Advertisement
Quick Links
Advertisement
Summary of Contents for Paragon Ah Caramba!
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS Paragon values your continued safety above all else. Please follow these guidelines when using your equipment to prevent injury and maximize product performance: WARNING No direct contact to equipment by the general public should be allowed when used in food service locations. Only trained personnel should operate this equipment. Carefully read any and all instructions before beginning operation of the equipment. Always wear safety glasses when servicing equipment. ... - Page 5 1. Make sure all machine switches are in the OFF position prior to plugging the equipment into an electrical receptacle. 2. Make sure the wall outlet can accept the grounded plus on the power supply. 3. The wall outlet must have the proper polarity. If in doubt, have a licensed electrician inspect the outlet and correct if necessary. 4. DO NOT use a ground to un‐grounded receptacle adapter. 5. Place the unit on a level surface. CLEANING Before using the unit for the first time, make sure unit is disassembled and cleaned properly. Please clean the product after each use. Stainless steel parts can corrode so it is important to properly clean, rinse, sanitize and dry all parts daily or after each use. Failure to comply with these instructions may result in a void warranty. BE AWARE BE AWARE OF THE PRODUCT YOU ARE DISPENSING AND ITS TEMPERATURE MAINTAINING REQUIREMENTS. Paragon International will not be responsible for dispensing of potentially hazardous product. ...
-
Page 6: Controls And Their Functions
OPERATING INSTRUCTIONS CONTROLS AND THEIR FUNCTIONS Orange Button – Factory set to dispense product for four (4) seconds Yellow Button – Factory set to dispense product manually 1. Plug the power cord into a grounded outlet and turn the warmer on. 2. Pre‐heat the unit with your cheese product inside for approximately one hour. See the next page for the installation of the cheese product. 3. Dispensing temperature is set at the factory to the optimal cheese heating setting of 140 °F ‐ 155°F/ 60°C ‐ 68°C. Note: It is normal for the cabinet’s temperature will vacillate between 140 °F ‐ 155°F/ 60°C ‐ 68°C during operation. CHEESE PRODUCT INSTALLATION Installing and Removing Cheese Food Product ... - Page 7 ...
- Page 8 REMOVAL OF THE TUBE AND PRODUCT POUCH 1. Open the door of the warming dispenser. 2. Open the tube clamp by rotating the cam counter‐clockwise. 3. Remove the tubing from the cam clamp by pulling from the bottom up. 4. Remove the empty product cheese bag and tube from the warming dispenser. WARNING: Always turn the POWER switch to OFF when the machine is not in use. INITIAL SET UP FOR PORTION AND TEMPERATURE CONTROL HOW TO CHANGE DISPENSING SETTINGS USING THE LCD DISPLAY AND CONTROLS The LCD Display and Controls has two primary functions: 1) it allows machine operator to view the temperature of the cabinet: 2) allows machine operator to toggle between Fahrenheit ( °F) and Celsius (°C), and it allows the machine operator to control dispensing portions of the front Orange Button. ...
-
Page 10: Care And Cleaning
Try another outlet Check outlet circuit breaker Door will not close Clamp open Close hose clamp Tray not fully in oven Push tray further into its slot Product is not Dispensing Tube isn't in slot Check/fix tube Clamp not closed Close clamp Out of product Open door ensure product available Product is leaking Clamp not closed Close hose clamp Tube loose from spout Tighten tube spout Tube not reaching bottom of clamp Spout not seated in receptacle Seat spout in receptacle ... - Page 11 3. Open the door and use a vacuum cleaner and a damp cloth to gently clean the air intake components. 4. Position the unit for normal operation and reconnect to the power supply. GENERAL SERVICE, REPAIR AND RETURNS Before returning any Paragon item, you must call the customer service department to receive return authorization. Failure to do this may result in reduced or no return credit. Customer service will provide instructions on how to ship the unit back. Paragon has a well‐qualified, highly‐skilled technical support staff. We value service and are always willing to help. The supply cord cannot be replaced and if the cord is damaged the appliance should be scrapped. PARAGON INTERNATIONAL, INC. WARRANTY Paragon International, Inc. (“Paragon”) warrants that, for a period of twelve (12) months from the date of purchase (the “Warranty Period”), the equipment manufactured will be free from defects in workmanship and material provided, if the machine is used in the manner and in the environment for which it was manufactured. Disclaimers and Limitations Other than as set forth above, Paragon specifically disclaims all express and implied warranties, including bit not limited to, warranties of merchantability and/or fitness for a particular purpose or use. This warranty does not extend to repairs or alterations undertaken without the prior written contest of Paragon of for goods that are misused, abused or neglected or if the goods are not properly stored, maintained, installed or operated. Paragon shall not be liable for incidental, special, indirect, exemplary, punitive or consequential damages resulting from the use of the goods or arising out of any breach of this warranty; including but not limited to damage to the property or loss of profits or revenue. Claims Administration All warranty claims must be made by calling Paragon Customer Service at 800.433.0333 during the Warranty period. If the unit is under Warranty, Paragon will send a new unit. Paragon may wish to have the defective unit returned to Paragon for review. Prior to calling, please have the date of purchase, serial number and model readily available. ...
Need help?
Do you have a question about the Ah Caramba! and is the answer not in the manual?
Questions and answers