Summary of Contents for Austlift 145080
- Page 1 Lifting and Material Handling Specialist USER MANUAL AUSSIE FETCH MINI CRANE Code: 145080 1300 100 130 www.austlift.com.au AUSTLIFT PTY LTD AS/NZS 1418...
-
Page 2: Table Of Contents
AUSTLIFT AUSSIE FETCH MINI CRANE CONTENTS INTRODUCTION TECHINCAL SPECIFICATIONS STANDARD DIMENSIONS INSTALLATION • PACKAGING • MOUTING • STRUCTURE CHARACTERISTICS • ELECTRICAL INSTALLATION • CRANE INSTALLATION TYPE • LIFTING BELT INSTALLATION • TESTING SAFETY • BEFORE USE • LIFTING CHEMICAL OR FIRE HAZARD PRODUCTS •... -
Page 3: Introduction
Aussie Fetch is designed for light vehicles, light duty workshops or building site as handy lifting device. It can be installed in Austlift workshop, by our authorized dealer or by yourself if you have sound mechanical knowledge, with welding and fitting skills. (Video instruction soon will be available on... -
Page 4: Standard Dimensions
AUSTLIFT AUSSIE FETCH MINI CRANE STANDARD DIMENSIONS Unit: mm AUSSIE FETCH USER MANUAL... -
Page 5: Installation
AUSTLIFT AUSSIE FETCH MINI CRANE INSTALLATION Packaging When you open the box, the following parts are in the package. Indication image Description Qty. Crane Body Installation bolts, nuts 4 of and spacers each Installation Plate Instruction Manual and Certificate Hand Control with... -
Page 6: Structure Characteristics
AUSTLIFT AUSSIE FETCH MINI CRANE Indication of mounting on the rear of the vehicle Structure Characteristics The crane consists of following major parts: Main column, supporting rack, lifting arm, extension, electrical winch(12vDC) and removeable hand control. There are two ball bearings are in the main column for swing. -
Page 7: Electrical Installation
AUSTLIFT AUSSIE FETCH MINI CRANE Electrical Installation The crane comes with a 3M electrical cable wire. Red one is positive terminal. Black one is negative terminal. Connect the red and black wire with the respective positive and negative terminal of the 12V battery. Plug the pedant cable on the winch control box and then use the up/down buttons to operate the crane motor. -
Page 8: Lifting Belt Installation
AUSTLIFT AUSSIE FETCH MINI CRANE Lifting Belt Installation Inserting the belt at installation or replacing it with a new belt ensure the end is over the bolt, remount collar, press it together and secure bolts. See image below. Lifting webbing in the arm should pass over the pins, not under the pins. See image below. -
Page 9: Safety
AUSTLIFT AUSSIE FETCH MINI CRANE SAFETY Before Use Check the load weight, never overload. Crane is not for under 16 years old person to operate. Read the instruction carefully; to understand the structure and how to operate the crane. Check the power source to make sure it’s 12 V DC before turning power-on. -
Page 10: Lifting Chemical Or Fire Hazard Products
Check electrical cables and lifting belt for any cracks, tears, chemical or • physical damage, if any damage is found stop use immediately. Contact an Austlift authorized distributor for service and repair. Never route electrical cables: • - Across any sharp edges;... -
Page 11: Troubleshotting
AUSTLIFT AUSSIE FETCH MINI CRANE TROUBLESHOTTING SYMPTOM POSSIBLE CAUSES SUGGESTED ACTIONS Winch Motor will not • Switch inoperative • Replace switch operate, or runs in one • Broken wires or bad • Check poor direction only connection connections • Defective motor •... -
Page 12: Service Record
AUSTLIFT AUSSIE FETCH MINI CRANE SERVICE RECORD DATE COMMENTS/DEFECTS SIGNATURE AUSSIE FETCH USER MANUAL... - Page 13 AUSTLIFT AUSSIE FETCH MINI CRANE LIFTING AND MATERIAL HANDLING SPECIALIST AUSTLIFT PTY LTD 1300 100 130 www.austlift.com.au 43 Frank Street Wetherill Park, NSW 2164 Ph : 02 9757 2277 Copyright Austlift Pty Ltd Specifications and dimensions subject to change without notice.
Need help?
Do you have a question about the 145080 and is the answer not in the manual?
Questions and answers