Advertisement
Quick Links
ENG
4 wolf pack pro storage system
asymmetric
SSWO010
READ ME !
Thank you for purchasing a Front Runner Modular Storage System.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
SSWO010_REV_A01
1
2023 FRONT RUNNER VEHICLE OUTFITTERS
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Front Runner SSWO010
- Page 1 IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE.
- Page 2 12 X M6 Nut Cap 16 X No.8 x 16 Pan Self-tapping Screw Phillips M6 x 10 Button Head Bolt NOTE: This Unit is broken down into Sub-Assemblies and is marked accordingly. FIGURE 1.1 SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 3 SUB-ASSEMBLY 1 IN THE BOX TOOLS NEEDED Extrusion 915mm Long Corner M6 x 12 Hex Bolt Rubber Mallet M6 Thin Nut FIGURE 2.1 NOTE: Fasteners (Bolts and Nuts) only apply to the Top Frame Assembly. SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 4 Extrusion. This will be the Top Frame. Repeat Steps to assemble another square frame, but leave out the M6 x 12 Hex Bolts and M6 Thin Nuts. This would be the Bottom Frame. Set aside for later use. SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 5 Bottom Tab Bracket M6 x 10 Button Head Bolt M6 x 8 Button Head Bolt 10 X M6 Thin Nut NOTE: Bottom Frame is Similar to the top frame, but with no pre-loaded fasteners. FIGURE 3.1 SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 6 Head Bolts (Item 18). Loosely assemble the Middle Bottom Support and all the Bottom Supports on the opposite side using M6 x 8 Button Head Bolts (Item 20). Tighten all fasteners and put assembly aside. SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 7 SUB-ASSEMBLY 3 IN THE BOX TOOLS NEEDED Extrusion 915mm Long Top Frame assembled in Step 2 Joiner Plate M6 X 12 Hex Bolt M6 x 8 Button Head Bolt M6 Thin Nut FIGURE 4.1 SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 8 Loosely assemble using two M6 x 8 Button Head Bolts (Item 20). Do this for both sides. Align the centre of the Extrusion with the mark made in 4.1, but do not tighten fasten- ers yet. SSWO010_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 9 SUB-ASSEMBLY 4 IN THE BOX TOOLS NEEDED Sub-assembly 3 Corner Bracket Middle Bracket Phillips 16 X No.8 x 16 Pan Self-tapping Screw Bamboo Decking FIGURE 5.1 SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 10 NOTE: Do not over tighten - tighten until snug - if overtightened the screw could pierce through the top of the bamboo. Fully tighten Joiner from Step 4.3. Tightening Torque: M6 : 8-10Nm / 5.9 ft lb - 7.38 ft lb SSWO010_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 11 SUB-ASSEMBLY 5 IN THE BOX TOOLS NEEDED Sub-assembly 4 Spring 12 X M6 Nyloc Nut 10mm 12 X M6 Nut Cap FIGURE 6.1 SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 12 Tightening Torque: M6 : 8-10Nm / 5.9 ft lb - 7.38 ft lb Adjust Springs if necessary and tighten all fasteners. Place M6 Nut Caps (Item 16) over each M6 Nyloc Nut. 10mm SSWO010_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 13 SUB-ASSEMBLY 6 IN THE BOX TOOLS NEEDED Sub-assembly 5 Turn Buckle Carabiner - Large M6 D-Ring M6 x 10 Button Head Bolt Carabiner - Small FIGURE 7.1 SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 14 - and Turn Buckle (Items 11 & 12 or 22) onto the D-Rings for use when installing in the vehicle. Do not tighten fasteners yet, D-Rings should still slide freely in the T-slot. SSWO010_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 15 MAIN ASSEMBLY IN THE BOX TOOLS NEEDED Sub-assembly 6 Extrusion 250mm Long Sub-assembly 2 Rubber Mallet Side Strut 24 X M6 x 8 Button Head Bolts 24 X M6 Thin Nut Corner Gusset FIGURE 8.1 SSWO010_REV_A01 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 16 Load four M6 Thin Nuts (Item 21) into the outer T-Slot on the bottom and top Extrusions parallel to the Bottom Supports, as shown in Fig 8.3. Repeat on the opposite side. SSWO010_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 17 Place the Drawer System in the vehicle and center it. Make sure the Turnbuckles will be pulling outward to the existing mounting points in the vehicle to prevent it from moving after it has been secured. SSWO010_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 18 Drawer System. Make sure the Drawer System stays in position when doing this. Lock the Turn Buckles with the Nuts supplied with the Turn Buckles. Do this by tightening the Nuts up to the Turn Buckle centre part. SSWO010_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
- Page 19 Congratulations! You did it. Take a step back and admire your work! Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.
Need help?
Do you have a question about the SSWO010 and is the answer not in the manual?
Questions and answers