WaveForm Ultrapole Quick Start Manual

Ultrapole: The Universal Antenna Mount
Run into any issues or have any suggestions? Call 1-800-761-3041, or email help@waveform.com
to get connected with our dedicated Waveform Signal Specialists. We'd love to hear from you.
Base Kit
• 1x J-Pole
A
1x Footpad
•
B
• 4x Bolts, Plastic Washers,
C
and Flange Nuts*
• 5x Expansion Bolts*
D
A B B
D
5 x
Where to Install the Universal Antenna Mount
Here are some suggestions on where to install the Universal Antenna
Mount:
1
Rooftop. When installing on a roof, make sure to properly seal any penetrations
made by screws. Consider using pitch pads, roofing sealant/caulking/cement, or
other weather proofing materials.
2
Wall / Siding / Fascia. Installing on the side of a building? Make sure the
footpad(s) are secured against a sturdy material. Damaged, rotted, or weakened
material may cause issues later on.
3
Pole / Railing. If your roof or siding isn't suitable, the Universal Antenna Mount
can be installed against a pole or railing. In such cases, hose-clamps or U-bolts are
recommended.
4
And many more! Don't let an instruction manual be the boss of you. You're
Leonardo da Vinci, and installing this mount is your Mona Lisa. It includes mounting
equipment to enable its installation at a variety of locations! It's called the Universal
Antenna Mount for a reason.
Assembling the Base Kit
Use the provided Size-8/10mm Wrench to assemble the Base kit. Follow the steps listed below:
1. Install Footpad
against a surface.
Questions? Suggestions? Need help? Call 1-800-761-3041, or email help@waveform.com
by
• 5x Wood Screws and
E
Anchors*
• 1x Size-8/10mm Wrench
F
4x Zip and Velcro Ties
•
G
*Includes 1x spare
C
4 x
E
5 x
F
G
4 x
2. Attach J-Pole with 3. Install adjustment
pivot Bolt. Bolt and adjust J-Pole
Extension Kit
• 1x Extension Pole
A
2x Brace Arms
•
B
• 2x Bolts, Plastic Washers,
C
and Flange Nuts*
• 5x Expansion Bolts*
D
A
B
2 x
E
5 x
G
Screw & Bolt Guide
To assemble the mount,
Washers, and Flange Nuts.
To install the mount against a surface,
Wood Screws, Anchors, and Expansion Bolts.
• For hard materials (e.g. concrete, brick mortar):
- Use the Wood Screws & Anchors.
- The Anchors require a pre-drilled 8mm hole.
• For semi-soft materials (e.g. wood):
- Use the Wood Screws.
• For soft materials, (e.g. plaster, drywall):
- Use the Expansion Bolts.
- The Expansion Bolts require a pre-drilled
12mm hole and PH2 Phillips-head screwdriver
(not included).
Tip:
Prior to drilling, place the footpad against the
intended mounting surface and mark the location of
each hole with a pencil or marker.
4. (Optional) Install lock
Bolt.
• 5x Wood Screws and
E
Anchors*
• 1x Size-8/10mm Wrench
F
1x Size-4mm Allen
•
G
Wrench
*Includes 1x spare
C
2 x
D
5 x
F
use the Bolts, Plastic
use the
5. Secure each Bolt
with a Washer and Nut.
waveform.com