Further safety instructions for the battery pack 2.9.7 Service / Maintenance / Repair 2.10 Intended use 2.10.1 Uses 2.11 Reasonably foreseeable misuse Product Description Scope of supply | 2 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 3
Insert the battery pack 5.5.4 Remove the battery pack 5.5.5 Dust extraction Operation Safety Requirements Start the work process End the work process Cleaning Safety Cleaning work | 3 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 4
Maintenance Safety Maintenance work Disposal Service Warranty | 4 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
This instruction manual contains all important information necessary for safe handling of the cordless diamond wall chaser ABDN 20. Validity of the instruction manual This instruction manual is valid for the cordless diamond wall chaser ABDN 20. Storing the instruction manual Always store this instruction manual together with the machine.
End users Only persons over 16 years of age may use the machine. The operating personnel must be familiar with the content of this instruction manual. | 7 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Keep the connection cable away from heat, oil, sharp edges and moving machine parts. Damaged or kinked connection cables increase the risk of an electric shock. | 8 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Use the intended rechargeable batteries only in the power tools. Use of other rechargeable batteries can cause injuries and a risk of fire. | 10 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
The approved speed of the insert tool must be at least as high as the maximum speed given on the power tool. Accessories which rotate faster than approved can break and fly off the tool. | 11 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 12
Contact with a live conductor can also energise metal parts of the tool and cause an electric shock. | 12 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Prevent insert tools from rebounding from the workpiece and jamming. The rotating insert tool tends to get stuck in corners, sharp edges or if it rebounds. This causes loss of control or kickback. | 13 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
This power tool produces a large torque. If the power tool is not properly supported during use, the user can loose control of it and injuries can occur. | 14 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Vacuum the workplace to keep it clean. Sweeping or blowing swirls up dust. NOTE Observe the relevant regulations in your country for the materials to be machined. | 15 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Inhaling fine mineral and/or toxic dust can cause health hazards. We recommend wearing a face mask respirator with filter class P2 or P3 (to EN 149:2001). | 16 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Chapter 9, Disposal; Page 43). Before disposing of the power tool, discharge the battery pack in it. Secure the contacts against short-circuit (e.g. insulate with adhesive tape). | 18 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
The cordless diamond wall chaser ABDN 20 is only approved for making dry cuts in Poroton, bricks, calcium silicate, plaster and exposed aggregate concrete in conjunction with a special dust extractor.
Page 20
Do not machine the following materials: metal, wood, glass, etc. | 20 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
The machine is insulated in such a way that it has no exposed metal parts that could be live in the event of a fault. It does not have a protective earth conductor. | 21 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 22
Before starting any work with or on the machine, this instruction manual, the safety instructions and the warnings must be read through carefully and observed. | 22 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Slide switch for switching on / off 3.3.2 Safety devices The machine has a fixed protective hood with a rotatable socket for connection of a special dust extractor. | 23 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Furthermore, there is no need for scheduled replacement of the carbon brushes. In addition, our machines with brushless motors are compacter and lighter with the same power. | 24 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
The head of development is authorised to write the technical documents. These are available from: Maschinenfabrik OTTO BAIER GmbH Heckenwiesen 26 71679 Asperg Germany Thomas Schwab Robert Pichl Managing Director Factory Manager Asperg, 17/11/2021 | 27 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
The diamond grains become blunt and do not break out of the bond. The diamond discs no longer have any cutting power. Remedy: The material to be machined requires diamond discs with a softer bond. | 28 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Switch off the machine. Wait for the machine to completely stop. | 29 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 30
Check the fit of the diamond discs (6 / 7). The diamond discs (6 / 7) must be fitted as described above and must be able to freely rotate. | 30 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
(6 / 7) by hand until the spindle locking noticeably latches into position. Loosen the retaining screw (3) with the Allen key (2). | 31 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Note and follow the instructions on charging the battery pack given in the instruction manual of the BAIER quick charger ASC 145. | 32 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Press the battery pack release (3) to unlock the battery pack (2). Pull the battery pack (2) out of the machine (1) from the front. | 33 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Dismantle the dust extraction Switch off the machine. Switch off the special dust extractor. Pull the suction hose (3) off the socket (2) off the extraction tube (1). | 34 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Note the voltage given on the rating plate and use a battery pack with corresponding power. Before each use of the cordless wall chaser, check the following: | 35 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
(e.g. due to sudden jamming or breaking of the insert tool). Always hold the machine securely by the handle. Assume a stable position. Concentrate on the work. | 36 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 37
For continuous switching on of the slide switch (4), then tilt it downwards until it latches into position. The machine is switched on. Work with the machine Fig. 10: Working direction of the machine | 37 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 38
Page 13. Switch off machine Finish the milling operation. Pull the diamond wall chaser with rotating diamond discs carefully out of the cut chase. | 38 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Never use the diamond discs to break out the centre of the chase. Remove the centre of the chase Use a suitable tool (e.g. chisel) to break out the centre of the chase in the wall. | 39 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 40
Fig. 12: Breaking out the centre of the chase with a chisel | 40 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Only servicing and repair firms authorised by BAIER may carry out maintenance of the machine. Ensure that only original spare parts and original accessories are used. | 42 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
(e.g. insulate with adhesive tape). Please follow the notes on transporting Li-ion rechargeable batteries Chapter 2.5, Using and handling the battery pack; Page 10). | 43 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
They are available from authorised dealers. Use the grease type and grease quantity according to the valid grease list. Use of non-original parts can cause consequential damage to the machine and an increased risk of accidents. | 45 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 46
These components include, among other things, carbon brushes, ball bearings, switches, power cord, seals, shaft sealing rings. Wearing parts are not covered by the warranty. | 46 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...
Page 47
Notes | 47 | ABDN 20 | EN | ID No. 10154 | V01 | 2021-11...