Table of Contents
Advertisement
sponding to the tape deck in use to monitor the just-recorded signal.
lf the input selector
is in any other position, another audio source
can be heard while recording is in progress. Set the proper recording
level using the controls on the tape deck.
The effects of the contra
bass, bass, treble, and balance controls cannot be heard during
recording.
Recording from a Video Source to a Tape Deck
1. vv the Recording source selector
of the tape recorder to
VI.
2. Select the video mode switch
to either the VCR [V] or VDP
[V], depending on your video source.
3. Start the tape deck to record.
4. Start the program source.
You can record from a video source and another source at the same
time by, for example, setting TAPE-1
to
and TAPE-2 to another
source.
Recording from an Audio Source to a Video Tape Recorder
1. Set the video mode switch
to VCR REC-SOUND.
2. Set the TAPE-2 recording source selector
to the source
you want to record.
4. Start the video tape recorder to record.
3. Start the program source.
You can record from TAPE-1
to a video tape recorder by changing
the TAPE-2 switch to DUB 1 P 2.
NOTE:
1. If the TAPE-2 switch is set to
or OFF, recording is not
possible.
2. Recording cannot be done from TAPE-2 to a video tape
recorder.
Tape-to-Tape
Duplicating
When two tape decks are connected at once to this unit, a tape
can be copied from one deck to the other. To copy a pre-recorded
tape from tape deck 1 (the deck connected to the rear panel TAPE-1
terminals) to tape deck 2 (connected to the TAPE-2 terminals),
perform the following procedure.
1. Place the TAPE-2 recording source selector
in the DUB 1
> 2 position and put tape deck 1 in the playback mode and tape
deck 2 in the recording mode. If tape deck 2 is a 3-head deck,
the just-recorded signal can be monitored by depressing the
TAPE-2 selector switch [8]. To monitor the signal from tape
deck 1 before it has been recorded, depress the TAPE-1 selector
switch
[a]. Depress one of the other input selector switches
to listen to the CD player, turntable, tuner or auxiliary
component while dubbing is taking place.
2. To copy from tape deck 2 to tape deck 1:
Place the TAPE-1
recording source selector
in the DUB 2
> 1 position and put tape deck 1 in the recording mode and
tape deck 2 in the playback mode. If tape deck 1 is a 3-head
deck, the just-recorded signal can be monitored by depressing
the TAPE-1 selector switch [8].
NOTE:
When the TAPE-1
recording source selector is set to DUB 2 >
1 and the TAPE-2 recording source selector is set to DUB 1 >
2, dubbing is possible only from tape deck 1.
VDP
to VCR
Recording
1. Select the VCR
REC-VDP position on the Video Mode switch.
2. Start the VCR unit, in the REC mode, connected to the VCR
terminals.
3. Then start recording by activating the video component con-
nected to the VDP terminals.
®
To monitor the video program being recorded, on the monitor
TV set, press the VCR or VDP switch of the Input Selector.
If
you want to listen to an audio program while recording a video
program, select the desired source by simply pressing the cor-
responding source switch of the Input Selector.
BGV PLAYBACK
(Background Video)
With this unit, you can playback programs on a monitor from a video
component connected to the VDP or VCR terminals while playing
your turntable, tuner, CD, tape decks.
In this example, you can playback a video program on a monitor
by selecting VDP-|V]
or VCR-[Vj
the Video Mode switch
while
listening to the CD player.
First, select the desired audio component with the Input Selector
[a]. Next, select the desired video component by adjusting the Video
Mode switch
to either the VDP [V] or VCR [VJ position.
NOTES:
@
When the Video Mode switch is set on VCR
REC-VDP-
VCR-[V], the video signal from the VCR is sent to the monitor
regardiess of the Input Selector switch position {3}, therefore
the playback signal of VCR is not interrupt even if the Input
Selector
switch
is turned to the VDP position.
lf there is no display from the VDP on the monitor in these
positions, be sure that both input and output leads are cor-
rectly connected between the video components and am-
plifier, all components are turned power on and the VCR
is
not playback mode. More importantly, make sure that your
VCR is capable of sending out a input signal.
Using a Mixing
Console or Graphic
Equalizer
A mixing console or graphic equalizer can be connected to the
TAPE-1
(or TAPE-2) terminals as shown in the diagram. Theinput
selector is then set to the TAPE-1
(or 2) setting, depending on the
terminals to which the mixing console or equalizer is connected
and the recording source selector to the program source to be used
with mixing
or equalization.
Audio mixer or
Integrated amp
graphic equalizer
Sa
Soe
awe TRULIA TTT
We
om
oe
-
te
ele
O-Geee.
«=
Co
G
——
OCLC,
To Equalize an Audio Source for Playback
1. Press the TAPE-1
switch of the !nput Selector.
2. Select a program source to be equalized on the TAPE-1
REC
selector
(for example, the CD player).
3. To equalize the audio signal of a video component connected
to the VCR or VDP terminals, select the [V] position on tle
TAPE-1 REC selector
and the VCR-|V]
or VDP- {VJ position
on the Video Mode switch [17].
To Record
an Equalized
Program onto a Tape Deck
Com-
nected to the Tape-2 Terminals
1. Select the DUB
1 > 2 position on the TAPE-2
REC selecor
18}.
2. Select a program source to be equalized and recorded viat fhe
TAPE-1
REC selector {18}.
3. To record the equalized audio signal of a video componat
connected to the VCR or VDP terminals, select the
Posi tion
on the TAPE-1 REC selector
and the VCR-[V] or
VDP-[V] position on the Video Mode switch [17].
To Record
an Equalized
Program onto a VCR
Connected
to the VCR
Terminals
1. Select the SOUND
REC position on the Video Mode swich
iar
2. Select the DUB
1
2 position on the TAPE-2
REC seletor
18}.
3. Select a program source to be equalized and recorded viit he
TAPE-1
REC selector.
NOTE:
Equalized audio dubbing cannot be done directly from thea pe
deck 2 to the VCR.
An equalized signal first has to be roueed
through other audio source circuitry.
Therefore, connect tle
output leads of the tape deck to the input terminals of an acdio
source, such as tuner.
Advertisement
Table of Contents
