Advertisement
Quick Links
Barbarian Basketball Systems Inc.
Titanium Series
ADJUSTABLE BASKETBALL SYSTEM
ASSEMBLY INSTRUCTIONS AND OWNER'S MANUAL
Model - FC-6x60
& FC-6x72
!
WARNING
FAILURE TO COMPLY WITH ANY OF
THE WARNINGS IN THESE INSTRUCTIONS
MAY RESULT IN SERIOUS PERSONAL
INJURY.
FAILURE TO COMPLY MAY ALSO
RESULT IN PROPERTY DAMAGE.
PLEASE HEED ALL WARNINGS AND
CAUTIONS TO ENSURE YOUR SAFETY.
DO NOT ATTEMPT TO ASSEMBLE
THIS SYSTEM WITHOUT CAREFULLY
READING AND FOLLOWING ALL
INSTRUCTIONS. BEGIN BY IDENTIFYING
AND TAKING INVENTORY OF ALL PARTS
USING THE PARTS LIST PROVIDED.
Keep this instruction manual in case you have to contact the manufacturer for replacement parts.
!
1
Advertisement
Related Manuals for Barbarian Basketball Systems FC-6x60
Summary of Contents for Barbarian Basketball Systems FC-6x60
- Page 1 Barbarian Basketball Systems Inc. Titanium Series ADJUSTABLE BASKETBALL SYSTEM ASSEMBLY INSTRUCTIONS AND OWNER'S MANUAL Model - FC-6x60 & FC-6x72 WARNING FAILURE TO COMPLY WITH ANY OF THE WARNINGS IN THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY. FAILURE TO COMPLY MAY ALSO RESULT IN PROPERTY DAMAGE.
- Page 2 TOOLS AND MATERIALS REQUIRED FOR ASSEMBLY (Not Included) 1. 2 Adjustable Wrenches 10. Concrete-1/2 yard or 14-16 2. Socket Set Bags, (80 lb. bags) 3. 9/16" Wrench 11. Phillips Head Screwdriver 4. 3/4" Wrench 12. A minimum of 2 Ladders 5.
- Page 3 Verify all parts listed on packing list are present prior to installation. Contact our Customer Service at 620-662-2233 for assistance with replacement of any parts missing or damaged. 13 10 10 13 PARTS LIST ITEM QTY DESCRIPTION 6"x6"Main Post Actuator Spring-Assist Cartridge Pole and gusset padding Rim Height Sticker...
- Page 4 NOTE: Before digging, call to locate any buried utility lines. ’ NOTE: At rim height 10 , distance from the face of backboard to the ” front of Main Post(A) is 48 , Choose the proper location to dig for the concrete footing: STEP A a.
- Page 5 STEP C a. Mix the concrete according to the instructions on the bags. Note that a thicker mix of concrete will dry stronger than a thin mix. Pour the concrete into the hole, stopping approximately 18 inches from the top of the hole.
- Page 6 WARNING *BECAUSE OF THE SIZE AND WEIGHT OF THE SYSTEM, A MINIMUM OF THREE ADULTS ARE REQUIRED FOR THE FOLLOWING STEPS* STEP1 Slide a 18mm Thick Washer (U3) over each of the J-Bolts (U2) as shown in FIGURE 1A. Remove the Padding from Main Post (A). Place the Main Post (A) over the J-Bolts. Slide a 18mm Thick Washer (U3), a Lock washer 18mm (U6) and thread a 18mm Hex Nut (U4) to each J-bolt.
- Page 7 STEP 3 Connect Actuator to Main Extension arm. Place the upper bracket of Actuator(B) between the last set of welded tubes on the Main Extension Arm (F), attach the two parts using Hex bolt M18X320mm (#5), two Flat Washers M18 (#11), one Lock nut (#14). Connect Actuator(B) to the mounting bracket welded in the middle of Post (A), using one Hex Bolt M16x135mm (#9), two flat Washers for M16 Bolt (#12),...
- Page 8 STEP 6 Crank the Main extension arm as low as possible. 13 10 Attach the Backboard to Main Extension Arm (F) by using a Hex Bolt m16x320mm (#7), two M16 Flat Washers(#12), two Nylon washers (#2) and one Lock Nut M16 (#15).