actionair MRC-I01CS Operation Manual

Vrf infra red controller

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Table of Contents

Need help?

Do you have a question about the MRC-I01CS and is the answer not in the manual?

Questions and answers

Summary of Contents for actionair MRC-I01CS

Page 3 Thank you for purchasing this remote controller. Carefully read this OPERATION AND INSTALLATION MANUAL before using the controller. It will tell you how to use the controller properly and help you if any trouble occurs. After reading the manual, please keep it for future reference.
Page 4: Table Of Contents
Contents Installation ..............1 1. Installation Precautions ........1 2. Installation Accessories ........3 3. Dimensions of Remote Controller and Bracket 4. Installation and Fixing ........4 5. Replace the Batteries ........5 Operating the Remote Controller ......7 1. Using Precautions ..........7 2.
Page 5: Installation
Installation 1. Installation Precautions Safety Considerations Please read this "Safety Considerations" carefully before installing Controller and be sure to install it correctly. After completing the installation, make sure the controller operates properly. Please instruct the customer how to operate the controller and how to perform maintenance.
Page 6 Installation WARNING Precautions in handling remote controller • Direct the transmitting part of the remote controller to the receiving part of the air conditioner. • If something blocks the transmitting and receiving path of the indoor unit and the remote controller as curtains, it will not operate. •...
Page 7: Installation Accessories
Installation 2. Installation Accessories • Please check that you have all the following parts. Schematic Name Remote controller bracket ① Screw lid ② Philips head screw (M2.9*12) ③ AAA battery ④ Remote controller manual ⑤ 3. Dimensions of Remote Controller and Bracket 25 mm 47 mm Figure 2.1 Dimensions of remote controller...
Page 8: Installation And Fixing
Installation 25 mm 72 mm Figure 2.2 Dimensions of remote controller bracket 4. Installation and Fixing 1) Use the screws (accessories) to fix and secure the remote controller bracket in a stable position (see Figure 2.3); Make sure you refer to "1. Installation Precautions" to determine the location.
Page 9: Replace The Batteries
Installation Figure 2.4 3) Slide the remote controller vertically down into the remote controller bracket (see Figure 2.5). Figure 2.5 5. Replace the Batteries 1) Slide to move the battery cover at the back of the remote controller in the direction indicated by the arrow (Figure 2.6);...
Page 10 Installation Figure 2.6 2) Lift up from the lower left end of the battery cover to open it (see Figure 2.7); Figure 2.7 3) Take out the old batteries. Install two new AAA batteries according to the positive and negative polarities indicated (see Figure 2.8). Close the battery cover.
Page 11: Operating The Remote Controller
Operating the Remote Controller 1. Using Precautions To gain full advantage of the controller's functions and to avoid malfunction due to mishandling, we recommend that you read this instruction manual carefully before use. The precautions described herein are classified as WARNING and CAUTION.
Page 12: Model And Key Parameters
Operating the Remote Controller CAUTION • Do not operate the device with wet hands to prevent water from entering the remote controller and damage the circuit board. • Do not use the air conditioner for purposes other than those for which it is intended.
Page 13: Button Names And Functions
Operating the Remote Controller 3. Button Names and Functions Figure 3.1 External view of remote controller...
Page 14 Operating the Remote Controller Button Function Turn on/off the ETA function ETA function ① Set operating mode: Cool → Mode ② Dry→ Fan→ Heat Adjust the temperature setting Adjust downwards or timer (programmed time) ③ downwards In Cool mode, press this button ④...
Page 15: Name And Function On Display Screen
Operating the Remote Controller Note: • The buttons are not available for first generation indoor units. • The button is only available for indoor unit with individual vane control function. • is only available for indoor unit with soft wind function. 4.
Page 16: Operating Methods
Operating the Remote Controller Self cleaning Shows Self cleaning function is on ⑨ Horizontal swing Shows that Horizontal Swing is on ⑩ Vertical swing Shows that Vertical Swing is on ⑪ Shows that the remote controller Lock ⑫ button is locked Shows that ETA function is on ETA function ⑬...
Page 17: Fan Speed Operations
Operating the Remote Controller 2) Press each time to change the operating mode according to the order shown in Figure 3.5; Cool Heat Figure 3.5 3) In Cool, Dry or Heat mode, press ▲ and ▼ to adjust the tempera- ture setting.
Page 18: Soft Wind Operations
Operating the Remote Controller 5.4 Soft Wind Operations Press to adjust the direction of the vertical louver (see Figure 3.9). Figure 3.9 ① In Cool mode, press this button to turn on or off the Soft wind function. ② In Soft wind function, the fan operates at the minimum speed and swings at the minimum angle.
Page 19: Idu Display Operations
Operating the Remote Controller ② When the vertical swing is on, press to turn off this function. Note: • When the unit is turned off, the button is invalid. • Each time the vertical swing signal is sent, the icon keeps lighting up for 15s and then disappears.
Page 20: Silent Mode Operation
Operating the Remote Controller 2) When the display of the indoor unit lights up, press to turn off the light. 5.8 Silent Mode Operation The Silent function is used by the remote controller to send the "Silent" signal to the indoor unit. The indoor unit automatically optimizes the noise it generates when it is in the "Silent"...
Page 21: Sterilize Function Operations
Operating the Remote Controller Note: • When ETA function is set up, the Fan Speed is forced to Auto. • Once it has been running for 8 hours, will no longer light up. • The Silent and ETA function cannot be implemented at the same time.
Page 22: Self Cleaning Operation
Operating the Remote Controller 2) When the unit is powered off: ① Press (see Figure 3.17), and the remote controller will display "Timer On", and "0.0H" will appear in timer area. Adjust the Timer On settings now; ② Press to adjust the timer settings; ③...
Page 23: Button Lock Operations
Operating the Remote Controller 5.13 Button Lock Operations Once the buttons on the remote controllers are locked, all the other button operations except for Unlock and IDU Address Setting are invalid. 1) Press at the same time to lock the button (see Figure 3.19), and the screen will display the lock icon 2) Press at the same time, and the lock icon...
Page 24: Field Settings
Field Settings 1.Initial Parameter Configuration for Remote Control- 1) Configuration Method: ① Long press on the remote controller at the same time for 8 seconds to go to the parameter settings status (see Figure 4.1); Figure 4.1 ② Press ▲ and ▼ to adjust the parameter value; ③...
Page 25 Field Settings Figure 4.2 2) See Table 4.1 for details. Table 4.1 Parameters of remote controller Parameter Parameter Definition 7 fan speeds, temperature adjustment step of 0.5°C(default parameter) 3 fan speeds, temperature adjustment step of 1°C 7 fan speeds, temperature adjustment step of 1°C 3 fan speeds, temperature adjustment step of 0.5°C...
Page 26: Advaced Parameter Configuration
Field Settings 2.Advanced Parameter Configuration for Remote Controller 1) Configuration Method: Parameters can be set in the state of power on or off. ① Long press on the remote controller at the same time for 8 seconds to go to the advanced parameter settings status,"C1" will be displayed in the temperature display area(see Figure 4.3);...
Page 27 Field Settings Figure 4.4 ④ Parameter query: press the to send the query code, and the indoor unit display board displays the parameter code; ⑤Parameter setting: press the key to send the setting code; ⑥Press the to return to the previous layer until you exit the parameter setting;...
Page 29 Field Settings Note: ①FF: FF means that this setting has a corresponding dial switch on the IDU PCB and the position of the switch determines the value of this parameter. ②Default Value: It means this parameter does not have a dial switch on the main PCB and in case of no setting, the default value shall prevail;...
Page 30: Indoor Units Parameter Check Function
Field Settings 3.Indoor Units Parameter Check Function In the state of power on or off, long press the together for 8 seconds to enter the parameter setting page, then press the to send the command,and the indoor unit display will show the IDU current parameters corresponding to particular IDU model, for more information refer to IDU installation and operation instruction.