Summary of Contents for Perfect Fit FE-AM3-16P3-WB
- Page 1 AC EV Charging Station Manual Before operating this product, please read the operating instruction carefully...
-
Page 2: Table Of Contents
CONTENTS 1.Safe Use Guide ------------------------------------------------------------------------ 2.Product Picture ------------------------------------------------------------------------ 3.Product Features/Basic Information --------------------------------------- 4.Installation Steps --------------------------------------------------------------------- 5.Charging Steps ------------------------------------------------------------------------ 6.Key Operation Steps --------------------------------------------------------------- 7.Charging Status and LED Definition --------------------------------------- 8.Trouble Shooting ------------------------------------------------------------------- 9.Adding Device ------------------------------------------------------------------------------ 10.App Function ------------------------------------------------------------------------... -
Page 3: Safe Use Guide
Safe Use Guide When using the charging station, please read all instructions carefully before: 1) Do not bring flammable, explosive or combustible materials, chemicals, combustible vapors and other dangerous items near the charging station。 2) Keep the charging gun head clean and dry, wipe it with a clean dry cloth if it is dirty, and it is strictly forbidden to touch the charging gun core by hand when it is charged。... -
Page 4: Product Picture
Product Overview LED light LCD display Touch Button RFID Cable Type2 plug... -
Page 5: Product Features/Basic Information
Product Features 1. With RFID function to start or stop charging. 2. Connect to APP via Bluetooth or WIFI. 3. With the function of appointing charging time and appointing charging duration. 4. Equipped with display screen to show charging information in real time. 5. -
Page 6: Installation Steps
Installation Steps Step 2 :Installation of charging station. Step 1 :According to the size of the steel plate’s inlet. hole, using an electric drill to drill a hole in the wall at a suitable height, then put in the expansion tube. -
Page 7: Charging Steps
Step 5: Turn on the power to confirm that the LED Step 6: Try to start charging by inserting light and the display start normally. the gun and swiping the card. Charging Steps Standby status : (1) In the standby state of the charging station, the interface shows that the device has entered the ready charging state, as shown in the following picture. - Page 8 Start-up device : (3)Use RFID cards to authorize the use of charging station. Start charging : (4) The device starts charging and the interface displays the charging status and information parameters as shown in the flowing picture. The LED light on the station (for WIFI function only) is green breathing. Stop charging : (5.1) When the vehicle is fully charged, the charging station will automatically stop charging;...
- Page 9 (5.3)When charging is finished, the end interface has two displays,as shown in the following pictures. Non-active card swipe to end charging Active swipe to stop charging The LED light on the station (for WIFI function only) is green flashing or green always on.
-
Page 10: Key Operation Steps
Key Operation Instructions Enable or disable the card swipe function：Before the charging gun is inserted, long press the first button for 5 seconds to set the opening or closing of the card swiping function. Setting the current adjustment function: Touch the second button to adjust the current, the current can be set 8A 10A 13A 16A. -
Page 11: Charging Status And Led Definition
Charging Status and LED Definition... -
Page 12: Trouble Shooting
Trouble Shooting The fault name Symptom Possible causes AC over voltage AC input voltage too high Rule out advice 1.If the voltage exceeds 457Vac for a short time,wait for the power grid to restore itself to the normal voltage range. 2.Check the background monitoring data and analyze, if this area is over-voltage for a long time, the input over voltage protection point can be increased through the configuration software, up to 457Vac. - Page 13 Symptom Possible causes The fault name Leakage current exceeds High leakage current to the ground standard Rule out advice 1. Immediately turn off the leakage/over current protection switches in the power distribution box. 2.Check whether the output line of AC st ation is damaged or has low impedance to the ground.
-
Page 14: Adding Device
Adding Device 1) Application download Download Tuya Smart App from the App Store 2) Configure the charging device network Ensure that the charging device and the mobile phone are in the same Wifi network (5G band Wifi is not currently supported) and that the phone located near the charging device. - Page 15 Demonstration of distribution network operation process: Step 3： Step 2： Step 1： Add Enter Turn on WIFI&Bluetooth Add Device Step 4： Step 5： Step 6： Waitting Next Done...
-
Page 16: App Function
App Function Charging Finish Charging Connect Set Chargetime Set Delaytime Set Current...
Need help?
Do you have a question about the FE-AM3-16P3-WB and is the answer not in the manual?
Questions and answers
The charcher wil not start by RFID
The Perfect Fit FE-AM3-16P3-WB charger may not start with RFID due to the following reasons:
1. Card Swipe Function Disabled – If the card swipe function is disabled, the RFID card will not work. To enable it, long press the first button for 5 seconds before inserting the charging gun.
2. Appointment Charging Set – If an appointment charging time is set, the charger will only start after the specified delay (0 to 15 hours).
3. Charging Time Not Set Properly – If the charging time is not set correctly, the device may not start charging as expected.
4. Fault Conditions – Issues such as AC input voltage being too low, overcurrent, over-temperature, leakage current, or ground faults could prevent charging. These issues should be checked and resolved.
5. Non-Active RFID Card – If a non-active RFID card is used, it may not start charging. An active card must be swiped to begin.
Checking these factors can help in troubleshooting why the charger won't start with RFID.
This answer is automatically generated
My charger will only charge with 3,5kw on one power face L1. L2 and L3 delivered only 0,6kw