Table of Contents
Advertisement
Quick Links
PS1 Parking Slider Controller Outline
Contents
1.
Introduction .......................................................................................................................................... 2
a.
Content of Carousel USA Agreement ................................................................................................ 2
b.
Components ...................................................................................................................................... 2
2.
Control Panel ......................................................................................................................................... 2
a.
Enclosure Specifications .................................................................................................................... 2
b.
Connections ...................................................................................................................................... 2
c.
Features and Functions ..................................................................................................................... 3
d.
Front Panel Layout ............................................................................................................................ 3
e.
Electrical Schematic .......................................................................................................................... 3
f.
Drawing ............................................................................................................................................. 3
3.
Remote Controller (Transmitter) .......................................................................................................... 3
a.
Specifications .................................................................................................................................... 3
b.
Features and Functions ..................................................................................................................... 4
c.
Remote Control Button Layout ......................................................................................................... 4
4.
Standard Operating Procedure ............................................................................................................. 4
Carousel USA has proprietary rights on the information in this document. It is forbidden to copy, duplicate or disclose the
information herein, in whole or in part, or make use of the information, unless
PS1 Outline Rev 2
Revised 8/25/2022
Carousel USA
15206 Ceres Ave, Fontana, CA 92335
www.carousel-usa.com
Proprietary Information
8/25/2022
Page 1 of 4
Advertisement
Table of Contents
Troubleshooting
Summary of Contents for Carousel USA PS1
- Page 1 Proprietary Information Carousel USA has proprietary rights on the information in this document. It is forbidden to copy, duplicate or disclose the information herein, in whole or in part, or make use of the information, unless PS1 Outline Rev 2...
- Page 2 This document is intended to further detail the standard parking slider controller equipment described in the contractual agreement. It will cover functionality and provide step-by-step standard operating procedure. a. Content of Carousel USA Agreement CUSA PS1 Controls, with one (1) remote transmitter. b. Components Enclosure: JB121206HC Rittal H12"...
- Page 3 Enclosure Drawing See Attachment. 3. Remote Controller (Transmitter) a. Specifications o Frequency: 433MHz o Buttons: 4x1 step o Weight: 1 oz o Dimensions: 2.1” x 1.2” o Batteries: 1 x 12V 27A PS1 Outline Rev 2 8/25/2022 Page 3 of 4...
- Page 4 2. User will exit the vehicle and use the front panel Jog switch or the A/B buttons on the remote controller to move the slider in the desired direction. 3. Once the vehicle is in position, user will release the Jog switch, or press the A/B button again. PS1 Outline Rev 2 8/25/2022 Page 4 of 4...
- Page 6 7.26 11.81 6.08 10.24 CarouselUSA DESIGN BY: 8/25/2022 DRAWN BY: 8/25/2022 UNLESS OTHERWISE NOTED TITLE: DIMENSIONS ARE IN INCHES PS1 Slider Controller TOLERANCES General Dimensions .X = .125 .XX = .0625 .XXX = .010 CAROUSEL USA PROPRIETARY AND CONFIDENTIAL SIZE DWG.
- Page 7 Proprietary Information Carousel USA has proprietary rights on the information in this document. It is forbidden to copy, duplicate or disclose the information herein, in whole or in part, or make use of the information, unless permission has been previously obtained, in...
-
Page 8: Table Of Contents
-USA T AROUSEL ROUBLESHOOTING GUIDE 1. Introduction This manual provides a step-by-step guide to troubleshooting simple issues related to the Carousel-USA Parking Slider Controller. ONTENTS INTRODUCTION ............................2 HIS MANUAL PROVIDES A STEP STEP GUIDE TO TROUBLESHOOTING SIMPLE ISSUES RELATED TO THE . -
Page 9: Inspect Operational Area
-USA T AROUSEL ROUBLESHOOTING GUIDE 2. Inspect Operational Area Create a clear and free working area around the turntable, ensuring that there is no debris that could cause interference with the Slider while in motion and that no one would be endangered by sudden movement of the Slider at any time while troubleshooting. -
Page 10: Check Circuit Breaker
-USA T AROUSEL ROUBLESHOOTING GUIDE 4. Check Circuit Breaker A. Reset Circuit Breaker If the orange tabs on the circuit breaker have been flipped down, reset them by pushing them back up into the position displayed below. If they are forced down again, the fault condition is still present. -
Page 11: Vfd Faults Table
-USA T AROUSEL ROUBLESHOOTING GUIDE ***DISCLAIMER*** Before performing any work involving removing wire from terminals, ensure that power is turned off and proper precautions are taken to avoid electrical shock. If ever unsure about how to proceed, please email Carousel-USA at support@carousel-usa.com and provide a brief description of the issue as well as pictures inside the control box or call Carousel-USA at... - Page 12 -USA T AROUSEL ROUBLESHOOTING GUIDE Ensure that VFD Internal electronic parameter P103 is F007 Motor Overload overload trip set to 4.2 (See VFD Parameters Section) Check for blocked or dirty heatsink fins or Heatsink cooling fan on the Heatsink Over F008 Temperature exceeds VFD.
- Page 13 -USA T AROUSEL ROUBLESHOOTING GUIDE **IMPORTANT** **See VFD Parameters Section The drive was to set parameters Parameters commanded to write F048 before operating Defaulted factory default values turntable. Failure to to all parameters do so may result in damaged components** Drive rating of 150% Ensure total load on for 1 minute or 200%...
-
Page 14: Vfd Navigation
-USA T AROUSEL ROUBLESHOOTING GUIDE 7. VFD Navigation On power-up, the VFD display will show 0.0 Hz, indicating that the turntable is not moving. Hit enter, and the display will change to show one flashing letter and three solid numbers indicating that the up and down arrows will change the letter. -
Page 15: Parameters Set By Carousel-Usa
-USA T AROUSEL ROUBLESHOOTING GUIDE B. Parameters Set by Carousel-USA The following are parameters set by Carousel-USA, all others should be set at the factory default. Use these as a guide on which parameters need to be changed if the VFD gets set back to a factory default state (via parameter P041 or P112 being set to 1, or an F048 fault occuring): P103 (Motor Overload Current): 2.8A... - Page 16 -USA T AROUSEL ROUBLESHOOTING GUIDE d006 Drive Status First number represents deceleration (1 = true 0 = false), second number represents acceleration (1 = true 0 = false), third number represents forward or reverse (1 = forward 0 = reverse), and fourth number represents running or stopped (1 = running 0 = stopped)
-
Page 17: Controls Testing
-USA T AROUSEL ROUBLESHOOTING GUIDE 9. Controls Testing A. Test All Control Inputs Begin by attempting to move the turntable in both directions using the selector switch on the control panel door and on each remote you have. Take note which of these moves the table and in what direction. - Page 18 -USA T AROUSEL ROUBLESHOOTING GUIDE Also inspect the terminal blocks at the bottom of the control panel that hold wires of the same designation as those going into the faulty control inputs for loose connections and damaged wiring. Should any of the terminal blocks have loose connections, you will need a small flathead screwdriver to reinsert the wire as shown below.
- Page 19 Instructions to Pair Sonoff Smart Switch with Phone (via Wi-Fi) and RF Remote Pairing with Wi-Fi using eWeLink App: 1. Checklist before using the device: a. Your Smart phone or tablet is connected to a 2.4G Wi-Fi with internet. b. You have the correct password. c.
- Page 20 a. Press and hold any of the four switch buttons (labeled R1 – R4) for 7 seconds until the Wi-Fi LED fast blinks 3 times and repeats. b. Open the eWeLink app, tap the “+” icon at the bottom of the screen to search for a new device.
- Page 21 CONTROLS INSTALLATION MANUAL INSTALLATION GUIDE FOR MOUNTING AND WIRING OF PARKING SLIDER CONTROLS P a g e...
- Page 22 SONOFF 4CH PRO WIFI SWITCH MOUNTING HOLES 10A CIRCUIT BREAKER TERMINAL BLOCKS WITH PIGTAILS VARIABLE FREQUENCY DRIVE CORD GRIP P a g e...
- Page 23 MOUNTING INSTRUCTIONS 1. Mounting the control box should be done before wiring. 2. The image on page 2 of the document displays four mounting holes circled in red. Carefully mark these holes onto a wall. Refer to the PS-INSTALL drawing and Step 8 on the Installation Manual for control box mounting location.