Remote Sensor; Peak Level Meter - Teac V-5010 Owner's Manual

Precautions
CE el
Environment
Avoid using the deck in the following
conditions:
eAt high temperatures (near a heater,
exposed to direct sunlight, etc.).
© At extremely low temperatures.
«Where there is excessive humidity.
e In a dusty atmosphere.
Where power line voltage fluctuations are
severe (the use of a voltage regulator may
be advisable),
Cassette Tape (Fig. 3)
Tape Selection:
For the automatic tape select function to
work properly, metal and chrome (cobalt)
'tapes must have tape identification holes.
Tape Handling:
Do not store tapes in the following places:
On top of heaters, exposed to direct sun-
light or in any other places with high
temperatures,
Near speakers, on TV sets or amplifiers,
or where they would be exposed to strong
magnetic fields,
Where humidity is high and in dirty,
dusty places.
Avoid dropping or subjecting cassettes to
excessive shocks.
Voltage Conversion (For general export
models) (Fig. 6)
If it is necessary to change the voltage
selector of the deck to be suitable for your
area, use the following procedure:
1. DISCONNECT THE POWER LINE
CORD.
2. Using a screwdriver, turn the selector
until the required voltage marking
appears.
IMPORTANT (for U.K. Customers)
'The wires in this mains lead are coloured
ein accordance with the: following code:
BLUE: NEUTRAL
eat as follows: - = S
'The wire which is coloured BLUE must
he connected to the terminal which is
marked with the letter N or coloured
BLACK. The wire which is coloured
BROWN must be connected to the
aor which is
In the U. K, thi ; unit is sold without Le
AC plug,
THE APPLIANCE CONFORMS WITH
EEC DIRECTIVE 87/308/EEC RE-
GARDING INTERFERENCE SUuP-
PRESSION
* Dolby noise reduction and HX Pro
headroom extension manufactured under
license from Dolby Laboratories Licensing
Corporation. HX Pro originated by Bang
and Olufsen.
"DOLBY", the double-D symbol OO and
"HX PRO" are trademarks of Dolby
Laboratories Licensing Corporation.
Features and Controls (Fig. 1)
Front Panel
@ POWER Switch
Press to switch the deck on, The display
window will be illuminated, Press again to
turn the deck off.
Note: When switching the power on again
after switching it off, be sure to wait for
more than 3 seconds.
@ REMOTE SENSOR (Remote Con-
trol Infrared Signal Receptor)
This receives signals from the provided RC-
394 (V-7010)/RC-393 (V-5010) infrared
remote control unit.
© Linear Counter
Indicates recording and playback time in
minute and second.
Q Mode Indicator
CD SYNC: Lights when CD synchro
start is activated,
REC: Lights in the recording mode
and flickers during record-
muting.
PLAY: Lights during playback and
recording.
PAUSE: Lights when the tape is
stopped temporarily.
@ CLEAR Button
Pressing the CLEAR button resets the
linear counter to zero (0000). Press this
button before starting recording or play-
back.
@ TAPE LENGTH Button
Set this to minimize the error in the counter
reading. (See page 7.)
@ RTZ Button
If this button is pressed, the tape is fast-
forwarded or rewound until a counter
reading of OOMOOS is reached, then the
deck stops. (See page 9.)
© Cassette Holder
Load the cassette here.
Connections (Fig. 2)
eTurn off the power of all equipment
before making connections.
Read the instructions of each component
you intend to use with the deck,
© AUTO MONITOR Button
To change the monitor mode between
source and tape, press this button. The
monitor mode is automatically selected in
accordance with the tape operation,
@ MPX FILTER Button
Press this button when making a recording
of an FM broadcast using Dolby NR, the
indicator lights. This eliminates the pilot
tone (19 kHz) and subcarrier tone (38 kHz)
of the FM broadcast which could affect
operation of the Dolby noise reduction
system. To release this function, press the
MPX FILTER button again,
@ DOLBY NR Selector
OFF: Set to this position when you do not
want to use any noise reduction
system.
DOB: Set to this position when making a
recording using the Dolby B noise
reduction system, or playing back
tapes recorded with Dolby B NR.
DUOC: Set to this position when making a
recording using the Dolby C noise
reduction system, or playing back
tapes recorded with Dolby C NR.
© Multi-Display Window
@ PEAK LEVEL METER
This meter shows the peak level of the
input or playback signal. The meter
has a peak hold feature; when the level
exceeds -7 dB, the peak level is held for
approx. 2 seconds.
Tape Type Indicator
Tape type indicator above the meter
indicates the type of tape being used,
The V-7010V-5010 has an auto tape
selector function, with which the NOR-
MAL, CrO, or METAL indicator lights
when a tape is loaded,
© CALIBRATION Indicator
Lights together with "LEVEL/BIAS"
in the calibration mode.