass-through.
These two ports cannot be used simultaneously.
Wireless wireless charging:
Turn on the power bank manually (wireless is ready when the green LED is on) and place the device to be charged on the surface designated for wireless charging. The device
being charged must support wireless charging.
LED light
Switch on the power bank manually. Press the ON/OFF bu�on twice (un�l the LED light turns on) to turn on the emergency red light. Double press (2x/1s) the ON/OFF bu�on to
turn on the full LED light, each subsequent single press switches to the dim light and back to the full light. Another double press of the ON/OFF bu�on turns the LED light off.
Warnings and declara�ons:
1. Do not disassemble the device or its accessories.
2. Do not modify, disassemble, open, puncture, remove or otherwise tamper with the rechargeable ba�ery inside the device.
3. Protect from fire, prolonged direct sunlight, and other heat sources to prevent overhea�ng and damage to the device, including the ba�ery inside the device.
4. Protect from contact with water and wet objects, especially when using the equipment.
5. Protect from high voltage equipment.
6. Do not throw or shake the equipment.
7. Do not use chemical cleaners to clean the equipment.
8. This equipment is not intended for use by persons (including children) whose physical, sensory or mental disability or lack of experience or knowledge prevents them from
using the equipment safely.
9. When the device is not in use, secure the sockets with safety plugs (if the device has them), charge it at least once every 4 months. and maintain a capacity level of at least
50%.
10. Immediately stop using this equipment if it is damaged in any way.
11. For safety reasons, use only the original charger and cables designed for this device to charge it.
12. In case of igni�on, do not use a water ex�nguisher! If necessary, only a dry powder ex�nguisher is suitable for the product.
13. This product is intended for emergency power supply of electrical appliances only. It is not a full replacement for the permanent DC or AC power supply of household applian-
ces.
14. This device is designed to supply power to Class II (double insulated) appliances.
15. Altering, damaging or obscuring the logo and nameplate on the equipment is strictly prohibited.
16. When installing the device (if possible), use suitable tools to �ghten all screws.
17. It is strictly forbidden to operate under voltage during installa�on (if possible).
Protect from children!
Ignoring the following safety instruc�ons may result in fire, electric shock, or damage to the equipment
12
11
3
4
1
2
/ 1 5
1 2 V
T
O U
D C
U T
IN /O
B - C
U S
5
B
U S
B - C
9
U S
8
7
6
BONA SPES s.r.o.
Product descrip�on
1. ON/OFF bu�on
2. Ba�ery capacity status LEDs
3. Voltage bu�on
4. Output voltage LEDs
5. Wireless charging LED
6. USB-C output
7. USB-A output
8. USB-C input/output
9. DC jack input/output
10. DC 12V cigare�e port (output)
11. Wireless wireless charging
12. LED light
A
10
Package contents:
VIKING power bank
USB-A-USB-C charging cable
USB-C to USB-C charging cable
DC Jack charging cable (CPAP)
Set of DC jack reduc�ons (8 pcs)
AC power adapter
Protec�ve packaging