Advertisement
D. Privacy Number
The "Privacy Number" is factory disabled so an entry phone off-hook will automatically ring the house phones. If a
"Privacy Number" is programmed, the visitor must Touch Tone dial the number to be able to call into the house. The
"Privacy Number" may be from 1 to 6 digits and is stored in location "#00". To disable the "Privacy Number," clear the
number's memory location by entering "#00" without any previous digits.
E. Entry Codes
Each entry phone may have its own entry code for Touch Tone keyless entry. The entry codes may be from 1 to 6 dig-
its and are stored in locations "#11" through "#14" for entry phones 1 through 4 respectively. A master entry code can
be used at any entry phone and is stored in location "#50". To clear any entry codes, simply enter just the location num-
ber (ie. "#11") without any previous digits.
F. Relay Timers
A double pole double throw relay is available for each entry phone, and each may
be programmed with its own activation time, programmed in seconds. Each time
must be 2 digits (Example: 00 = 1/2 sec.) and is stored in locations "#21" through
"#24" for relays 1 through 4 respectively. The auxiliary contacts relay activation
time is stored in location "#30". All activation times are factory set to 00 (1/2 sec.)
Note: A short buzz will indicate when a relay has been activated.
G. Caller ID
The C-2000 is factory set to send "Caller ID" and "Call Waiting ID" information from the entry phones. If "Caller ID" is
not required, enter " 2" while in programming to disable the C-2000 from sending Caller ID data to the house phones.
Enter " 1" to enable Caller ID data.
H. Ring Cadence
Entry phone calls are factory set to ring the house phones in a standard ring cadence (2 seconds on/4 seconds off), "
4". The C-2000 can be programmed to give a double ring for entry phone calls (.7 seconds on/.3 seconds off/.7 sec-
onds on/4 seconds off), enter " 3" when in programming.
I. Dial Tone
1. C.O. Dial Tone (Factory Default)
To program the C-2000 for C.O. dial tone, enter " 5" while programming. To gain access to C.O. dial tone, dial a
Touch Tone "9".
2. Private Dial Tone
To program the C-2000 for private dial tone, enter " 6" while programming. House phones will instantly have dial
tone on an off-hook.
J. Maximum Ring Count
The number of times an entry phone call will ring the house phones can be limited in programming. The programma-
ble maximum ring count must be 2 digits and is stored in location "#40". The maximum ring count is programmable
from 1 - 99 and factory set to (05) 5 rings.
O
p
e
r
a
t
i
o
n
O
p
e
r
a
t
i
o
n
A. Visitors
When a visitor presses the call button (comes off hook), the entry phone will ring
down to the house phones and "Caller ID" information is sent. If a house phone is on
a C.O. call, call waiting tones and "Call Waiting ID" information is sent. A Touch Tone
"#" from the house phone will put the C.O. call on hold and the C-2000 will connect
to the entry phone and beep its location number. Enter Touch Tones "
tarily activate that relay and return to the C.O. call or enter "#" to just return to the
C.O. call. A 1/2 second buzz will indicate when a relay has been activated.
If you require the door strike to remain on continuously (ie: a truck delivery), enter Touch Tones " 1" to continuously
activate that relay and return to the C.O. call. A long buzz will indicate the door strike relay is latched on. When the
visitor calls in again (ie: they are finished unloading the truck), enter Touch Tones " 0" to deactivate the relay. A short
buzz will indicate the door strike relay is off.
B. Monitoring
Tenants may dial out to an entry phone that supports auto-answering capability by dialing "#1", "#2", "#3" or "#4" to call
entry phones 1-4 respectively. All recent Viking Handsfree Phones are equipped with an Auto-Answer feature.
Relays
Phones
1
2
3
4
Entry
Phone
1
2
" to momen-
3
4
Entry
Memory
Position
1
#21
2
#22
3
#23
4
#24
Caller ID and
Call Waiting ID
"Entry Phone 1"
"Entry Phone 2"
"Entry Phone 3"
"Entry Phone 4"
Advertisement
