Page 2
ATTENTIONS TO BE PAID FOR SAFETY ATTENTIONS TO BE PAID FOR SAFETY ATTENTIONS TO BE PAID FOR SAFETY ATTENTIONS TO BE PAID FOR SAFETY DON`T FAIL TO FULFILL DON`T FAIL TO FULFILL DON`T FAIL TO FULFILL DON`T FAIL TO FULFILL You should fulfill following exp You should fulfill following exp You should fulfill following exp...
Page 3
Don ′ ′ ′ ′ t disassemble and t disassemble and t disassemble and t disassemble and Connect with the power Connect with the power Connect with the power Connect with the power Disconnect the power Disconnect the power Disconnect the power Disconnect the power repair absolutely except repair absolutely except...
Page 4
Don′ ′ ′ ′ t install the machine to the site high humidity(For fear of causing electric leaks) t install the machine to the site high humidity(For fear of causing electric leaks) t install the machine to the site high humidity(For fear of causing electric leaks) t install the machine to the site high humidity(For fear of causing electric leaks) Don′...
Page 5
3 3 3 3 . . . . SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS HP-1000LW MODEL POWER SUPPLY 3P-380V 400W DRIVING MOTOR RATED OUTPUT BWP MOTOR 40W×2 ROTARY STRIP OFF MOTOR HEATERPWER 21.6Kw BELT SPEED 12.7m/min(Max) BELT WIDTH 1000mm PRESSUR 5.0kg/cm (Max) 200 ℃(Max)...
Page 6
4 4 4 4 、 、 、 、 DIMENSIONS DIMENSIONS: : : : DIMENSIONS DIMENSIONS From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
5. OUTSIDE MAIN PARTS 5. OUTSIDE MAIN PARTS 5. OUTSIDE MAIN PARTS 5. OUTSIDE MAIN PARTS 1. WORK TABLE 14. CIRCUIT BREAKER 2. RIGHT COVER 15. ADJUSTER 3. EMERGENCY SWITCH 4. FRONT COVER 5. EMERGENCY SWITCH 6. UPPER COVER 7. REAR COVER 8.
Page 8
6. 6. 6. 6. INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION ※ T T T T his his machine machine machine machine have have have have the w the w the weight of about 1 the w eight of about 1 eight of about 1 eight of about 15 5 5 5 00kg 00kg...
○ PRESSUER DIAGRAM 1. 1. 1. 1. Turn on the circuit breaker switch on the Turn on the circuit breaker switch on the Turn on the circuit breaker switch on the Turn on the circuit breaker switch on the left left left under left...
Page 11
4 4 4 4 ..Turn the dial of the fusing timer, and set to the proper fusing time. Turn the dial of the fusing timer, and set to the proper fusing time. Turn the dial of the fusing timer, and set to the proper fusing time. Turn the dial of the fusing timer, and set to the proper fusing time.
Page 12
HASHIMA NEW CLEAN. with HASHIMA NEW CLEAN. with HASHIMA NEW CLEAN.
Page 14
10 10 10 10. . . . BELT CLEANER POSITION BELT CLEANER POSITION BELT CLEANER POSITION BELT CLEANER POSITION ※ ※ ※ ※ Exchange the belt cleaner for a new one when the heat on the machine unit is cooled enough, Exchange the belt cleaner for a new one when the heat on the machine unit is cooled enough, Exchange the belt cleaner for a new one when the heat on the machine unit is cooled enough, Exchange the belt cleaner for a new one when the heat on the machine unit is cooled enough,...
Upper cleaner Cleaner 3 Cleaner 4 How to belt exchange How to belt exchange How to belt exchange How to belt exchange 1. Make space for maintenance around the machine. 2. Take out upper cover, front cover, rear cover, left side cover, right side cover. From the library of Superior Sewing Machine &...
Page 16
3. After take out upper cover, remove insulation cover. Insulation cover 4. Take out fixing plate, upper cover fixing plate, frame fixing holder. 5. Loosen tension roller set screw. 6. After loosen belt tension, take out tension roller. 7. Set to pressure to 0. From the library of Superior Sewing Machine &...
Page 17
8. Take out upper frame and lower frame (8 position), take out belt warping prevention roller. 10. Take out frame joint plate(9 position) 11. Take out connecting screw of base frame and lower frame.(8position) air cylinder connecting rod 12. Take out right air cylinder connecting rod. ﹙ 2position ﹚ From the library of Superior Sewing Machine &...
Page 18
belt exchange pipe belt exchange pipe stand 13. Long pipe stand is for upper belt exchange, short pipe stand is for lower belt From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 19
exchange 14after set belt exchange pipe and pipe stand, take out Teflon belt from space between upper frame and lower frame. NOTE When the belt is pulled out, be careful not to let the belt touch the belt warping prevention limit switch. There are setting marks on the frames.
PARTS LIST WHOLE BODY MAIN FRAME PART DRIVING AND PRESSURE PART HEATENIN PART BELT WARPING PREVENTION PART ANTI PUCKERING ROLLER PART CLEANER PART TABLE PART REAR CONVEYOR PART COVER PART ELECTRIC PART From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 21
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 22
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 23
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 24
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 25
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 26
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 27
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 28
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 29
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 30
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 31
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 32
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Page 33
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com...
Need help?
Do you have a question about the HP-1000LW and is the answer not in the manual?
Questions and answers