Advertisement

Quick Links

Introduction:
Due to high potential of spillage and runoff from rooftop ventilation and exhaust fans and the Fats, Oils and Grease
(F.O.G.) they produce, The Irvine Company, Retail Properties group has created the following criteria. This
criterion has been created to significantly reduce the exposure of F.O.G. on the Landlord's roofing systems and
exposure to runoff into the rooftop storm drain systems. F.O.G. is acidic in nature and causes rapid deterioration of
roofing materials. Additionally, runoff of F.O.G. into the storm drain systems puts both the Tenant and Landlord at
significant risk with Governmental agencies that monitor water quality issues.
Equipment:
Rooftop equipment designed by the Tenant shall conform to all regulatory and statutory requirements set forth by
all municipal reviewing agencies. In addition, the following requirements shall also be adhered to in the design of
the Tenant's rooftop exhaust and ventilation systems:
1. Rooftop exhaust systems shall be designed to accommodate all code requirements, but shall not be over
designed as to discharge extraordinary amounts of F.O.G. onto the surrounding roof system. Exhaust
velocities shall be maintained to manufacturer specifications to adequately capture all discharge materials.
2. All rooftop equipment shall provide rainproof capture and collection systems for any and all F.O.G.
discharge.
3. Rooftop exhaust and ventilation equipment shall be installed in compliance with Landlord's rooftop
equipment installation details set forth elsewhere in this criterion.
Although, the design and engineering of rooftop exhaust and ventilation equipment is regulated through municipal
code, The Irvine Company, Retail Properties has found the following companies to provide superior grease
containment and capture to other manufacturers and require that Tenants utilize one of these manufacturers.
Supreme Fan Products
Central Blower Company
Alternative manufacturers may be utilized only if the equipment specifications are equal to or exceed those provided
by the aforementioned manufacturers and approved in writing by Landlord. The Landlord does not warrant, nor
assumes any liability for the products or performance of the aforementioned companies.
Rooftop Grease Design and Installation Criteria
435 East Lincoln Street
Banning, California 92220
Phone: (909) 849-6778
Fax:
(909) 849-7091
th
Ave.
211 S. 7
City of Industry, Calif. 91746
Phone: (626) 330-3182
Fax:
(626) 330-9406
www.centralblower.com

Advertisement

Table of Contents
loading

Summary of Contents for CENTRAL RE Series

  • Page 1 Supreme Fan Products 435 East Lincoln Street Banning, California 92220 Phone: (909) 849-6778 Fax: (909) 849-7091 Ave. Central Blower Company 211 S. 7 City of Industry, Calif. 91746 Phone: (626) 330-3182 Fax: (626) 330-9406 www.centralblower.com Alternative manufacturers may be utilized only if the equipment specifications are equal to or exceed those provided by the aforementioned manufacturers and approved in writing by Landlord.
  • Page 2 Maintenance: Tenants are required to maintain all grease producing rooftop equipment to eliminate the possibility of runoff of F.O.G. onto Landlord’s roof systems and into roof drains. Maintenance shall be performed by a Landlord approved company licensed to inspect and maintain exhaust systems and shall occur a minimum of 6 times annually or more frequently as required by governing agencies and shall consist of the entire system from the rooftop exhaust and ventilation units all shafts leading down to the source equipment and any and all filtration systems associated with this equipment.
  • Page 3 CENTRAL BLOWER COMPANY CENTRAL BLOWER COMPANY 211 S. 7th Ave. • City of Industry, CA 91746 (626) 330-3182 Fax (626) 330-9406 www.centralblower.com CATALOG • REF - 04 FEBRUARY, 2004...
  • Page 4 Centrifugal Blowers performed in accordance with are available as AMCA Publication 211 and comply U.L. Listed for top and bottom with the requirements of AMCA Grease Removal (UL762) Certified Ratings Program. Page 2 • Central Blower Restaurant Exhaust Fan Catalog...
  • Page 5 ▲ Sized to fit CFM ▲ Variable pitch motor pulley fitting for maintenance ▲ Ground and Polished requirements allows speed adjustment ▲ Mounted outside away in the field shafts with keys from heat & grease Central Blower Restaurant Exhaust Fan Catalog • Page 3...
  • Page 6 19 1/4 39 7/8 14 1/2 26 1/2 RE-22 23 13/16 23 1/2 58 1/2 39 7/8 17 13/16 26 1/2 RE-24 26 1/4 25 7/8 57 1/4 19 1/2 21 1/2 Page 4 • Central Blower Restaurant Exhaust Fan Catalog...
  • Page 7 29 3/4 17 1/2 1 1/2 RE-15 24 1/2 21 1/2 29 3/4 17 1/2 1 1/2 RE-18 39 7/8 36 7/8 1 1/2 RE-22 39 7/8 36 7/8 1 1/2 RE-24 Central Blower Restaurant Exhaust Fan Catalog • Page 5...
  • Page 8 Performance ratings include the effects of a discharge scoop in the airstream. Centrifugal Blowers performed in accordance with Consult Central Blower Co. for CFM and S.P. not listed above. are available as AMCA Publication 211 and comply U.L. Listed for...
  • Page 9 Performance ratings include the effects of a discharge scoop in the airstream. Centrifugal Blowers performed in accordance with Consult Central Blower Co. for CFM and S.P. not listed above. are available as AMCA Publication 211 and comply U.L. Listed for...
  • Page 10 Central Type Bl Centrifugal Blowers performed in accordance with are available as AMCA Publication 211 and comply U.L. Listed for with the requirements of AMCA Grease Removal (UL762) Certified Ratings Program. Page 8 • Central Blower Restaurant Exhaust Fan Catalog...
  • Page 11 ▲ Sized to fit CFM requirements ▲ Cast iron for long life ▲ Rubber isolated for quiet ▲ Mounted outside, away from ▲ Variable pitch motor pulley operation heat and grease for speed adjustment Central Blower Restaurant Exhaust Fan Catalog • Page 9...
  • Page 12 55 1/2 1 11/16 36 BI 36 1/2 39 1/8 29 3/16 71 3/8 43 7/8 11 3/8 22 7/8 38 5/8 31 9/16 65 7/8 9/16 67 3/16 1 15/16 Page 10 • Central Blower Restaurant Exhaust Fan Catalog...
  • Page 13 Power rating (BHP) does not include drive losses. Add 10% for drive loss. Centrifugal Blowers Performance ratings do not include the effects of appurtenances in the airstream. are available as U.L. Listed for Grease Removal (UL762) Central Blower Restaurant Exhaust Fan Catalog • Page 11...
  • Page 14 Power rating (BHP) does not include drive losses. Add 10% for drive loss. Central Type Bl Centrifugal Blowers Performance ratings do not include the effects of appurtenances in the airstream. are available as U.L. Listed for Grease Removal (UL762) Page 12 • Central Blower Restaurant Exhaust Fan Catalog...
  • Page 15 Power rating (BHP) does not include drive losses. Add 10% for drive loss. Central Type Bl Centrifugal Blowers Performance ratings do not include the effects of appurtenances in the airstream. are available as U.L. Listed for Grease Removal (UL762) Central Blower Restaurant Exhaust Fan Catalog • Page 13...
  • Page 16 Power rating (BHP) does not include drive losses. Add 10% for drive loss. Central Type Bl Performance ratings do not include the effects of appurtenances in the airstream. Centrifugal Blowers are available as U.L. Listed for Grease Removal (UL762) Page 14 • Central Blower Restaurant Exhaust Fan Catalog...
  • Page 17 Power rating (BHP) does not include drive losses. Add 10% for drive loss Central Type Bl Performance ratings do not include the effects of appurtenances in the airstream. Centrifugal Blowers are available as U.L. Listed for REV 11/03 Grease Removal (UL762) Central Blower Restaurant Exhaust Fan Catalog • Page 15...
  • Page 18 Backward Inclined Wheels WARRANTY Central Blower Co. (the Company) warrants that each blower manufactured by the Company shall be free from defects in material and workmanship under normal use and service for a period of eighteen (18) months from the date of shipment or twelve (12) months from date of original installation,“whichev- er occurs first.”...
  • Page 19 EXHAUST BLOWER Installation, Maintenance and Service Manual Experience the Supreme Difference...
  • Page 20: Table Of Contents

    Table of Contents Installation Procedure ............3 Basic Component Identification Drawing .
  • Page 21: Installation Procedure

    Kitchen Hood Exhauster – Installation Procedure Duct Construction 1. Ducts should be sized for a minimum air velocity of 1500 FPM and a maximum of 2200 FPM (consult local codes). 2. Ducts shall be constructed of material not less than 16 gauge steel. 3.
  • Page 22 Kitchen Hood Exhauster – Installation Procedure Step-3 Installation of Top Blower Assembly Once the duct and transition are in place, the blower assembly can be set. Lifting lugs are factory provided for rig- ging. Set blower assembly on fan base so hinges match hinge holes in fan base. Tighten hinge bolts and install elec- trical.
  • Page 23: Basic Component Identification Drawing

    Basic Component Identification Motor Cover Motor Cover Support Arm Support Arm Retainer Clip Security Pin – Wheel Access Hole in Motor Frame For Support Arm Motor Frame Assembly Motor & Drive Motor Frame Assembly Cover Assembly Top Access Door Blower Wheel Discharge Scoop Wheel Access Cam Latch...
  • Page 24: Exhaust Fan Maintenance

    Supreme Exhaust Fan Maintenance The exhaust fan should be inspected and serviced at least every two months as follows: CAUTION: MAKE SURE THE POWER TO THE EXHAUST FAN IS TURNED “OFF” AT THE DISCONNECT SWITCH BEFORE WORKING ON THE EXHAUST FAN. WHEN ELECTRICAL CIRCUIT TESTING IS REQUIRED, IT SHOULD BE PERFORMED ONLY BY QUALIFIED SERVICE PERSONNEL.
  • Page 25: Motor Frame And Blower Wheel Assembly Drawing

    Motor Frame and Blower Wheel Assembly Motor Cover Assembly (Shown in Motor Phantom for Frame Clarity) Assembly Drive Belt (Motor) Pulley Allen Blower Screw Shaft Motor Split Taper Bushing Motor Driven (Blower) Mounting Pulley Plate Cap Screws Motor Cover Bearing Collar Wing Nut Allen Screw Grease Fitting...
  • Page 26: Troubleshooting Guide

    Troubleshooting Guide WARNING! INSPECTION, TESTING, SERVICING AND REPAIR OF THE EXHAUST BLOWER SHOULD BE PER- FORMED ONLY BY QUALIFIED SERVICE PERSONNEL. THE UNIT SHOULD BE TURNED OFF AT THE DISCON- NECT SWITCH WHEN SERVICING TO AVOID THE DANGER OF SOMEONE INADVERTENTLY TURNING THE UNIT ON WHILE IT IS BEING SERVICED.
  • Page 27 Troubleshooting Guide (cont.) PROBLEM PROBLEM CAUSE CORRECTIVE ACTION Grease leakage at fan a. Grease reservoir filled to a. Empty grease reservoir overflow b. Damaged lid to base gasket b. Replace gasket c. Damaged wheel access gasket c. Replace gasket d. Damaged grease reservoir d.
  • Page 28: Pulley Alignment

    Supreme Exhaust Fan Service DRIVE MOTOR AND DRIVEN BLOWER WHEEL PULLEY VARIATIONS: Drive Pulley This pulley is a variable pitch pulley. The pitch diameter of the pulley is adjustable to allow speeding up or slowing down of the blower wheel a small amount within the adjustment range of the pulley. For small single groove pulleys, an allen head set screw is provided in the shoulder on the bottom side of the pulley, to tighten the pulley to a flat spot on the shaft of the motor.
  • Page 29: How To" Replace Motor

    Supreme Exhaust Fan Service (cont.) To Replace Motor CAUTION! MAKE SURE POWER IS TURNED OFF AT THE DISCONNECT SWITCH PRIOR TO CHANGING MOTOR. Open the motor cover and install the cover support arm. Loosen the belt tension lock nuts and remove the belt. Remove the motor J-box cover.
  • Page 30: How To" Replace Fan Wheel Bearings

    Supreme Exhaust Fan Service (cont.) To Replace Fan Wheel Bearings CAUTION! MAKE SURE THE FAN IS TURNED “OFF” AT THE DISCONNECT SWITCH. Loosen the wing nuts, open the motor cover and install the cover support arm. Remove the “V” belt (see “How To Replace Belt”).
  • Page 31 Installation Wiring Diagram Note: Alternate For 208-230/460V. 208 – 230/460V. 3O Single Phase Motors, Control Source Delete Line 1.3 and 120V., 1 Phase Associated Components GND. Delete if Circuit Breaker Alternate Field Furnished Control Source & Installed Used Conduit & Conductors Field Furnished &...
  • Page 32: Wiring Diagrams

    Optional Disconnect Switch, Conduit & Wiring Installation (3 Phase Shown, 1 Phase Similar) Motor Leads – See Motor NOTE: Wiring Diagram 1- All component parts shall be ETL or UL listed or classified. 2- Conduit & fitting sizes shall be per the NEC (Nat’l, Elec. Code) Grounding Screw 3- The conductors shall be sized for 125% of the full load amps the on Motor Case...
  • Page 33: Warranty

    Warranty What Products Are Covered Supreme Fan products (each, a "Supreme Fan Product") One Year Limited Warranty For Supreme Fan Products Supreme Fan warrants to the original commercial purchaser that the Supreme Fan Products will be free from defects in material and workmanship for a period of one (1) year from the date of shipment. Exclusive Remedy Supreme Fan will, at its option, repair or replace (without removal or installation) the affected components of any defective Supreme Fan Product;...
  • Page 34 Experience the Supreme Difference 843 Indianapolis Avenue Lebanon, IN 46052 Phone: 765-483-5819 www.supremefan.com...
  • Page 35 Supreme Fan Supre Bulletin SF-GB06 Supreme Fan January 2006 Supreme Fan Supre Supreme Fan Supreme Fan Supre Supreme Fan Supreme Fan Supre Supreme Fan Supreme Fan Supre Supreme Fan Supreme Fan Supre Supreme Fan Supreme Fan GBD-C C -H H Supre Heavy-Duty Curb Mounted Supreme Fan...
  • Page 36 Table of Contents Introduction..............3 Features .
  • Page 37: Introduction

    Introduction Whether installing a new kitchen ventilation system or Supreme Fan offers a 36" discharge extension, if renovating an existing one, quality conscious restaurant needed, to extend the discharge above the roof line. owners and designers have insisted on GBD from Grease Reservoir Supreme Fan for over 25 years.
  • Page 38: Optional Equipment

    Optional Equipment Extended Discharge Scoop The optional extended discharge scoop is available if a greater distance is required between the exhaust and supply inlets in order to meet code requirements or job site conditions. The single outlet discharge on the GBD makes this separation easier.
  • Page 39: Sample Specifications

    Sample Specifications GBD exhaust blowers shall be curb-mounted with fan housing entirely constructed of heavy gauge steel, fully welded. Blower shall have a single, integral, continuously welded upblast discharge scoop constructed of similar materials with a fully welded drain for liquid to travel to a fully welded grease reservoir.
  • Page 40 GBD DIMENSIONAL DATA Discharge Scoop Grease Drain Drain Reservoir *17 1/2" Vented Base 4" 1 1/2" *18 1/2" on GBD - 125 & GBD - 150 Hinged Access to Grease Duct 12" - Size 125 / 150 Wood Drain 8" - Size 185 - 300 Nailer +Nominal max.
  • Page 41: Grease Duct Installation

    Grease Duct Installation Grease Duct Installation Procedure 1. Loosen hinge bolts securing blower to base. Lift blower off base. Set Exhaust base on roof curb. Blower Side View 2. Drop grease duct through Drain opening in base. Flanges on duct will set on lip of base to 1/2"...
  • Page 42 GBD Performance Data GBD-125 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 0 GBD-150 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 0 GBD-182 "...
  • Page 43 GBD Performance Data (cont.) GBD-245 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 0 " 0 GBD-270 " 0 " 0 " 0 " 0 " 0 " 0 " 0 "...
  • Page 44 GBD Lubrication & Maintenance Prelubricated Bearings Maintenance Procedures All bearing units are prelubricated with grease chosen The exhaust blower should be inspected every three for its chemical and mechanical stability. months as follows: Units furnished with a grease fitting should be 1.
  • Page 45: Warranty

    Warranty What Products Are Covered Supreme Fans (each, a “Supreme Fan Product”) One Year Limited Warranty For Supreme Fan Products Supreme Fan warrants to the original commercial purchaser that the Supreme Fan Products will be free from defects in material and workmanship for a period of one (1) year from the date of shipment. Exclusive Remedy Supreme Fan will, at its option, repair or replace (without removal or installation) the affected components of any defective Supreme Fan Product;...
  • Page 46 upreme Fan Supre Suprem upreme Fan upreme Fan Supre Suprem upreme Fan upreme Fan Supre Suprem upreme Fan upreme Fan Supre Suprem upreme Fan upreme Fan Supre Suprem upreme Fan upreme Fan Supre Suprem upreme Fan upreme Fan Experience the Supreme Difference Supre 843 Indianapolis Avenue Lebanon, IN 46052...

This manual is also suitable for:

Re-12Re-15Re-18Re-22Re-24

Table of Contents