Table of Contents
Advertisement
Quick Links
BANTAM BEAMER
ADJUSTABLE FROM 3.5 -14 inches
Model # A555000CE
WARNING:
ALL USERS OF THIS EQUIPMENT MUST READ AND
UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY
RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE
FAMILIAR WITH PERTINENT REGULATIONS GOVERNING THIS
EQUIPMENT. ALL USERS OF THIS PRODUCT MUST BE PROPERLY
INSTRUCTED ON HOW TO USE THE DEVICE. AVOID CONTACT
WITH PHYSICAL HAZARDS (THERMAL, CHEMICAL, ELECTRICAL,
ETC.). MAKE ONLY COMPATIBLE CONNECTIONS.
Patent US # 8,312,966 / US # 8,646,575 / US 8,973,705 B2
Advertisement
Table of Contents
Summary of Contents for zarges A555000CE
- Page 1 BANTAM BEAMER ADJUSTABLE FROM 3.5 -14 inches Model # A555000CE WARNING: ALL USERS OF THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE FAMILIAR WITH PERTINENT REGULATIONS GOVERNING THIS EQUIPMENT.
-
Page 2: Use Instructions
Read This Instruction Manual Carefully Before Using This Equipment. User Instructions must always be available to the user and are not to be removed except by the user of this equipment. For proper use, see supervisor, User Instructions, or contact the manufacturer. Werner Co. can supply additional information upon request. Compliant fall arrest and emergency rescue systems help prevent serious injury during fall arrest. -
Page 3: Component Materials
COMPATIBILITY LIMITATIONS Anchorage connector must only be coupled to compatible connectors. OSHA 29 CFR 1926.502, 1910.140, and EN 362 prohibits snaphooks from being engaged to certain objects unless two requirements are met: it must be a locking type snaphook, and it must be “designed for”... - Page 4 LOADING CONDITIONS DIAGRAM Placement at or below a user’s working height requires integration of an ANSI Z359 compliant energy absorbing connecting component (Energy Absorbing Lanyard or Self Retracting Lifeline) and free fall limits of the connecting component must be followed. The beam anchor must be attached to the I-beam flange facing the user (top flange if above, bottom flange if below, etc.).
-
Page 5: Warning Label Locations
WARNING LABEL LOCATIONS BREAKING STRENGTH: 5000 lbf (22.2 kN) MFG: MM/YYYY WARNING: All persons using this equipment must read, understand and follow all instructions. Failure to do so could result in serious injury or death. Compliance: OSHA 1926.502, OSHA 1910.140, ANSI Z359.18 Type A, ANSI Z359.7(19) EN 795:2012 Type B CE 0161 WARNING: ALL USERS OF THIS EQUIPMENT MUST READ AND... - Page 6 Annex II Regulation (EU) 795: 2012 2016/425 1.1.1. Ergonomics 3.1.3.Mechanical vibration 3.2.Protection against static compression of a part 1.1.2.1. Optimum level of protection of the body 1.1.2.2. Classes of protection appropriate to different 3.3.Protection against mechanical injuries levels of risk 1.2.1.1.Suitable constituent materials 3.4.1.Prevention of drowning 1.2.1.2.Satisfactory surface condition of all PPE...
-
Page 7: Maintenance, Cleaning And Storage
MAINTENANCE, CLEANING AND STORAGE Cleaning periodically will prolong the life and proper functioning of the product. The frequency of cleaning should be determined by inspection and by severity of the environment. Clean with compressed air and/or a stiff brush using plain water or a mild soap and water solution. Do not use any corrosive chemicals that could damage the product. - Page 8 Notified Body responsible for the EU type examination and ongoing conformity: AITEX Plaça Emili Sala, 1, 03801 Alcoi, Alicante, Spain, +34 965 54 22 00 Zarges Zargesstraße 7 82362 Weilheim, Germany +49 881 687 - 100 www.zarges.de 105548-11 REV J...