Summary of Contents for Nisshinbo Micro Devices NJR2935 Series
Page 1
Microwave Business Headquarters -Notice of Proprietary Information- This document and its contents are proprietary to Nisshinbo Micro Devices Inc. This publication and its contents may not be reproduced or distributed for any other purpose without the written permission of Nisshinbo Micro Devices Inc.
Page 2
Caution 1. While Nisshinbo Micro Devices Inc. (NISD) continually strives to improve the quality and reliability of our products, failures will occur in microwave products over time. For this reason, it is important that customers fulfill their responsibilities to ensure designed-in safety –...
Page 3
NJR2935 series Scope This LNB is designed for the low noise amplifier and block downconverter intended for the satellite communication data downlink application in Ku-band. It is combined a 3-stage HEMT amplifier and a block downconverter with a phase locked local oscillator (10 GHz, 10.25 GHz, 10.75 GHz, 11.25 GHz, or 11.3 GHz) which is synchronized with external 10MHz reference.
Page 4
NJR2935 series Series Model Number Numbering System Line-up *Above Specifications are subject to change without notice. Reference No.: Rev.: Sheet: DS-R2935...
NJR2935 series 4. Outline Drawing 4.1. F-type Model (e.g. NJR2935E) 4.2. N-type Model (e.g. NJR2935EN) *Above Specifications are subject to change without notice. Reference No.: Rev.: Sheet: DS-R2935...
Page 9
NJR2935 series 5. Label 5.1. Label Outline (e.g. NJR2935E) 5.2. Definitions Serial Number (OSSSSSRYM) - ALPHANUMERIC (9 characters) A 0 0 0 0 1 A 1 3 M: Prodctuon Month Y: Prodctuon Year R: Revision Number SSSSS: Running Number O: Overflow Number O: Overflow Number - ALPHABET (1 character) "A"...
Page 10
NJR2935 series 6. Package 6.1. Individual Package / Shipping Package *Above Specifications are subject to change without notice. Reference No.: Rev.: Sheet: DS-R2935...
Page 11
NJR2935 series 6.2. Enclosed Accessories O-ring Gasket, Qty (1), Full-type, for Waveguide Flange Screws, Qty (4), M4 x 10 mm, Phillips Head with Spring Washer and Flat Washer, SUS *Above Specifications are subject to change without notice. Reference No.: Rev.:...
NJR2935 series 7. Handling Precautions 7.1. DANGER This statement indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Items Description Input Voltage Only input a DC voltage within the range indicated in specifications.
Page 13
NJR2935 series Items Description Weatherproof The unit mounted in outdoor should be conducted with adequately weatherproof procedure. Do seal all of cable connection points from the connector to the cable sheath by usage of self-amalgamating tape. Ensure the waveguide connection is properly assembled with the supplied o-ring gasket as accessories.
Page 14
NJR2935 series 8. Instructions Manual 8.1. Descriptions This section describes the information of connectors and etc. Items Description Purpose RF Input Waveguide: WR-75 The LNB receives an RF signal (Ku-band: frequency Waveguide Flange: Square Cover divided by region band from the 10.75 to 12.75 GHz) via Grooved this waveguide.
Page 15
NJR2935 series 8.2.1. Mounting Configuration The Unit can be mounted with OMT or the waveguide filter of the satellite antenna. When mounting with the OMT or the waveguide filter, the following steps should be complied: Step 1: Verify that the groove on the waveguide flange for a gasket is clean.
Page 16
NJR2935 series 8.2.2. Connecting Coaxial Cable The LNB is connected the modem with a coaxial cable, and requires to supply +12 to +24 V DC power and a 10 MHz reference from the modem. The connection of coaxial cable should be complied with the following steps:...
Page 17
NJR2935 series 8.2.3. Start-up Start-up will be immediately performed with the following step: Step: Power on the modem and supply the DC voltage and 10 MHz reference from modem. Only input a DC voltage within the range indicated in specifications.