Advertisement
PROGRAMMING DISPLAY
The electronic lube meter liquid crystal
display may be programmed
for Eng-
lish or Metric increments.
Perform the
following procedure to change the units
of measure.
A.
B.
C,
D.
E.
Remove three screws attaching
register module to the meter
housing.
Press and hold PROGRAMMING
switch located on bottom of mod-
ule. Unit of measure will flash.
Press RESET switch until desired
unit appears.
Release PROGRAMMING
switch.
Reinstall register module in
meter housing and tighten
screws.
OPERATION
After all entrapped air and/or foreign par-
ticles are removed
from the supply
line,
clean
oil continuously
passes
through the metering chamber by enter-
ing the inlet port, displacing the piston,
and exiting the outlet port. Each oscilla-
tion of the piston displaces a given vol-
ume of fluid. Controlled clearances be-
tween the piston and chamber wall in-
sure accurate measurements.
As the
piston oscillates, its center hub rotates a
magnet which activates the microproces-
sor.
Depress the RESET button with your
thumb to reset the totalizer to zero before
each use. Squeeze the trigger handle to
dispense the desired amount of fluid.
Total amount used from inventory can
be check periodically by depressing the
TOTAL button If the units dispensed are
pints, quarts, or gallons, the totalizer will
read in gallons.
If the units dispensed
are liters, the totalizer will read in liters.
TROUBLE SHOOTING
All meters are shipped
with a unit of
measure preprogrammed
at the factory.
A built in "error detection"
feature will
cause the numbers on the LCD to flash if
the microprocessor does not receive the
proper pulse rate. If this should occur,
the entire register
module should be
replaced. Refer to REPAIR.
LIMITED WARRANTY
Lincoln, A Pentair Company, warrants that lubrication equipment, materials dispensing
equipment and other related equipment manufactured by it will be free from defects in
material and workmanship during the one (1) year following the date of purchase.
If
equipment
proves to be defective during this warranty period, it will be repaired or
replaced without charge, provided that factory examination indicates the equipment to
be defective.
To obtain repair or replacement,
it must be shipped, transportation
charges prepaid, with proof of date of purchase to a Lincoln authorized Warranty and
Service Center, within the one (1) year following the date of purchase.
This warranty is extended to the original retail purchaser only. This warranty does not
apply to equipment damaged from accident, overload, abuse, misuse, negligence,
faulty installation or abrasive or corrosive materials, or to equipment repaired or altered
by anyone not authorized by Lincoln to repair or alter the equipment.
This warranty
applies only to equipment installed and operated according to the recommendations of
Lincoln or its authorized field personnel. No other express warranty applies to lubrica-
tion equipment, materials dispensing equipment
and other related equipment manu-
factured by Lincoln.
ANY IMPLIED WARRANTIES
applicable
to lubrication
equipment,
materials dis-
pensing equipment and other related equipment manufactured by Lincoln INCLUDING
THE WARRANTIES
OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE,
WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF PUR-
CHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IM-
PLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
In no event shall Lincoln be liable for incidental or consequential damages. The liabil-
ity of Lincoln on any claim for loss or damage arising out of the sale, resale, or use of
lubrication equipment, materials dispensing equipment, and other related equipment
shall in no event exceed the purchase price. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
2
Advertisement
