Advertisement
4.
OPERATION
4.1
Clamping Drum.
4.1.1
The opening section of the hoop (Fig.1.15) is sprung loaded to remain open when not
clamped to a drum.
4.1.2
Position the Drum Handler so that the supporting hoop (Fig.1. 3) encompasses the
drum to be lifted.
4.1.3
Pull the location levers (Fig.1.10) to release the handle (Fig.1.4) to locate the
supporting hoop in the middle of the drum.
4.1.4
Release the location levers to lock the handle in this position.
4.1.5
Turn the fastening lever (Fig.1.6) so the teeth are pointing upwards, take the slack up
on the chain and place it in the groove (Fig.3) on the fastening lever ensuring that it is
fully located as in Fig.3.1.
4.1.6
Pull the fastening lever sharply clockwise until the chain is tight and the ratchet pawl
has locked the ratchet as in Fig.4.
4.1.7
Check that the drum is now securely held in place. If the chain is not tight repeat
procedure 4.1.5 to 4.1.6 but take more slack out of the chain. The drum is now ready to
be lifted.
4.2
Lifting Drum.
4.2.1
Pull the handle (Fig.1.4) downwards, this will lift the drum.
4.2.2
When the drum is at the required height, slowly release the handle and the location
levers will automatically lock the handle in place.
4.3
Transportation.
4.3.1
Push or pull the drum handler using the handle to the required destination.
Apply pressure left or right to steer the handler.
CAUTION! Ensure that there are no obstructions in your path, make sure the floor
surface is suitable to take the weight of the fully laden drum handler.
4.4
Lower & Release Drum.
4.4.1
To lower the drum, apply downward pressure to the handle (Fig.1.4).
4.4.2
Pull the two location levers (Fig.1.10) at the same time.
4.4.3
This will release the handle and drum which may now be lowered to the ground, when
the drum reaches a firm surface, release the location levers.
4.4.4
Turn the fastening lever clockwise slightly to disengage the ratchet pawl.
4.4.5
Release the fastening lever and remove the chain and hang it on the hook (Fig.1.17).
4.4.6
Pull the drum handler away from the drum.
4.5
Rotate the Drum.
4.5.1
The drum handler can rotate the drum from vertical to horizontal position.
4.5.2
To turn the drum from vertical to horizontal disengage pins (Fig.1.5) and turn through 90° to lock them
in the disengaged position and then turn the drum through 90° to the horizontal position.
4.5.3
Rotate the pins again until they engage with the supporting hoop to secure the drum in the horizontal position.
Note!
Before rotating drum make sure drum has been lifted sufficiently high enough allowing it to turn without interference from the ground.
4.6
Adjustment.
4.6.1
If the supporting hoop is too high to hold the middle of the drum while the handle is at its highest point or the drum cannot be lifted to
the required height when the handle has reached its lowest point it will be necessary to adjust the height of the supporting hoop.
4.6.2
Choose another hole (Fig.1.13/16) on the lifting arm (Fig.1.11) and or the hanger plates (Fig.1.12) remove the hanger plate bolts
from the original position an relocate them in the new position ensuring that the same hole is chosen for each side.
5.
MAINTENANCE
5.1
Regularly check the drum handler chassis and wheels for rigidity. Ensure that the rear castor is firmly secured to the chassis.
5.2
Regularly check the pawl and ratchet for wear. Replace when necessary.
5.3
Regularly check the drum handlers connecting components such as retaining pins, nuts and washers for lubrication and/or wear.
5.4
Keep handle free from grease and oil to prevent accidents.
6.
DECLARATION OF CONFORMITY
Declaration of Conformity
MOBILE DRUM HANDLER 250ltr
Model DH02
98/37/EC Machinery Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
We, the sole importer into the UK, declare that the product listed below is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national authority, upon
request to Jack Sealey Ltd.
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
Fig 3
21 September 2005
01284 757500
01284 703534
Locate chain
in fastening lever.
Fig 3.1
Fig 4
Chain pulled tight
and secured by
ratchet pawl
For Jack Sealey Ltd. Sole importer into the
UK of Sealey Power Products.
www.sealey.co.uk
Web
sales@sealey.co.uk
email
Advertisement
