Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Flexabed WIRELESS PREMIER BEDS
Summary of Contents for Flexabed WIRELESS PREMIER BEDS
- Page 1 Operations Manual F O R W I R E L E S S P R E M I E R B E D S www.Flexabed.com...
- Page 2 O F Y O U R N E W F L E X A B E D ! Your Flexabed was custom built by skilled craftsmen in Lafayette, GA using the same principles of quality that we have built our reputation on since 1969. Our beds provide multilevel support in literally thousands of positions for sleeping, watching television, reading or simply relaxing.
- Page 3 Remove any items attached to the bed for shipping purposes. SIDERAILS First remove the hardware carton that is stapled to the underside of the bed HARDWARE (Fig. 1). The hardware carton contains your hand control, casters and/or leg CARTON pads, leg extensions (if ordered), and bed literature. Next, remove the wooden leg pads that are inserted into each bed leg.
- Page 4 Install Your Optional Leg Extensions. Leg extensions are available in one inch increments from 2” to 7” which allows you to raise the overall height of the bed. Leg extensions are an op- tional accessory item. If you ordered leg extensions that are 5” or less in length, they will be located inside the hardware carton that is stapled to the underside of the bed.
- Page 5 We strongly recommend that that you plug your bed into a surge protector to prevent damage to the bed’s electronic components in the event of a power surge in your home’s electrical system. Flexabed’s warranty does not cover damages to the bed as a result of a power surge.
- Page 6 Install mattress retainer bar (if necessary). If you ordered a foundation with a standard-sized mattress this step is not necessary as the mattress retainer bar is installed at the factory. HOWEVER, if you ordered FIG. 7 a foundation only or a foundation and a low profile mattress, you will need to install the mattress retainer bar before using the bed.
- Page 7 O P T I O N A L Attaching a Headboard Your Flexabed does not require a headboard but is equipped with factory installed headboard mounting brackets should you wish to attach one for decorative purposes. The headboard brackets have been mounted at the factory facing inward for FIG.
- Page 8 All Flexabed Premier models ordered with safety rails (except 30” Split beds) come factory equipped with a plate mounting system that facilitates a quick and sturdy installation of your Flexabed safety rails. The only tool needed to complete a safety FIG. 12 rail installation is a 9/16”...
- Page 9 5. Replace the nuts removed in step c and tighten them down with a 9/16” wrench. (Fig. 14) FIG. 15 REMEMBER…your Flex-A-Bed side rail can be lowered to allow for easy entry to and from the bed. Simply pull UP on the side rail and swivel the side rail to the lowered position.
- Page 10 T O P R O G R A M A P R O G R A M M A B L E M E M O R Y B U T T O N Only used when pairing a new remote Remote Flashlight Adjust the bed to your desired position.
- Page 11 If de- ton for the motor that you want to deactivate. sired, you can order a massage system from your Flexabed dealer. To activate the pulse massage mode, press the “Mode” button. The To activate the massage system, press the “ON/OFF”...
-
Page 12: Underbed Lighting
UNDERBED LIGHTING MEMORY POSITIONS: (if equipped): Your Flexabed allows you to store 4 of your own custom memory positions. To program your custom memory position you will All Flexabed Premier remotes come with an underbed lighting con- need to do the following: trol button whether your bed was ordered with underbed lighting •Adjust the bed to the position you want to save to memory... -
Page 14: Sync Button
HAND CONTROL SYNCING (wireless remote only): If your bed is equipped with a wireless remote, the remote is automatically synced to your bed at the factory during the manufacturing process. In the event that you order a new replacement remote or a new control box in the future, you will have to sync the wireless remote to your control box. -
Page 15: Backup Battery Power
Backup battery power: Each Flexabed power supply is equipped to supply emergency bed lowering capability via battery power. EMERGENCY BATTERY POWER IS OPTIONAL – THE BED WILL FUNCTION PROPERLY WITH OR WITHOUT BATTERIES IN THE POWER SUPPLY. In order to use backup battery power, you will need to install two 9V batteries (not included) into the emergency battery compartment (Fig. - Page 16 As stated earlier in this manual, all cables are set up and are using to supply power to your bed and/or connected at the factory when your Flexabed is built. power strip is in working order. It is a good idea However, those cables can become discon- to plug a known working electrical device (i.e.
-
Page 17: Power Supply Connections
1. Power Supply Connections. PLUG IN TO The first place to check your wiring connections is at the power supply. Your ELECTRICAL OUTLET bed’s power supply is attached to the bed’s platform on the underside of the head section of the bed. The power supply is a small black box that plugs in to your home’s wall receptacle to supply electrical power to the bed. -
Page 18: Control Box Connections
2. Control Box Connections. The control box is the “brain” of your Flexabed which allows the hand control to communicate with all of the motors on your bed. If any motor or accessory item on your bed is not working, check all of the ports on the control box to make sure that connections are configured properly. - Page 20 V O I C E A C T U AT I O N C O N T R O L The voice control module (VCM) allows a bed user to control all of the functions on their Flexabed without the use of a traditional hand-held remote control.
- Page 21 V O I C E C O M M A N D S (words in parentheses are for instruction only - they are not spoken) Head Up Save Position 2 Timer 10 The VCM is automatically programmed to (to set massage timer to 10 mins) “Max”...
-
Page 22: Installation Instruction
BLUETOOTH CONNECTIVY: Your Flex-A-Bed can be controlled with any Bluetooth enabled Android or Iphone device by downloading the Okin SmartBed app. To download the SmartBed app, scan B L U E T O O T H C O N N E C T I O N the following QR code or search “Okin SmartBed”... - Page 23 • Navigate to the screen titled “POSITION” (Figure 21) • Click on the 3 horizontal bars in the upper left corner of the screen • At the bottom of the screen, select the “Bluetooth” option (22) • You should see a device named “SmartBed” in the device list. Click on the Smart Bed device to pair your device with your bed.
- Page 24 P O S I T I O N S C R E E N . The position screen is similar to the layout on your remote control Your regular remote only has four programmable memory but- with a few exceptions. tons (M1, M2, M3, M4).
-
Page 25: Alarm Screen
MASSAGE SCREEN ALARM SCREEN This screen allows you to change the settings on your bed’s mas- The alarm screen allows you set an alarm for a specified time sage system using the Smart Remote app. (Figure 24) and day(s) of the week that will wake you by using one the bed’s •... -
Page 26: Limited Lifetime Warranty
Flexabed, has been altered or re- • When you are finished editing your alarm settings, paired by an unauthorized representative in any way that affects the press the blue button at the bottom of the screen reliability or detracts from the performance of the product. - Page 27 • During the first 12 months after purchase, Flexabed will provide in Flexabed will offer an “in-lieu of” discount of 33% off the MSRP that is home repairs or replacement at the factory’s option at no charge in effect at that time toward the purchase of a new mattress or articu- provided the defect is demonstrated to be a defect in materials or lating base unit.
- Page 28 We’re based in friendly LaFayette, Georgia. 1-800-648-1256 | info@flexabed.com www.Flexabed.com...