Advertisement
Locking mechanism allows rollers to be fixed at eight pre-set positions. Mounted on two locking casters and two non-locking for
improved stability and easy manoeuvrability. Ideal for use on agricultural and commercial wheels and tyres.
3.
SPECIFICATION
Model No: .....................................................W1200T.V3
Maximum Lifting Capacity: .................................. 1500kg
Minimum Wheel Ø: ......................................... Ø1000mm
Maximum Wheel Ø: ........................................ Ø2000mm
Roller Length: ...................................................... 490mm
Minimum Lifting Height: ........................................ 0.1mm
Maximum Lifting Height: ...................................... 750mm
Overall Size (W x D x H): ........... 1300 x 1015 x 1500mm
4.
ASSEMBLY LIST
Part
Description
1
Clamp support arm
2
Sliding tube
3
Adjustment clamp
4
Wheel support
5
Support frame (left)
6
Bolt M16x130mm
7
Braked castor
8
Flat washer 16mm
9
Spring washer 16mm
10
Nut M16
11
R clip
12
Frame
13
Pin
14
Bolt M16x110mm
15
Support frame (right)
16
Bolt M16x100mm
17
Mounting bar
18
Castor
19
Handle
20
Handle
21
Roller table
22
Handwheel + washer
23
Spring
5.
ASSEMBLY
5.1.
Refer to fig.1.
5.2.
Ensure that at least two people assemble the trolley.
5.3.
Fit support frame (left) (5) to frame (12). Use bolt M16 x 110mm (14), flat washer 16mm (8), spring washer 16mm (9) and nut M16
(10).
5.4.
Fit support tube (right) (15) to frame (12). Use bolt M16 x 110mm (14), flat washer 16mm (8), spring washer 16mm (9) and nut M16
(10).
Note: Support frames are not handed. Ensure warning symbols are upwards and visible on trolley.
5.5.
Fit braked castors (7) to frame (12). Use bolt M16 x 130mm (6), flat washer 16mm (8), spring washer 16mm (9) and nut M16 (10).
5.6.
Fit unbraked castors (18) to end of support frame (left) (5) and support frame (right) (15). Use bolt M16 x 100mm (16), flat washer
16mm (8), spring washer 16mm (9) and nut M16 (10).
5.7.
Fit roller tables (21). Get one person to hold table whilst other inserts mounting bar (17) with R clip hole end going in first. Secure
with R clips (11).
5.8.
Fit roller table tension springs (23). Insert top end of spring into hole on end of roller tables (21) and the other end of the spring into
nut welded onto the inner edges of support frame (right) (15) and support frame (left) (5).
5.9.
Fit wheel support (4) to frame (12) with handle to rear. Use pin (13) and R clip (11). Ensure R clips are on outside of frame as
shown in fig.1.
5.10.
Insert clamp support arm (1) into sliding tube (2), (remove hand wheel and washer (22) first), tighten clamp (3). Insert into wheel
support (4), tighten clamp on wheel support (4).
5.11.
Insert handles (19 and 20) into sockets shown in fig.1.
5.12.
PURGE HYDRAULIC SYSTEM
5.12.1. Open the release valve by pressing down the lowering pedal (Fig.2 ).
5.12.2. Pump the handle a minimum of twenty full strokes.
5.12.3. Close the release valve by lifting the pedal back to its highest position.
© Jack Sealey Limited
Quantity
1
1
2
1
1
2
2
6
6
6
4
1
2
2
1
2
2
2
1
1
2
1
2
Original Language Version
Fig.1
W1200T.V3
Issue 2 (H,5,F)
16/08/23
Advertisement
