Advertisement
Quick Links
Advertisement
Related Manuals for NCR 7360-K074
Summary of Contents for NCR 7360-K074
- Page 1 Kit Instructions IP Camera (Standard) Field Upgrade 7360-K074 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a customer’s installed software exactly.
- Page 3 Revision Record Issue Date Remarks Aug 2022 First Issue...
- Page 4 IP Camera Field Upgrade (Standard) This publication provides procedures for installing the IP Camera Field Upgrade (Standard) to the NCR FastLane SelfServ™ Checkout (7360). Kit Contents Part Number Description 497-0532762 Kit - IP Camera Field Upgrade (Standard) 497-0532090 Tri-Light Cable Channel Bracket...
- Page 5 IP Camera Field Upgrade (Standard) Part Number Description 006-8624498 Screw - M4x.7x8mm, Flat Head, Stainless 007-9714414 Tie Strap Plain 5.60LG 497-0519622 Label - Hole Cover, Mid - Silver (3 pcs) 497-0423108 Instructions Kit (Reference Sheet) * Items marked with an asterisk are not called out on the image. Customer Supplied Devices The following devices must be supplied by the customer: •...
- Page 6 Installation Procedure To install the IP Camera Field Upgrade (Standard), follow these steps: Note: Ensure that the NCR Customer Helpdesk is informed when the Tri-Light/Lane Light with IP Camera is installed in the store. 1. Remove the existing Tri-Light/Lane Light Assembly, if necessary. For more...
- Page 7 IP Camera Field Upgrade (Standard) Removing the Tri-Light/Lane Light (R6) To remove the Tri-Light/Lane Light Assembly, follow these steps: 1. Turn off the NCR SelfServ Checkout software and hardware systems. For more information, refer to the NCR SelfServ™ Checkout (7360) Hardware Service Guide (B005–0000–2378).
- Page 8 IP Camera Field Upgrade (Standard) 3. Lift the Tri-Light/Lane Light Assembly and then disconnect the cables. Tip: Mark all cables as to where they are connected to quickly determine the corresponding port when reconnecting the cables.
- Page 9 IP Camera Field Upgrade (Standard) Installing the IP Camera To install the IP Camera (Standard) to the Tri-Light/Lane Light Assembly, follow these steps: 1. Remove the existing Tri-Light/Lane Light Assembly. For more information, refer to Removing the Tri-Light/Lane Light (R6) on page 4. 2.
- Page 10 IP Camera Field Upgrade (Standard) 3. Secure the LAN Cable to the Tri-Light Cable Channel Bracket using four (4) cable ties, as shown in the image below. 4. Slide the Tri-Light C-clamp Bracket on the new Tri-Light/Lane Light Assembly.
- Page 11 IP Camera Field Upgrade (Standard) 5. Slide the Tri-Light Cable Channel Bracket on the new Tri-Light/Lane Light Assembly.
- Page 12 IP Camera Field Upgrade (Standard) 6. Secure the Tri-Light Cable Channel Bracket to the Tri-Light/Lane Light Assembly using two (2) screws.
- Page 13 Installing the Tri-Light/Lane Light with IP Camera Assembly To install the new Tri-Light/Lane Light with IP Camera Assembly, follow these steps: Note: Ensure that the NCR Customer Helpdesk is informed when the Tri-Light/Lane Light with IP Camera is installed in the store. 1. Remove the existing Tri-Light/Lane Light Assembly, if necessary. For more...
- Page 14 IP Camera Field Upgrade (Standard) 5. Insert the Tri-Light/Lane Light Assembly into the Tri-Light/Lane Light Pole. Ensure that the pole holes are aligned. Note: Ensure that the LAN Cable and the Tri-Light/Lane Light Cable do not intertwine when installing the Tri-Light/Lane Light assembly to the Tri-Light/Lane Light Pole.
- Page 15 IP Camera Field Upgrade (Standard) 8. Attach three (3) Label-Hole Covers to the holes on the Tri-Light/Lane Light, as show in the image below.
- Page 16 IP Camera Field Upgrade (Standard) Routing the Cables The steps for routing the Tri-Light/Lane Light and LAN cable depend on the SelfServ Checkout configuration. For more information, refer to the following procedures: • Routing the Cables: 7360 R6-C Full Function (Fixed) on the next page.
- Page 17 IP Camera Field Upgrade (Standard) Routing the Cables: 7360 R6-C Full Function (Fixed) To route the Tri-Light/Lane Light Cable and LAN Cable in the Full Function (Fixed) unit, follow these steps: 1. Do the following: a. From the Tower Frame pole duct, route the Tri-Light/Lane Light Cable through the built-in hooks inside the Tower Frame.
- Page 18 IP Camera Field Upgrade (Standard) 2. Route the Tri-Light/Lane Light Cable by doing the following: a. From the corner cable access hole, route the cable down the Core Cabinet wall and use cable ties to secure the cables on the bridge lances. b.
- Page 19 IP Camera Field Upgrade (Standard) No-Bag Unit: 7360 R6-C Full Function (Fixed) To route the LAN Cable, follow these steps: 1. Do the following: a. From the Tower Frame pole duct, route the cable down through the built-in hooks inside the Tower Frame. b.
- Page 20 IP Camera Field Upgrade (Standard) 2. From the corner cable access hole, route the cable down the Core Cabinet wall and down the bottom exit hole, as shown in the image below. Note: Pass the cable through cable clamps and secure the cable on the bridge lances using cable ties.
- Page 21 IP Camera Field Upgrade (Standard) Left-Hand Unit: 7360 R6-C Full Function (Fixed) To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route cable down the Scanner Bucket and out through the rear cable access hole.
- Page 22 IP Camera Field Upgrade (Standard) 2. From the rear cable access hole, route the cable down the rear of the Core Cabinet and into the Bagwell through the left side cable exit hole. Use cable ties to secure the cable to the lance bridges. 3.
- Page 23 IP Camera Field Upgrade (Standard) Right-Hand Unit: 7360 R6-C Full Function (Fixed) To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route the cable down the Scanner Bucket and out through the rear cable access hole.
- Page 24 IP Camera Field Upgrade (Standard) 2. From the rear cable access hole, route the cable down the rear of the Core Cabinet and into the Bagwell through the right side cable exit hole. Use cable ties to secure the cable to the lance bridges. 3.
- Page 25 IP Camera Field Upgrade (Standard) Routing the Cables: 7360 Full Function (Convertible) To route the Tri-Light/Lane Light Cable and LAN Cable in the 7360 Full Function (Convertible) unit, follow these steps: 1. Do the following: a. From the Tower Frame pole duct, route the Tri-Light/Lane Light Cable and the LAN Cable down through the built-in hooks inside the Tower Frame.
- Page 26 IP Camera Field Upgrade (Standard) d. Continue to route the cables into the corner cable access hole. 2. Route the Tri-Light/Lane Light Cable by doing the following. a. From the corner cable access hole, route the cable down the Core Cabinet wall and use cable ties to secure the cables on the bridge lances.
- Page 27 IP Camera Field Upgrade (Standard) 3. Route the LAN Cable. Depending on the unit configuration, refer to the following: • No-Bag: 7360 Full Function (Convertible) on the facing page. • Left-Hand Unit: 7360 Full Function (Convertible) on page 26. • Right-Hand Unit: 7360 Full Function (Convertible) on page 28.
- Page 28 IP Camera Field Upgrade (Standard) No-Bag: 7360 Full Function (Convertible) To route the LAN Cable, follow these steps: 1. From the corner cable access hole, route the cable down the Core Cabinet wall and down the bottom exit hole, as shown in the image below. Note: Pass the cable through cable clamps and secure the cable on the bridge lances using cable ties.
- Page 29 IP Camera Field Upgrade (Standard) Left-Hand Unit: 7360 Full Function (Convertible) To route the LAN Cable, follow these steps: 1. From the corner cable access hole, route the cable down the Core Cabinet wall and through the cable access hole, as shown in the image below. Note: Pass the cable through cable clamps and secure the cable on the bridge lances using cable ties.
- Page 30 IP Camera Field Upgrade (Standard) 2. Continue to route the cable into Bagwell through the left side exit hole and out through the bottom cable exit hole of the Bagwell. 3. Connect the cable to the PoE Switch.
- Page 31 IP Camera Field Upgrade (Standard) Right-Hand Unit: 7360 Full Function (Convertible) To route the LAN Cable, follow these steps: 1. From the corner cable access hole, route the cable down the Core Cabinet wall and through the cable access hole, as shown in the image below. Note: Pass the cable through cable clamps and secure the cable on the bridge lances using cable ties.
- Page 32 IP Camera Field Upgrade (Standard) 2. Continue to route the cable to Bagwell through the right side exit hole and out through the bottom cable exit hole of the Bagwell. 3. Connect the cable to the PoE Switch.
- Page 33 IP Camera Field Upgrade (Standard) Routing the Cables 7360 R6-C (Card Only) To route the Tri-Light/Lane Light Cable and LAN Cable in the R6-C Card Only unit, follow these steps: 1. Do the following: a. From the Tower Frame pole duct, route the Tri-Light/Lane Light Cable and the LAN Cable down through the built-in hooks inside the Tower Frame.
- Page 34 IP Camera Field Upgrade (Standard) 2. Route the Tri-Light/Lane Light Cable by doing the following: a. From the corner cable access hole, route the cable down the Core Cabinet wall and use cable ties to secure the cables on the bridge lances. b.
- Page 35 IP Camera Field Upgrade (Standard) No-Bag: 7360 R6-C Card Only To route the LAN Cable, follow these steps: 1. From the corner cable access hole, route the cable down the Core Cabinet wall and down the bottom exit hole, as shown in the image below. Note: Pass the cable through cable clamps and secure the cable on the bridge lances using cable ties.
- Page 36 IP Camera Field Upgrade (Standard) Left-Hand Unit: 7360 R6-C Card Only To route the LAN Cable, follow these steps: 1. From the corner cable access hole, route the cable down the Core Cabinet wall and through the cable access hole, as shown in the image below. Note: Pass the cable through cable clamps and secure the cable on the bridge lances using cable ties.
- Page 37 IP Camera Field Upgrade (Standard) 2. Continue to route the cable into the Bagwell through the left side exit hole and out through the bottom cable exit hole of the Bagwell. 3. Connect the LAN Cable to the PoE Switch.
- Page 38 IP Camera Field Upgrade (Standard) Right-Hand Unit: 7360 R6-C Card Only To route the LAN Cable, follow these steps: 1. From the corner cable access hole, route the cable down the Core Cabinet wall and through the cable access hole, as shown in the image below. Note: Pass the cable through cable clamps and secure the cable on the bridge lances using cable ties.
- Page 39 IP Camera Field Upgrade (Standard) 2. Continue to route the cable to the Bagwell through the right side exit hole and out through the bottom cable exit hole of the Bagwell. 3. Connect the LAN Cable to the PoE Switch.
- Page 40 IP Camera Field Upgrade (Standard) Routing the Cables: 7357 R6LN Plus To route the Tri-Light/Lane Light Cable and the LAN Cable in the 7357 unit, follow these steps: 1. Route the Tri-Light/Lane Light Cable by doing the following: a. From the Tri-Light/Lane Light Pole, route the cable down to the cable access hole on the back of the unit, as shown in the image below.
- Page 41 IP Camera Field Upgrade (Standard) b. Connect the cable to the Tri-Light/Lane Light port of the I/O Box, as shown in the image below. c. Secure the cable to the lance bridges using cable ties. 2. Route the LAN Cable. Depending on the unit configuration, refer to the following: •...
- Page 42 IP Camera Field Upgrade (Standard) No-Bag Unit: 7357 R6LN Plus To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route the cable down the rear of the Core Cabinet and out through the side cable exit hole. Use a cable tie to secure the cable to the vent.
- Page 43 IP Camera Field Upgrade (Standard) 2. Connect the cable to the PoE Switch.
- Page 44 IP Camera Field Upgrade (Standard) Left-Hand Unit: 7357 R6LN Plus To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route the cable down the rear of the Core Cabinet. Use a cable tie to secure the cable to the vent. Note: Apply enough cable slack to prevent the cable from being stretched during installation or removal procedures.
- Page 45 IP Camera Field Upgrade (Standard) Right-Hand Unit: 7357 R6LN Plus To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route the cable down the rear of the Core Cabinet. Use a cable tie to secure the cable to the vent. Note: Apply enough cable slack to prevent the cable from being stretched during installation or removal procedures.
- Page 46 IP Camera Field Upgrade (Standard) Routing the Cables: 7358 R6L Plus To route the Tri-Light/Lane Light Cable and the LAN Cable in the 7358 unit, follow these steps: 1. Route the Tri-Light/Lane Light Cable by doing the following: a. From the Tri-Light/Lane Light Pole, route the cable up into the Upper Cabinet. Note: Apply enough cable slack to prevent the cable from being stretched during installation or removal procedures.
- Page 47 IP Camera Field Upgrade (Standard) b. Secure the cable to the Upper Cabinet frame using cable ties. c. Connect the cable to the Tri-Light/Lane Light port of the I/O Box. 2. Route the LAN Cable. Depending on the unit configuration, refer to the following: •...
- Page 48 IP Camera Field Upgrade (Standard) No-Bag Unit: 7358 R6L Plus To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route the cable down the rear of the Core Cabinet and out through the side cable exit hole. Note: The LAN Cable can exit either through the left or the right side cable exit hole depending on the customer's preference.
- Page 49 IP Camera Field Upgrade (Standard) 2. Connect the cable to the PoE Switch.
- Page 50 IP Camera Field Upgrade (Standard) Left-Hand Unit: 7358 R6L Plus To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route the cable down the rear of the Core Cabinet, through the side cable exit hole and into the Bagwell 2.
- Page 51 IP Camera Field Upgrade (Standard) Right-Hand Unit: 7358 R6L Plus To route the LAN Cable, follow these steps: 1. From the Tri-Light/Lane Light Pole, route the cable down the rear of the Core Cabinet, through the side cable exit hole and into the Bagwell 2.
- Page 52 IP Camera Field Upgrade (Standard) Configuring the Camera Settings To configure the camera settings, follow these steps: 1. Connect the STP Ethernet Cable from the Tri-Light IP Camera Port to a POE Switch. 2. Connect another LAN Cable from the host to same POE Switch. 3.
- Page 53 IP Camera Field Upgrade (Standard) c. Enter the following default login credentials: Username: admin Password: 123456 A download link to the plugin is displayed on the Camera View user interface, as shown in the image below. 4. Click the link to download the plug-in. The browser opens a live feed of the camera, as shown in the image below.
- Page 54 Left-hand (LH) unit. For more information on setting the camera parameters, refer to VTC Network Camera User Manual. Note: Ensure that the NCR Customer Helpdesk is informed when the Tri-Light/Lane Light with IP Camera is installed in the store.