Advertisement
5.9.
When the heater is not in use for any length of time, disconnect it from the electrical and gas supply and store it in a safe, dry, childproof
location.
WARNING! If the flame shuts down during operation, before repeating the ignition sequence, make sure that the fan is not jammed, and
‰
the air inlet and outlet are completely free of obstructions. If it is due to overheating, the cause of the problem must be determined and
corrected before repeating the ignition procedure.
6. MAINTENANCE
WARNING Before commencing service or maintenance, disconnect the heater from the electrical and gas supplies and allow to cool fully.
‰
Use authorised parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Should the heater require service or maintenance, a suitably qualified engineer should carry this out or contact your local Sealey service
agent.
6.1.
Check the gas supply hose condition regularly, change if necessary.
Clean the heater with a damp cloth, DO NOT use abrasive or solvent or abrasive cleaners.
6.2.
WARNING: AIR CONTAMINANTS
‰
Air contaminants taken into the heater will damage the unit, cause health problems and safety issues.
For example: Body shop filler dust and overspray dust will clog the burner diffuser, contaminate the combustion chamber and
damage the internal parts of the heater. If contaminants are present the heater must be supplied with ducted clean air.
Please note that any parts damaged by filler dust or overspray dust will not be covered by warranty. Additionally a cleaning
charge will be made for any heaters damaged by filler dust or overspray dust.
7. TROUBLESHOOTING
PROBLEM
Fan motor does not work.
Ignitor does not spark.
No gas flow to the burner.
.
The burner starts, but stops as
the gas control knob is released.
The heater stops during operation
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
.
POSSIBLE CAUSE
1. There is no electrical supply.
2. The motor has locked.
3. Fan blades bent or in contact with
housing.
1. Electrode has the wrong gap.
2. Faulty connection.
3. Corroded electrode.
1. The cylinder gas tap is closed.
2. The cylinder is empty.
3. Gas leaks from the supply.
1. The thermocouple is not warm enough.
2. The safety override has activated
because the fan does not work.
1. Excessive gas supply.
2. Insufficient gas due to ice formation
on the cylinder.
3. Temperature inside heater is too high.
4. Dust or debris accumulated in heater.
sales@sealey.co.uk
Original Language Version
SOLUTION
1. Check mains power supply, wire, plug, fuse.
2. Unlock the motor with an appropriate tool.
3. Check housing for damage, straighten blades.
1. Check and reset the electrode gap to 4mm.
2. Inspect and connect correctly the ignitor and the electrode.
3. Replace ignition electrode.
1. Open the gas tap.
2. Replace with a full cylinder.
3. Remove and clean the nozzle, check for leaks by using a
foamy soap only - DO NOT USE FLAME to find leak.
1. Repeat the ignition sequence, keeping the control knob
pushed in for a longer time.
2. See above - Fan motor does not work.
1. Check the pressure regulator, replace if necessary.
2. Check and if necessary use a larger gas cylinder or multiple
cylinders connected in parallel.
3. Keep area around heater inlet clear of obstructions.
4. Clean inside of heater.
www.sealey.co.uk
LP41.V2, LP55.V2
REGISTER YOUR
PURCHASE HERE
Issue: 3 (2)
18/04/23
Advertisement
