Subscribe to Our Youtube Channel
Summary of Contents for FiT Bodywrap AVANT
- Page 1 AVANT™ FIT Bodywrap Professional Body Slimming System Installation and User Manual...
-
Page 2: Table Of Contents
Contents I. Foreword II. Working Principles III. Installation Instructions IV. System Control & Key Functions V. Operation Instruction VI. Cautions (please read carefully). VII. Troubleshooting Guide VIII. Technical Data... -
Page 3: Foreword
This system adopts first-class technology to intelligently and accurately control temperature and time. The system also implements low voltage for added safety. Therefore, FIT® Bodywrap is the system of choice at beauty salons and weight loss facilities across Europe and America. -
Page 4: Working Principles
This coat was specifically engineered to create yet another barrier and enhances the effects of both the FIT Booster and the far infrared heat from the FIT Bodywrap, and also to contain the majority of the sweat generated during a session. - Page 5 During a 15-minute sauna, your body can produce as much as 2 pints of sweat. Most active people have a normal sweat rate for an entire day of about 1 or 2 pints. During a FIT® Bodywrap you can actually sweat more than being in a sauna for 15 minutes.
-
Page 6: Installation Instructions
III. Installation Instructions 1. Determine Placement If using on a table top or cart, place Controller on a sturdy table that is easily · accessible. For wall mounting use provided guide included with Controller or secure optional · wall mount. It is recommended that the Controller be within arms reach of the customer during ·... - Page 7 2. Zone Connections Once Controller is in place, match numbered yellow tab on cable to corresponding · port on Controller. (See Fig.1) Line 6-pin connector using notch guide. (See Fig. 2,3) · Secure connection with plastic lock nut on cable. (See Fig. 4) ·...
- Page 8 This step only applies if mounting Controller on the wall.. · Use Cable Support Bracket to secure zone cables to the wall to protect from · damage. (See Fig. 9,10) Your FIT Bodywrap System is now ready for operation! · - 6 -...
- Page 9 Controller Operation: To power on your controller flip the green power switch located on the back of the · Controller. On the front panel of the controller use the “START/STOP” button to start a session. · Use the “Heating Zone” button, to switch between zones 1-4. ·...
- Page 10 power switch. If any of the cables or connecters show damage, please discontinue use · immediately. Do not pull on the cables. · Clean the inside of the wraps after every session to maintain cleanliness and · protect the inner surfaces. Do NOT place the Arm Wraps inside of or tucked under the Body Wrap during ·...
-
Page 11: System Control & Key Functions
IV. System Control & Key Functions AVANT™ Control Panel 1). Power LED: Turn on the power switch located on the back of the device. The power indicator light on the panel will illuminate. The device will be powered, but the session will not start yet (the body wrap will not be powered). -
Page 12: Operation Instruction
After choosing a zone, press the time UP or DOWN button to adjust the time for the session; the time for all zones are linked together. Each time the UP or DOWN button is pressed, it will increase or decrease in 5 minutes increments. The factory preset time when the device is turned on is always 45 minutes. - Page 13 FIT® Bodywrap Session Procedure: BEFORE A. Please remember to use the restroom prior to your FIT Bodywrap® session. B. Drink plenty of room temperature water, at least 16 oz. C. Disrobe completely and remove all jewelry. D. Apply FIT Booster™ spray generously, paying particular attention to any problem areas and put on this disposable FIT Coat™, both designed to amplify...
-
Page 14: Cautions (Please Read Carefully)
Maintenance can only be performed by the manufacturer or an authorized agent. • FIT® Bodywrap makes no therapeutic claims. Our product and the FIT604A system are not intended to diagnose, treat, cure, or prevent any disease or - 12 -... - Page 15 Please consult your physician before using any deep heating treatment such as FIT Bodywrap. • Those who suffer from health conditions, illness or disease, please consult your personal physician before using this device. • In case you feel unwell, dizzy, or tired during the session, please stop using immediately and consult a physician.
-
Page 16: Troubleshooting Guide
1) Controller must be repaired by 1) Internal error. on, and the green a qualified technician. Please main power switch reach out to FIT Bodywrap to on the back DOES schedule maintenance. light up. Green light on a That specific zone is Normal operation. - Page 17 Symptom Cause Solution Green light on That specific zone has Normal operation. All zones a specific zone reached the desired will continually change is BLINKING temperature and is states back and forth from (IDLE) temporarily on idle. solid to blinking throughout the whole session in order to control temperature Green light on...
-
Page 18: Technical Data
Please visit http://www.FITbodywrap.com for warranty information. VIII. Technical Data Model: AVANT (FIT604A) Input voltage: 1 10VAC-120VAC 12A 50/60Hz 200VAC-240VAC 7.5A 50/60Hz by internal switch Temperature setting: 85°F - 135°F Default session time: 45 minutes Time settings adjustment range: 5-95 minutes ... - Page 19 FIVE DIAMOND TRADING COMPANY, LLC 13100 KIRKHAM WAY. SUITE 202, POWAY, CA 92064 (760) 542 6707 • WWW.FITBODYWRAP.COM - 17 -...
Need help?
Do you have a question about the Bodywrap AVANT and is the answer not in the manual?
Questions and answers