USER MANUAL HOUSEHOLD SOFTENER 0. MAIN SPECIFICATIONS ELECTRONIC TIMER ALLOWS TO CONTROL ALL PARAMETERS REGENERATIONS DELAYED OR INMEDIATE PROGRAMMING MIXING VALVE ALLOWS TO REGULATE THE RESIDUAL HARDNESS INTEGRATED BY-PASS ALLOWS TO ISOLATE THE SYSTEM FROM INSTALLATION ELECTRONIC ADAPTER ELECTRONIC ADAPTER EASY TANK SALT FILLING SPECIAL FOR SOFTENER...
Then, collect all necessary materials and tools smart design as for its easy and intuitive operation. for the installation. Your softener DENVER PLUS will provide you and your Check the plumbing installation. family the following advantages. All installations must be done according to the law in •...
Page 6
Below are the most usual equivalences. ions, so it can continue softening water. In DENVER PLUS PLUS systems the regeneration process UNITS ppm of CaCO3 º French...
Page 7
For the DENVER+ equipment, please respect the mini- same is optimized. mum and maximum flow rates indicated in the Techni- cal Characteristics section.
• The ambient temperature must be between 4 ºC and softening, provided inside the vessel. 45 ºC. • DENVER PLUS cabinet, made of plastic, with salt capa- • The system should be installed in a dry environment, city for multiple regenerations.
Page 12
WITHOUT LEAD. • In the event that this is deemed DENVER PLUS, it can 5. Grounding: When installing a plastic pipe between be raised a maximum of 1.5 m, provided that the inlet two metallic pipes, a grounding cable must be installed pressure is higher than 4 bar.
If desired it can be installed a by- by qualified technical people. Please follow the advises pass with 3 valves. The bypass of DENVER PLUS systems of section 5 and warnings of this manual. has two positions.
Page 14
5. You will be supplied with a in and out noryl set of drain line to the water softener valve drain fitting. Use a connections male 1”.Be sure that the clips snap firmly hose clamp to hold the hose in place. into place so the bypass will not pull out.
Page 15
Keyboard: • Hardness units: to be programmed in ppm CaCO3. Start-up settings: 01:48 29-Mar. Unblock the timer in case that is blocked, by pressing “SET/MENU” key for 3 seconds. MR 03.98/04.00 Push the “SET/MENU” key for 5 seconds in order to ac- cess the programming.
Page 16
once the “REGEN” key. Display will show the following 6.5. INFORMATION SHOWN BY THE DISPLAY message: While in service the system will shown different infor- mations, that will alternate between the following ones: PRESS SETTINGS Date (Month/Day/Year) and time of day 3S TO UNLOCK 2019/02/06 12:30...
Software setting Treated water since start-up TOTAL TREATED VALVE MODE SOFTENER UF Over run total: 7. START UP OVER RUN TOTAL 7.1 HYDRAULIC START-UP Prior to initiate the start-up of the system make sure that all previous steps regarding installation. Ensambling Current flow and peak flow: and programming have been correctly effected and ac- cording to the instructions of this manual and accor-...
Page 18
As stated out in section 2.7. it is recommended not to supply completely softened water to household insta- llations. DENVER PLUS systems have a residual hardness regu- lator that allows to adjust the hardness quantity in the treated water. This works making a small test of non treated water with...
8. MAINTENANCE/SANITIZING The DENVER PLUS softeners, being automatic, do not require a complex maintenance. In order to ensure a correct working of the system it is enough to make the following checking from time to time as showed in the table below:...
Page 20
REMOVING INSCRUSTATION: Once a year it is recommended to make a cleaning with Clean Softener (611000), a product specially designed for the cleaning of your softening system. This product, because of its special formulation, will clean the resin eliminating all kind of iron and other remaining metals that represent a contamination and at at the same time it will remove all possible incrustations in the inner pas- sages of the valve.
9. TROUBLESHOOTING GUIDE PROBLEM MAY CAUSE SOLUTION 1. The transformer is not connected. 1. The timer doesn’t 1. Plug the transformer (power supply). work 2. Electric cable deffective. 2. Replace the cable. 3. No power. 3. Revise the installation. 4. Deffective transformer 4.
10. WARRANTY · The distributor guarantees the equipment for a period of two years for issues with conformity that is detected during this pe- riod, pursuant to RD 1/2007 of 16 November (Consolidated text of the General Law for the Defense of Consumers and Users). The warranty includes the reparation and substitution of defective pieces by authorised personal by the Distributor or the Official Technical Assistance Service (SAT), where it was installed or in a workshop.
11. INSTALLATION REGISTRATION SHEET NOTES FOR THE TECHNICIAN/INSTALLER: Read this Manual carefully. If you have any doubts, get in touch with the Tech- nical Assistance Service (T.A.S) of your distributor. The data market with * must be filled by the installing technical and transcribed in the WARRANTY SHEET.
12. MAINTENANCE SERVICE DATE SERVICE TYPE NAME, SIGNATURE AND TECHNICIAN STAMP START-UP FULL MAINTENANCE TECHNICIAN PREPARATION STAMP ORDINARY HYGIENISATION EXTRAORDINARY OTHER WARRANTY FULL MAINTENANCE TECHNICIAN PREPARATION STAMP ORDINARY HYGIENISATION EXTRAORDINARY OTHER WARRANTY FULL MAINTENANCE TECHNICIAN PREPARATION STAMP ORDINARY HYGIENISATION EXTRAORDINARY OTHER WARRANTY FULL MAINTENANCE...
Page 25
12. MAINTENANCE SERVICE DATE SERVICE TYPE NAME, SIGNATURE AND TECHNICIAN STAMP START-UP FULL MAINTENANCE TECHNICIAN PREPARATION STAMP ORDINARY HYGIENISATION EXTRAORDINARY OTHER WARRANTY FULL MAINTENANCE TECHNICIAN PREPARATION STAMP ORDINARY HYGIENISATION EXTRAORDINARY OTHER WARRANTY FULL MAINTENANCE TECHNICIAN PREPARATION STAMP ORDINARY HYGIENISATION EXTRAORDINARY OTHER WARRANTY FULL MAINTENANCE...
Need help?
Do you have a question about the Plus 30 and is the answer not in the manual?
Questions and answers