Related Manuals for Crestron Electronics TST-1080
Summary of Contents for Crestron Electronics TST-1080
- Page 1 TST-1080 10.1 in. Wireless Touch Screen Installation Guide Crestron Electronics, Inc.
- Page 2 Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource. Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
-
Page 3: Table Of Contents
Contents TST-1080 Installation (with TST-1080-DSW) ..........4 In the Box (TST-1080-DSW) ................... 4 Install the Mounting Hardware ..................4 Install the TST-1080-DSW....................5 Dock the Touch Screen ....................9 Undock the Touch Screen ..................... 10 — Doc. Contents • Installation Guide... -
Page 4: Tst-1080 Installation (With Tst-1080-Dsw)
Use the following procedures to install the TST-1080 touch screen with the TST-1080-DSW. NOTE: The TST-1080-DSW wall dock is designed for flush-mount installation in a flat, vertical wall structure. Installation of the wall dock requires additional mounting hardware (not included): •... -
Page 5: Install The Tst-1080-Dsw
Install the Mounting Hardware (on page 4). For preconstruction mounting hardware, it is also assumed that drywall is in place and a cutout for the TST-1080-DSW has been made. To install the TST-1080-DSW wall dock: 1. Route the wiring for the TST-1080-DSW power connection through the rear of the mounting hardware. - Page 6 4. While holding the included bezel, connect the small plug attached to the thin cable on the TST-1080-DSW to the connector located behind the release button on the right of the bezel. Refer to the illustration below step 7. • Contents —...
- Page 7 NOTE: If the bezel must be removed for any reason, disconnect this cable carefully prior to removal. 5. Attach the bezel to the TST-1080-DSW using the four 6-32 x 1 in. screws, but do not tighten the screws. Refer to the illustration below step 7.
- Page 8 7. Attach the four plastic plugs to cover the screws. Each plug should be pushed fully into its opening so that the plug is recessed from the bezel front surface. • Contents — Doc. viii Installation Guide 9338A...
-
Page 9: Dock The Touch Screen
Then, push the cradle back into place to close it. Dock the Touch Screen To dock the TST-1080 touch screen once the TST-1080-DSW has been installed: 1. Push the release button on the right of the bezel to open the cradle. -
Page 10: Undock The Touch Screen
1. Insert the provided release lock key into the gap between the top of the touch screen and the TST-1080-DSW. Ensure that the machined text on the key is facing upward. 2. Rotate the key downward as shown in the following illustration. - Page 11 3. Remove the key to open the cradle so that the touch screen can be removed. — Doc. Contents • Installation Guide 9338A...
- Page 12 • — Doc. TST-1080 Installation Guide 9338A...
- Page 13 This page is intentionally left blank. — Doc. • Installation Guide 9338A TST-1080...
- Page 14 Crestron Electronics, Inc. Installation Guide — Doc. 9338A 15 Volvo Drive, Rockleigh, NJ 07647 01/24/23 Tel: 888.CRESTRON Specifications subject to Fax: 201.767.7656 change without notice. www.crestron.com...
Need help?
Do you have a question about the TST-1080 and is the answer not in the manual?
Questions and answers