Related Manuals for Silhouette Infinity 8161
Summary of Contents for Silhouette Infinity 8161
- Page 1 SUN Collection 2018 | Technical Information Mod. 8161, 8695, 8696 Infinity Collection Mod. 8158, 8697, 8698 TMA Icon Mod. 8162, 8163 TMA Atwire Mod. 8693, 8694 Titan Breeze Mod. 3191, 4075 Urban Sun...
- Page 2 RX technical information...
- Page 3 Rimless Glazing Information OMA shape files and drill charts are available at www.silhouettelab.com Patterns are available from Silhouette customer service at 800-223-0180...
- Page 4 Rimless Glazing Information Mod. sunlens opt. sunlens 8142 58 x 48 21° 8667 62 x 51 21° 8686 61 x 43 23° 8685 54 x49 16° 8690 47 x39 14° 8155 49 x43 16° 8154 64 x50 13° 8156 61 x50 11°...
- Page 5 Rimless Glazing Information Mod. sunlens opt. sunlens 8698 63 x45 19° 8158 60 x50 16° 8162 59 x49 16° 8163 58 x50 16° 8161 48 x42 12° 8695 49 x44 13° 8696 50 x42 13° 8693 55 x45 9° 8694 52 x47 9°...
- Page 6 Rimless Glazing Information...
- Page 7 Nylor Glazing Fullrim...
- Page 8 Inline Glazing Fullrim Lens in Lens...
- Page 9 Inline Glazing Fullrim Titanium...
- Page 10 Inline Glazing Fullrim SPX...
- Page 11 Nylor Glazing 0,70mm...
- Page 12 PRESCRIPTION WRAP LENS ORDERING Order wrap compensated free form lenses to match frame curve for all Silhouette • Sun Frames We recommend high index 1.60, 1.67, polycarbonate and Trivex • For aesthetic reasons, please consider finished lens edge thickness, especially with •...
- Page 13 Technical information per model...
- Page 14 TMA Icon (RL) / Cat Eye 8154...
- Page 15 Glazing | TMA Icon (RL) Cat Eye • No prescription glazing possible due to lens size and hole in the lens • Exchanging plano sun lenses is not a problem using Silhouette plier with purple tip and BLS 58...
- Page 16 Inclination | TMA Icon (RL) Cat Eye Inclination: hold the glasses with a plier and bend the temple in the requested direction...
- Page 17 TMA Ultra Thin (RL) 8697, 8698...
- Page 18 Glazing | TMA Ultra Thin (RL) No RX glazing due to 9.0 base curve and possible lens thickness Exchanging of plano sun lenses is not a problem using Silhouette plier with blue tip and BLS 58...
- Page 19 Inclination | TMA Ultra Thin (RL) Inclination: hold the glasses with a plier and bend the temple in the requested direction...
- Page 20 Adventurer Aviator (RL) 8142, 8667...
- Page 21 Glazing I Adventurer Aviator (RL) Rx with 8 base curve lens. Mount using Silhouette plier with blue tip and BLS 58/98/97 depending on thickness For browbar, use single hole Silhouette yellow plier tips and BLS 44 single hole...
- Page 22 INCLINATION and ADJUSTMENT Inclination: Hold lens fixation firmly. Temple opening: Hold lens fixation Hold temple firmly in the area of the firmly. hinge and inclinate it gradually by Adjust temple opening angle by hand hand. in the area of the hinge.
- Page 23 Adventurer Nylor 8685...
- Page 24 INCLINATION and TEMPLE OPENING Hold eye rim firmly in the area of Adjust temple opening by pressure on the side parts. the Snap-hinge and in small steps by Fix temple in the hinge area and hand. incline it by hand in small steps.
- Page 25 TEMPLE DISASSEMBLY Support eye rim firmly in the Place forefinger and thumb Temple will come loose with area of the side parts. left and right of the hinge and a click. After this thread out Fold temple by 45°. press temple by turning.
- Page 26 TEMPLE ASSEMBLY 1. Temple-end shows upwards. Press temple into the Snap-Hinge. 2. Insert temple into hook and turn it by180°. NOTE: Clean the hinge before assembling the temple and cover it with Teflon Precision Lubricant (P 0030) on the inside curve of the hook.
- Page 27 Carbon T1 - 8686...
- Page 28 Glazing I Carbon T1 (RL) • Glaze with 8 base Rx lens • Use Silhouette plier with blue tip and BLS 58/98/97...
- Page 29 Inclination Hold lens fixation in position Enclose temple edge firmly and with mounting pliers. adjust inclination on titanium side part into requested direction. Open temple completely.
- Page 30 Adjust Temple Opening Reduce Enlarge...
- Page 31 Temple Disassembly 1. Place disassembly tool at hinge 2. Close temple and press it using multi tool as to the stop. Select diameter of a fulcrum rounded part according to 3. Temple will loosen with a “click“. distance between temple and lens.
- Page 32 Temple Assembly 1. Place metal hinge exactly at 2. Apply counter pressure on frame openings of SPX-temple. side part. 3. Press SPX-temple into titanium side part.
- Page 33 Explorer Line 8690, 8155...
- Page 34 RX Glazing Inline|Explorer Line Use 6.0 base curve lenses for Rx glazing • Lenses with flatter base curve should have 5.0 base • curve groove cut into lens edge Sleeves are replaceable using Silhouette plier with • purple tip and BLS 58...
- Page 35 Inclination of Disc Hinge Support lens mounting with plier and adjust inclination with the white tool from the mounting box...
- Page 36 Exchange Disc Hinge & Temple Press the disc halves into While supporting lens While supporting lens the hinge and gently mounting, press mounting, pull temple squeeze with a plier temple on to hinge backward from disc disc...
- Page 37 The Infinity Collection 8161, 8695, 8696...
- Page 38 RX Glazing Inline| The Infinity Collection Use 6.0 base curve lenses for Rx glazing • Lenses with flatter base curve should have 5.0 • base curve groove cut into lens edge Sleeves are replaceable using Silhouette plier with • purple tip and BLS 58...
- Page 39 Inclination | The Infinity Collection Inclination: hold the chassis mounting with a plier and bend the temple in the required direction...
- Page 40 Temple Disassembly | The Infinity Collection 1. Hold lens mounting firmly with your fingers 2. With the other hand grasp the partially closed temple directly behind the hinge and push it in the direction of the lens 3. Turn the temple 180°to the front and slide it off the end piece.
- Page 41 Temple Assembly | The Infinity Collection 1. Hold lens mounting firmly with your fingers 2. With temple upside down insert the front hole of the temple hinge onto the end piece. 3. Slide the temple all the way onto the end piece so it is next to the lens. 4.
- Page 42 Dynamics Colorwave (8693, 8694)
- Page 43 Dynamics Colorwave | Special groove width...
- Page 44 Dynamics Colorwave | Enclosed Rubber Ring Place the enclosed rubber ring into the groove of the lens...
- Page 45 Dynamics Colorwave | Insert the Lens 1. Insert the lens from the rear, starting from the nasal corner to the temporal corner. 2. Continue pulling the lower titanium rim around the lens edge.
- Page 46 Dynamics Colorwave | Remove the Lens 1. Thread the Silhouette thread between the lens and frame at the temporal gap and slide it to the lower edge of the frame. 2. Separate the lower Titanium edge with the Silhouette thread and remove the...
- Page 47 Dynamics Colorwave | Inclination 1. Open the temple. 2. Hold the frame by the end piece with double padded pliers. 3. Incline the temple at the hinge.
- Page 48 Dynamics Colorwave | Temple Opening Enlarge 1. Ideally, remove the lens 2. Open the temple 3. Hold the frame by the end piece with your padded pliers 4. Press the temple outward with your thumb...
- Page 49 Dynamics Colorwave | Temple Opening Reduce 1. Ideally, remove the lens 2. Open the temple. 3. Hold the frame by the end piece with padded pliers 4. Press the temple inward with your thumb...
- Page 50 Dynamics Colorwave | Temple Contouring Use large curves to adjust the temple to fit the head...
- Page 51 Dynamics Colorwave | Temple end Adjustment Adjust the temple to the ear shape with large curves. During temple- end adjusting do not put pressure on the temple tip.
- Page 52 Dynamics Colorwave | Temple Removal 1. Hold the frame by the hinge area firmly with your fingers. 2. With the other hand grasp the partially closed temple directly behind the hinge and push it in the direction of the lens 3.
- Page 53 Dynamics Colorwave | Temple Mounting 1. Hold lens mounting firmly with your fingers. With temple upside down insert the front hole of the temple hinge onto the end piece. 2. Slide the temple all the way onto the end piece so it is next to the lens. 3.
- Page 54 Urban Sun 3191, 4075...
- Page 55 Urban Sun | Glazing Attention: Do not heat frame for lens insertion. Lenses must be resized if too large! 1.Insert lens from 2.First insert behind! whole side of Note: mounting from the lens on upper front could cause cracking edge of frame 3.
- Page 56 Urban Sun | Inclination Hold front frame firmly by hand in area of side part Cover temple edge closely and adjust inclination at titanium side part...
- Page 57 Urban Sun | Temple Removal Close temple Pull temple hinge out of SPX-front...
- Page 58 Urban Sun | Temple Mounting Place hinge into slot in front Press temple edge softly into SPX-front...
- Page 59 Urban Sun | Temple Adjustment Adjust temple curving in large movements Metal core inside temple enables cold adjustment...
- Page 60 Urban Sun | Model 4075 A rubber ring is enclosed with each frame which must be inserted in the groove of the lens This prevents twisting of the lens. Especially effective with round lens shapes Spare Part Number: P00009900250300...
- Page 61 TMA Atwire 8162, 8163...
- Page 62 Glazing | TMA Atwire Non Rx style due to lens size and multiple holes No pattern, OMA file or drill charts available Plano sun lenses can be exchanged using Silhouette plier with purple tip and BLS 44...
- Page 63 TMA Atwire | Glazing Affix protective film around BLS to protect the lens.
- Page 64 TMA Atwire | Glazing with replacement planos Carefully clip off the BLS head, but without damaging the 2mm long fixation pins. First remove the glass accessoir...
- Page 65 TMA Atwire | Glazing with replacement planos Secondly remove the temple and the bridge.
- Page 66 TMA Atwire | Glazing glazing with replacement planos Carefully remove remains of plastic from the fixation pins. NOTE: Fixation pins, barbed hooks, surfaces must NOT be damaged! Cuttings and grooves could cause breakages!
- Page 67 TMA Atwire | Glazing with replacement planos Insert BLS from the back and cut them with the BSL – Cutter...
- Page 68 TMA Atwire | Glazing with replacement planos Always mount the lens accessory first.
- Page 69 TMA Atwire | Glazing with replacement planos Cut the nasal BLS with an scalpel or when it is possible with the BLS - Cutter...
- Page 70 TMA Atwire | Glazing with replacement planos NOTE: Always support the mountings from above to prevent lens damage!