Related Manuals for AXIOMTEK TEN100 Series
Summary of Contents for AXIOMTEK TEN100 Series
- Page 1 TEN100 Series Hardened Unmanaged 8-port Fast Ethernet Switch User’s Manual Preface...
-
Page 2: Disclaimers
Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd. -
Page 3: Table Of Contents
Table of Contents Disclaimers ..........................ii Section 1 Preface ............ 1 Section 2 Block Diagram ......... 3 Section 3 Dimensions ..........4 Section 4 Product Overview ........5 Industrial Ethernet Switch ..................... 5 Package Contents ......................5 Product Highlights......................6 4.3.1 Basic Features .................... - Page 4 This page is intentionally left blank.
-
Page 5: Preface
TEN100-0800-H Series User’s Manual Section 1 Preface A member of the growing family of rugged switches, this switch addresses a need for a smaller switch. This switch provides an affordable solution for rugged and outdoor environment, transportation road-side cabinet, industrial floor shop, multitenant dwellings or Fiber To The Home (FTTH) applications. - Page 6 TEN100-0800-H Series User’s Manual This page is intentionally left blank. Preface...
-
Page 7: Block Diagram
TEN100-0800-H Series User’s Manual Section 2 Block Diagram Block Diagram... -
Page 8: Dimensions
TEN100-0800-H Series User’s Manual Section 3 Dimensions Dimensions... -
Page 9: Product Overview
TEN100-0800-H Series User’s Manual Section 4 Product Overview Industrial Ethernet Switch Package Contents When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller. -
Page 10: Product Highlights
TEN100-0800-H Series User’s Manual Product Highlights 4.3.1 Basic Features Complies with EN61000-6-2 & EN61000-6-4 EMC Generic standard immunity for ⚫ industrial environment. Supports IEEE802.3az 10Base-Te and 10Base-T. 10Base-Te is fully interoperable ⚫ with 10Base-T over 100m of class D (Category 5) or better cabling as specified in ISO/IEC 11801:1995. -
Page 11: Front Panel Display
TEN100-0800-H Series User’s Manual Front Panel Display 4.4.1 Power Status (PWR) This LED comes on when the switch is properly connected to power and turned on. 4.4.2 Port Status LEDs The LEDs display status for each respective port. Color Status LED On: Link Green LED Off: No Link... -
Page 12: Physical Ports
TEN100-0800-H Series User’s Manual Physical Ports This switch provides: Eight 10/100Base-TX ports ⚫ Connectivity RJ-45 connectors ⚫ Product Overview... -
Page 13: Installation
TEN100-0800-H Series User’s Manual Section 5 Installation This chapter gives step-by-step instructions about how to install the switch: Selecting a Site for the Switch As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. -
Page 14: Assembly, Startup, And Dismantling
TEN100-0800-H Series User’s Manual 5.2.1 Assembly, Startup, and Dismantling Assembly: Place the Switch on the DIN rail from above using the slot. Push the front of the ⚫ Switch toward the mounting surface until it audibly snaps into place. Startup: Connect the supply voltage to start up the device via the terminal block. ⚫... -
Page 15: Connecting To Your Network
TEN100-0800-H Series User’s Manual Relay Output Alarm The switch provides a relay output contact. The relay is for signaling of a user- defined power redundancy failure. The current is 0.5A@30VDC at Normal Open or Normal Close. POWER1 POWER2 RELAY contact INPUT INPUT Open, Start alarm... -
Page 16: Cabling
TEN100-0800-H Series User’s Manual 5.4.2 Cabling Step 1: First, ensure the power of the switch and end devices are turned off. <Note> Always ensure that the power is off before any installation. Step 2: Prepare cable with corresponding connectors for each type of port in use. <Note>... -
Page 17: Specifications
TEN100-0800-H Series User’s Manual Section 6 Specifications Industrial Ethernet 10/100Base-TX auto-negotiating ports with RJ-45 connectors Switch Applicable IEEE 802.3u 100Base-TX/FX Standards IEEE 802.3x Full-duplex Flow Control IEEE802.3az Energy Efficient Ethernet IEEE 802.1p Quality of Series (QoS) Forwarding Rate 10 / 20Mbps half / full-duplex 10Base-Te: 100 / 200Mbps half / full-duplex 100Base-TX:... - Page 18 TEN100-0800-H Series User’s Manual This page is intentionally left blank. Specifications...
-
Page 19: Appendix A Connector Pinouts
TEN100-0800-H Series User’s Manual Appendix A Connector Pinouts Pin arrangement of RJ-45 connectors: RJ-45 Connector and Cable Pins The following table lists the pinout of 10/100Base-TX ports. Regular Ports Uplink port Output Transmit Data + Input Receive Data + Output Transmit Data - Input Receive Data - Input Receive Data + Output Transmit Data + Input Receive Data -... - Page 20 TEN100-0800-H Series User’s Manual This page is intentionally left blank. Connector Pinouts...
Need help?
Do you have a question about the TEN100 Series and is the answer not in the manual?
Questions and answers