NVC 303 Quick Start Manual Table of Content Installation & Settings ....................... 2 1.1. System requirement: ..................2 1.2. Install IP camera ....................2 1.2.1. Install on ceiling................... 2 1.2.2. Install on the wall..................5 1.3. Connect IP camera cable..................7 1.4.
NVC 303 Quick Start Manual 1. Installation & Settings 1.1. System requirement: OS:Windows 2000 or Windows XP Communication:TCP/IP Interface:10/100M base LAN Browser:Internet Explore 1.2. Install IP camera We have two way to install this IP camera. One is install on ceiling. Another is install on the wall.
NVC 303 Quick Start Manual 1.4. Internet connection Reference for Intranet and Internet connection methods: Internet refers to Public IP Address, while Intranet refers to Private IP Address. Private IP Address ranges: 10.0.0.0 through 10.255.255.255 • 172.16.0.0 through 172.31.255.255 •...
Page 10
NVC 303 Quick Start Manual Method TWO:IP camera connects to Internet directly. If it is a fixed IP, you have to type the IP Address provided by your ISP. If it is a floating IP, you have to type the account and password provided by the ISP to dial-up.
NVC 303 Quick Start Manual 1.5. Start IP camera Please confirm your IP camera is power on and connect to Ethernet HUB. After 30 second, IP camers can be actived. Now we have two way to find this IP camera. One is set your PC IP address to 192.168.1.XXX, this IP camera default IP address is...
Page 26
NVC 303 Quick Start Manual IP camera IE interface as show in picture: Function introduce as bellow: (1) Play、Stop、REC (2) Snapshot (3) View Size (4) PTZ Control : you can control the way、zoom and focal length (5) PTZ default setup (6) Video Control : Brightness、Contrast、Saturation...
NVC 303 Quick Start Manual 3. IE function interpretation 3.1. Basic Configuration 3.1.1. Status Click Setup button into Basic configuration function, Status shows System Information、Firmware current version、MAC Address、Camera information、Total live view users、Wireless status、OCX information : System Information: <1> Firmware Current Version:It shows firmware version you are using and the version date.
Page 28
NVC 303 Quick Start Manual <3> LAN Netmask Address:It shows the module’s Netmask address. <4> LAN Gateway Address:It shows the module’s Gateway address. <5> DHCP State:It shows the module’s enable or disable. Camera Information: <1> Camera Type:It show the camera’s specification. The default value is NTSC.
NVC 303 Quick Start Manual 3.1.2. Video & Audio Settings Video Stream: <1> CBR:Control Enable / Disable video stream. 128kbps,256kbps, 384 kbps , 512 kbps , 1M kbps , 1.5M kbps , 2M kbps , 3M kbps. Default: Disable <2> Resolution:Change the resolution of IE, there are D1、Field、...
Page 30
NVC 303 Quick Start Manual snapshot. Default : c:\image。(It means save file at C:\, file name will be “image+ take snapshot time + jpg” ) <2> Time Label:Turn on/Turn off time label (Yes / No). Default: Off OSD: <1> OSD Text:Enters the text in the text box to be displayed on the video image.(only 32 bytes).
NVC 303 Quick Start Manual 3.1.3. Networking IP Address Configuration: There are 2 methods to set up IP Address. One is obtaining IP address settings automatically (DHCP), and the other is assigning IP address manually. If your network supports DHCP, click the button of View to obtain the IP address automatically from the DHCP server.
NVC 303 Quick Start Manual 3.1.4. Wireless Settings Basic Configuration: <1> Operation Mode:Two modes, Infra ( Infrastructure Mode) and Ad-Hoc Mode. If you are just operating with AP, please select Infra mode, if it is a point-to-point transmission, please select Ad-Hoc mode.
Page 33
NVC 303 Quick Start Manual <5> TX Rate:Sets up the transmission speed, Auto、1、2、5.5、11、 6、9、12、18、24、36、48、54Mbps. Default is auto. <6> SSID:The SSID you enter should be consistent with AP’s SSID. The default is ipcam_wlan. <7> Ad-Hoc Mode:Sets up the transmission mode of Ad- Hoc, 802.11b and 802.11g.
Page 34
NVC 303 Quick Start Manual <4> WEP Key ID 1~4:From the drop-down list, select the ID is HEX format or ASCII format. The number of character depends on the number of WEP key bit settings. For Hex format, the characters allowed for input are from 0 –...
NVC 303 Quick Start Manual 3.1.5. PPPoE Configuration: <1> Enable PPPoE:Enables or disables this function. <2> User Name:Enter the account provided by ISP. <3> Password:Enter the password provided by ISP. <4> MTU:Maximum Transmission Unit. <5> Email Notification when IP is changed:Enables or disables this function.
NVC 303 Quick Start Manual 3.1.6. DDNS Dynamic DNS: To use DDNS service, be sure to go to the web site of DynDNS (www.dyndns.org) and PeanutHull, and register for a dynamic domain name, which can be used to access it over Internet. Free of charge. Or you can’t use the service.
NVC 303 Quick Start Manual 3.1.7. DATE & TIME Current Server Time:Shows the current date and time displayed by Module. Time Zone:Selects your time zone from the drop-down list. Time Mode:The Module will obtain the time from an NTP server.
NVC 303 Quick Start Manual 3.2.2. ADMINISTRATOR User List:Adds/Removes user account. Add New User: User Name:Enter A-Z or a-z, only use English and number to make up user name, and user name has to less than 14 characters. Password:Key in password.
Page 41
NVC 303 Quick Start Manual User level only can view information, he can not change for any information. Save:Press “ save “ button, the user that succeeds to add will display in the table. Remove:Click Remove to cancel user name at user list.
NVC 303 Quick Start Manual 3.2.4. SMTP To set up mail server, please use the mail server provided by your ISP company or Yahoo’s free account. For example, if your board uses ISP internet service, and you send E-mail via So-net, you have to fill in ISP mail server in the mail server section.
NVC 303 Quick Start Manual 3.2.5. FTP FTP Settings:REC file can update to FPT. FTP Server:Enter FTP server. User Name:Please key in the account number that you apply for. Password:Please key in the password that you apply for. FTPCommandPort:Set up FTP Command port, Default: 21.
NVC 303 Quick Start Manual 3.2.7. ALARM EVENT Embedded Motion Detection Setting Set Motion Detect Region: Set up motion detect function, Click “ Begin “, choose range 0~15 and click “ Edit Region “, and then you can edit the region of video. If want to cancel the region, please click “...
Page 47
NVC 303 Quick Start Manual <1> Alarm Level:Have three kinds of type low alarm, high alarm and no alarm. When the GPIO normal of the input is a high level, then select " low level " ; When the GPIO normal of the input is a low level, then select "...
NVC 303 Quick Start Manual 3.2.8. Special Setting Video Advance Setting: Compression:Set video compression Compression Bit rate 170~850 kbps 120~500 kbps 110~360 kbps 110~330 kbps 110~270 kbps P/I Ratio(P frmae ; I frame):Can change the ratio of the P frame and I frame...
NVC 303 Quick Start Manual 3.3. REC View PLAYBACK: This page only provides the video which is recorded previously. Click “ browse ” button can select to want to broadcast file(*.av) path. Click "Play" button to start broadcasting then after selecting file, click "...
Need help?
Do you have a question about the NVC 303 and is the answer not in the manual?
Questions and answers